Volume 241 - August 2018
Please follow the procedure below to access
K-Line vehicle systems.
1. Verify the MUT3-SE version is SEW18061-00.
If it’s not SEW18061-00, the scan tool needs to
be updated.
2. Connect scan tool to the vehicle.
3. Turn ignition ON.
4. Click on the STV.

Vehicle Technical Info . . . . . . page 1
Training News . . . . . . . . . . . . . page 12
Training Tips . . . . . . . . . . . . . . page 13
Techline Information . . . . . . . page 15
MEDIC Information . . . . . . . . . page 15

NOTE: “Read Error” message will pop-up after
clicking the STV button. This is normal. It is not a
scan tool software error.

Bulletin Review . . . . . . . . . . . . page 16
MOD 2018 . . . . . . . . . . . . . . . . . page 18

NOTE: The
mark indicates an article is
being repeated from a previous issue of Tech
Talk due to the subject's importance.

GROUP 00 - General
TIN-18-00-007: MUT3-SE SCAN TOOL
SOFTWARE UPDATE VERSION SEW18061-00 —
All K-Line Models.
TIN-18-00-007 was released recently and
states:
“Mitsubishi will release the latest software
update for MUT3-SE: Version SEW18061-00
on 07/02/2018. Previously, MMNA released
TIN-18-00-006 to inform dealers that all
vehicles can be reprogrammed with
MUT3-SE. MMNA would like to inform dealers
that MUT3 diagnostic functions are now
integrated into MUT3-SE. Except for certain
vehicles and functions (please refer to NOTE
below), K-Line vehicles can now be diagnosed
with MUT3-SE.
NOTE: Refer to the following chart in the MDL to
identify what vehicles and functions are still
only available in MUT3.

“MUT3 and MUT3-SE Chart” on MDL, under
service / service tech resources / Service
Related Items / Worksheets, Questionnaires,
Job Aids / Job Aids.
1

5. No VIN will be populated. Please click on the
“Erase icon” shown below to erase vehicle
information that is displayed.

Also in the same location on the MDL is a “PQR
Usage Guide” which will help technicians
understand how to “Add a New” or “Search”
for previously submitted PQRs. The new
Search feature will enable technicians to
confirm the PQR status and provide an
opportunity to directly reply to comments or
questions posed by MMNA.

6. Click on the “Vehicle icon” shown below to
populate the VIN.

NOTE: Many times, Mitsubishi technicians are
the first to see product issues that MMNA
addresses throughout the year. It is critical
that communication between the dealer
technician and MMNA product support stays
current. The best way for information to get
to MMNA is through the dealer Product
Quality Reporting System or PQR. Please
keep in mind that you, the Mitsubishi
technician, are first to see these emerging
issues at your dealership and understand you
play a critical role in making the Mitsubishi
brand better.

7. The vehicle information will pop-up and
now, the vehicle systems can be accessed to
diagnose the vehicle.”

If you have any questions, please do not
hesitate to contact your District Parts and
Service Manager.”
TIN-18-00-009: MB991855V (12-13 PIN
REPROGRAMMING
ADAPTER)
NOW
AVAILABLE FOR PURCHASE — 2002-06
Montero, 2003-06 Outlander.
TIN-18-00-009 was released recently and
states:
“To reprogram 2002 - 2006 Montero and 2003
- 2006 Outlander vehicles, MB991855 is
necessary. This tool was removed from our
essential tool kit due to its limited application
and became part of our tool loaner program.
Now, this tool can be purchased by ordering
part number MB991855V from your facing
PDC.”

TIN-18-00-008: RELEASE OF NEW PQR
(PRODUCT QUALITY REPORTING) SYSTEM —
All Models and Years.
TIN-18-00-008 was released recently and
states:
“There
is
good
news
for
those
dealers/technicians who complete Product
Quality Reports. MMNA is launching a new
Product Quality Reporting (PQR) system
effective early July, 2018. This new PQR
system replaces the old PQR system and is
designed to be more user friendly and will
enhance communications between MMNA
and the dealers.
The new PQR system is on the MDL in the
same location as the old PQR system: MDL >
service > systems > Product Quality
Reporting (PQR).

Part Name: 12-13 Pin Reprogramming Adapter
Part Number: MB991855V
Current Price: $17.10

2

DEALER LETTER: STATE OF CALIFORNIA
PROPOSITION 65 WARNING LABEL — All
2018-19 Models (During PDI).
A Dealer Letter was recently sent to all
California dealers and states:
“The new California Proposition 65 safe
harbor language requires that by August 30,
2018, warnings for exposures to chemicals
that cause cancer and birth defects or other
reproductive harm that occur during the
operation, service, and maintenance of a
passenger vehicle must be provided.
One of these notices is:
a warning label attached to the driver's
door window
MMNA will be shipping an initial supply of
warning labels to all California dealers
beginning the week of August 20th.
Additional labels can be ordered through
normal parts channels – part number
PROP65WL (roll of 50 labels).
Beginning August 30, 2018, dealers must
install this label during Pre-Delivery
Inspection (PDI). Please see attached
instructions for proper placement of the label.
Failure to install the label at PDI may result in
partial or full chargeback of the PDI claim.
Labels do NOT need to be applied on vehicles
that have already been PDI’d.
Dealers will be automatically reimbursed
dealer net plus applicable mark-up for the
label cost – see Warranty Bulletin 2019-002
for additional details.
To ensure compliance with the requirements
of California Proposition 65, it critical that
these warning labels are properly installed
during PDI.
Please contact your District Parts and Service
Manager with any questions.
Dealer Installation Instructions for Prop 65
Label: Part Number PROP65WL

3

1. Prepare (paper) template (see page 3).
Position template on the outside of the
driver’s side window with the bottom along
the rubber strip and the righthand edge at
the B-pillar corner.
(Hold in place with tape if needed).

2. Clean the label application area on the
inside of the driver’s side window (if needed).

3. Apply label as shown. Label should be
parallel to the bottom of the window (@ 5 mm
above the rubber) and not cover any part of
the DOT information etched into the glass.

TEMPLATE (PROP 65 LABEL)

Gently push out any trapped air bubbles.
NOTE: The label can be removed and reapplied if
necessary.

4. END.”

NOTE: The template above may be printed on any
printer (select “Fit” to page, 8-1/2 x 11” paper).
However, exact size cannot be guaranteed,
please measure after printing to ensure
accuracy.

4

GROUP 13 - Fuel
DTCs P0420 & P0421: PROPER CATALYST
DIAGNOSIS AND PART IDENTIFICATION —
2013-15 Outlander Sport/RVR.
NOTE: This article is being republished to clarify
DTC applicability in the table.

MMNA is investigating catalytic converter
DTCs and noted confusion in DTC recording
and in some cases incorrect parts replaced.
The following table is a simplified version of
the DTC, model application, and monitored
catalyst.
Please confirm in CAPS the proper part
number by using the individual vehicle's VIN.

DTC P061A: INTERNAL CONTROL MODULE
TORQUE PERFORMANCE INVESTIGATION
COMPLETE — 2018 Eclipse Cross.

MODEL
YEAR

ENGINE

DTC

MONITORED
CATALYST
LOCATION

2013

2.0 L

P0420

Center Pipe

MMNA has concluded its investigation into
DTC P061A and related DTCs. The information
requested in the May 2018 Tech Talk article is
now superseded by TSB-18-13-002, “MIL
Illumination with DTC P061A.” Thank you to
those dealers who provided input on this
condition.

2.0 L

P0421

Exhaust
Manifold

Please refer to TSB-18-13-002 for software
revision instructions.

2.4 L

P0420

Center Pipe

2014
2015
2015

Please refer to related articles in Tech Talk Vol.
219, March 2016, for additional catalyst
diagnosis and heat shield service parts
availability information.
TIN-18-13-002: ENGINE ECU SOFTWARE
UPDATE IN TSB-18-13-001 & TSB-18-13-002
ADDRESSES BOTH DTC P0068 & P061A — 2018
Eclipse Cross.

DTC P0171: FUEL SYSTEM LEAN — 2011 & newer
Outlander Sport/RVR.
When diagnosing a fuel system lean code,
ensure the quality of fuel and that excessive
levels of Ethanol are not present.
Also check for intake vacuum leaks at the
gaskets and connection points of the EGR
Pipe, EGR Pipe Gasket, and EGR Valve Support
(see illustration). Clean and repair parts as
appropriate to correct the source of the
vacuum leak.

TIN-18-32-002 was released recently and
states:
“An Engine ECU software update will be
available soon to address MFI DTCs P0068 and
P061A that have been improperly set. When
reprogramming the Engine ECU software to
resolve DTC P0068 or P061A, be sure to first
check the software part number as described
in TSB-18-13-001 and TSB-18-13-002.
If the Software Part Number listed is
1860D11603 or higher, then the software
update for P0068 and P061A has been
completed. There is no need to complete the
procedure in both TSBs, as software level
1860D11603 addresses both issues.”

5

EGR Valve

EGR Pipe
EGR Pipe Gasket
EGR Valve Support

GROUP 23 - Automatic Transaxle

GROUP 35 - Brake

TIN-18-23-003: COOLANT LEAKING FROM CVT
HOSES – COLLECTION OF PARTS COMPLETE —
All 2014-18 Mirage, All 2017-18 Mirage G4, and
2016-18 Outlander equipped with 4 cylinder
(2.4L) engine and CVT8 transmission.

TIN-18-35-001: BRAKE FLUID LEAK AT BRAKE
MASTER CYLINDER — 2014-17 Outlander
produced before June 5, 2017.
TIN-18-35-001 was released recently and
states:

TIN-18-23-003 was released recently and
states:

“For concerns of the brake warning light
coming on due to low brake fluid in the brake
fluid reservoir and brake fluid is found on the
front of the brake booster, DO NOT replace the
brake master cylinder.

“This TIN supersedes TIN-18-23-001 and
TIN-18-23-002 to state that the collection of
parts requested in those documents has been
completed.

MMNA recently released TIN-18-23-001 (for
Outlander) and TIN-18-23-002 (for Mirage
and Mirage G4) to collect complete
transmission cooler sets for an investigation
into the condition of coolant leaking from the
CVT hoses (examples of leakage below).
MMNA has now collected enough complete
sets of CVT fluid coolers with hoses and
clamps for a sufficient investigation.
MMNA would like to thank those dealers who
have assisted with this investigation and sent
the parts requested. It is much appreciated.
Going forward, if you encounter cases of
transmission fluid leaking from the CVT
hoses, please follow the normal diagnostic
and repair procedures for this condition.”
2014-2018 Mirage & 2017-2018 Mirage G4
CVT7 Coolant Leakage
(View looking up from bottom of vehicle)

Perform the following:
1. Loosen both brake line nuts completely at
the brake master cylinder.
2. Loosen (do not completely remove) the
two mounting nuts of the brake master
cylinder to the brake booster.
3. Reinstall the brake line nuts to the brake
master cylinder, confirming the flare tube is
installed straight into the brake master
cylinder, hand tighten the brake line nuts
while confirming the brake line remains
straight into the brake master cylinder body,
and torque the brake line nuts to 16 ft-lbs (21
N-m).
4. Retighten the mounting nuts of the brake
master cylinder to the brake booster to 18
ft-lbs (25 N-m).
5. Refill the brake fluid reservoir and perform
brake bleeding.
6. Clean the brake fluid leak from the brake
booster and surrounding areas.
7. Check for any other sources of leaks and
repair as needed.
8. Test drive the vehicle and confirm proper
brake operation.”

2016-2018 Outlander
CVT8 Coolant Leakage
(View looking up from
bottom of vehicle)

6

switch to the trim cover. While pressing
rearward on the switch, tighten the screws.

GROUP 35C - Active Stability Control
System (ASC)
FLUID SEEPAGE AT ABS HYDRAULIC UNIT
— 2015-16 Outlander Sport/RVR, 2016 Lancer,
2016 Outlander.
NOTE: This article is being republished to add
2016 Outlander Sport to affected vehicles.

If, during diagnosis, you suspect fluid seepage
from the area of the ABS hydraulic unit,
before replacing any parts please thoroughly
clean the fluid residue and inspect for
seepage at the six line fittings while the brake
pedal is applied. If seepage at a line fitting is
suspected, slightly loosen the fitting and then
re-torque the fitting to the specification
listed in the Service Manual. After properly
torquing the line fittings, recheck for seepage
with the brake pedal applied. Do not replace
the ABS hydraulic unit for a line fitting
concern unless recommended to do so by
TechLine.

GROUP 42 - Body
DRIVER'S DOOR LOCK BUTTON STICKS IN
“UNLOCK” POSITION — 2018-19 Eclipse Cross.
Should you encounter the subject condition,
check for proper clearance between the door
lock button and trim cover at the front edge
of the button.

Sufficient Gap

Recheck for the sticking condition before
reinstalling the door panel.
Be sure to reset the auto up/down driver’s
window and confirm all door switch and lever
functions work properly.

GROUP 42 - KOS / Wireless Control
Module
LOCATING
ID
CODE
REGISTRATION
INSTRUCTIONS — All Models.
The operation and diagnostic information of
both KOS and non-KOS equipped Mitsubishi
vehicles is in Group 42 of the Service Manual,
which can be found on either the MDL website
(Mitsubishi Dealer Link) or on MEDIC under the
TIR (Technical Information Retrieval) tab.

Gap too small
Front of Vehicle

Too small of a gap at the front may cause the
unlock button to stick at times. You can use a
business card or 0.3 mm feeler gauge to
compare the gap at the front and rear of the
door lock button.
To correct the condition, remove the door
panel by following the procedure in the
Service Manual, then loosen the three
mounting screws that secure the master
7

However, starting from 2011 model year, this
section in the Service Manual does not outline
key registration fully (immobilizer and RKE
function). For these models, separate ID Code
Registration Instructions are available on
MDL. Refer to the following instructions to
locate the electronic Service Manual and the
separate ID Code Registration Instructions.

2. Select “service”
resources.”

For 2010 and older model years: Retrieve the
electronic version of the Service Manual on
MEDIC or on MDL (Instructions follow for MDL).
1. Login to the MDL website at
https://mdl.mmsa.com.

then

“service

tech

3. In the left column, under “service tech
resources,” locate the “Service Related Items”
link.

2. At the center of the screen, select the
“Service & Owners Publications” link to view
the list of Service Manuals for each model and
model year.

4. Under Service Related Items, expand the “ID
Codes Registration Instructions” heading.
Select the desired models to view the
Registration Procedures.

3. The electronic versions of the Service
Manual go as far back as 2002 model year
(including Raider).

For 2011 and newer model years: Retrieve the
ID Codes Registration Instructions on MDL.
1. Login to the MDL
https://mdl.mmsa.com.

website

at

8

GROUP 51 - Exterior
FRONT LICENSE PLATE BRACKET/HARDWARE
NOT SUPPLIED WITH NEW VEHICLE — 2013 &
Newer Models (except 2013-15 Lancer
Evolution).
Most models 2013 and newer may not have
license plate brackets/hardware shipped
with the vehicle. For states that require front
license plates, dealers are asked to use
self­tapping screws for mounting the front