Classification:

AT15-003f

Reference:

Date:

NTB15-037f

August 10, 2018

VERSA SEDAN, VERSA NOTE, AND SENTRA;
CVT VALVE BODY REPLACEMENT WITH CONFIRMED DTC
This bulletin has been amended. A TCM P/N was added to 2015 Sentra in Table A.
No other changes were made. Discard all previous versions of this bulletin.

2012 – 2017 Versa Sedan (N17)
2014 – 2017 Versa Note (E12)
2013 – 2017 Sentra (B17)
APPLIED TRANSMISSION: CVT (RE0F11A)
APPLIED VEHICLES:

NOTE: Does not apply to 2017 Sentra equipped with MR16DDT turbo engine.

IF YOU CONFIRM


If one or more of the DTCs listed in the DTC Chart on page 2 are present in the
Transmission Control Module (TCM).
And


No other DTCs are present other than what are listed in the DTC Chart.

ACTION
1. Go to Repair Overview on page 3 to determine which repairs to perform to the applied
vehicle being worked on.

IMPORTANT: The purpose of “ACTION” (above) is to give you a quick idea of the work
you will be performing. You MUST closely follow the entire Service Procedure as it contains
information that is essential to successfully completing the repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/40

DTC Chart
DTC CODE

DTC/CIRCUIT DIAGNOSIS

P0711

TRANSMISSION FLUID TEMPERATURE SENSOR A

P0712
P0713
P0740
P0743
P0846
P0847
P0848
P0962
P0963
P0998
P0999
P0966
P0967
P099B
P099C

TRANSMISSION FLUID TEMPERATURE SENSOR A
TRANSMISSION FLUID TEMPERATURE SENSOR A
TORQUE CONVERTER
TORQUE CONVERTER
TRANSMISSION FLUID PRESSURE SEN/SW B
TRANSMISSION FLUID PRESSURE SEN/SW B
TRANSMISSION FLUID PRESSURE SEN/SW B
PRESSURE CONTROL SOLENOID A
PRESSURE CONTROL SOLENOID A
SHIFT SOLENOID F
SHIFT SOLENOID F
PRESSURE CONTROL SOLENOID B
PRESSURE CONTROL SOLENOID B
SHIFT SOLENOID G
SHIFT SOLENOID G

2/40

NTB15-037f

Repair Overview
Applied Vehicle has
one or more DTCs in
the DTC Chart

All Applied Vehicles:
Replace the control valve
assembly (valve body)

Repairs in addition to
valve body replacement:





2013-2017 Sentra
2014-2017 Versa NOTE
2013-2017 Versa Sedan



2012 Versa Sedan

Reprogram the TCM





Erase Memory Data
Conform CVTF Deteriortn
Auxiliary gearbox clutch
point learning

END

3/40

NTB15-037f

SERVICE PROCEDURE

OIL PAN, CONTROL VALVE (Valve Body)
Exploded View

JSDIA6707GB

1.
4.

Transaxle assembly
Manual plate

2.
5.

O-ring
Washer

3.
6.

Control valve
O-ring

7.

Strainer

8.

Oil pan gasket

9.

Magnet

10. Oil pan
13. Overflow tube

11. Drain plug gasket

12. Drain plug

: Apply petroleum jelly
: Always replace after every disassembly.
: Apply CVT fluid
: Nꞏm (kg-m, ft-lb)
: Nꞏm (kg-m, in-lb.)

Valve Body: Removal and Installation
REMOVAL
1. Disconnect battery negative terminal.
2. Remove engine under cover.
4/40

NTB15-037f

3. Disconnect the CVT unit harness connector.
4. Remove the drain plug and overflow tube, and then drain the CVT fluid.
CAUTION:
Use caution when looking into the drain hole as there is the risk of fluid entering the eye.
5. Remove the drain plug gasket from the drain plug.
6. Remove the oil pan mounting bolts ( ), and then remove
the oil pan and oil pan gasket.

: Vehicle front

7. Remove the magnets from the oil pan.


Clean magnets.



Clean CVT oil pan.



Reinstall magnets to the oil pan.

8. Remove the strainer bolts , and then remove the strainer
from the control valve.


Discard the strainer. A new one will be used during
assembly.

9. Remove the nut and washer , and then remove
manual plate .
CAUTION:
To remove nut, fix manual plate with flat-blade
screwdriver
(B).
10. Press the CVT unit harness connector into the transaxle
case.
CAUTION:
Never damage the CVT unit harness connector.
NOTE:
Clean around the CVT unit harness connector to prevent
foreign materials from entering into the transaxle case.
11. Remove the control valve bolts , and then remove the
control valve from the transaxle case.
CAUTION:
• Never drop the control valve and manual valve.

5/40

NTB15-037f

INSTALLATION
1. Install the control valve, and then tighten control valve bolts
to the specified torque.
CAUTION:
• Never pinch the harness between the control valve
and the transaxle case.
• Never drop the control valve and manual valve.

2. Install the manual plate and washer , and then tighten
nut to the specified torque.
CAUTION:
To tighten nut, fix manual plate with flat-blade
screwdriver.


Reassembly Torque: 22.1 N•m (2.3 kg-m, 16 ft-lb)

3. Install the new strainer , and then tighten the strainer
bolts to the specified torque.

4. Install oil pan (with oil pan gasket) to transaxle case and
temporarily tighten oil pan bolts ( ).
CAUTION:
Never reuse oil pan gasket.
: Vehicle front

5. Tighten the oil pan bolts to specification in the order shown.
: Vehicle front

6. Tighten the overflow tube to the specified torque.
CAUTION:
If it is not tightened to the specified torque, the tube
may be damaged.
7. Connect the CVT unit harness connector.
8. Connect battery negative terminal.
9. Fill with CVT fluid from overflow tube to the specified level.
Refer to ESM for further information.
10. Install the drain plug and drain plug gasket to oil pan.
CAUTION:
Never reuse drain plug gasket.

11. Reinstall engine under cover.

6/40

NTB15-037f

TCM Reprogramming
IMPORTANT: Before starting the TCM reprogram procedure, make sure:


ASIST on the CONSULT PC has been synchronized (updated) to the current
date.



All CONSULT-III plus (C-III plus) software updates (if any) have been installed.

NOTE:


TCM reprogramming applies to 2014-2017 Versa NOTE, 2013-2017 Sentra, and
2013-2017 Versa Sedan only.



2012 Versa Sedan does NOT require reprogramming.



For more information, see Repair Overview on page 3.

1. Connect the plus Vehicle Interface (plus VI) to the vehicle.
CAUTION: Make sure the plus VI is securly connected. If the plus VI connection is
loose during reprogramming, the process will be interrupted and the TCM may be
damaged.
2. Connect the AC Adapter to the CONSULT PC.
CAUTION: Be sure to connect the AC Adapter. If the CONSULT PC battery voltage
drops during reprogramming, the process will be interrupted and the TCM may be
damaged.
3. Connect the GR8, set to “Power Supply” mode, to the vehicle battery.
CAUTION: Be sure the GR8 is connected securely to the battery. Make sure the
battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery
voltage goes out of this range during reprogramming, the TCM may be damaged.
4. Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range
of the CONSULT PC and the VI.
CAUTION: Make sure to turn OFF all external Bluetooth® devices. If Bluetooth®
signal waves are within range of the CONSULT PC and the VI during
reprogramming, reprogramming may be interrupted and the TCM may be damaged.
5. Turn the ignition ON with the engine OFF.


The engine must not start or run during the reprogramming procedure.

6. Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC,
blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.
IMPORTANT: Make sure to turn OFF all vehicle electrical loads. Make sure the
battery voltage stays between 12.0V and 15.5V during reprogramming. If the battery
voltage goes out of this range during reprogramming, the TCM may be damaged.
7. Turn ON the CONSULT PC.
8. Select/open C-III plus.
7/40

NTB15-037f

9. Wait for the plus VI to be recognized.


Serial number will display when the plus VI is recognized.

Step 9:
plus VI is
recognized

Figure 1
10. Select Re/programming, Configuration.

Step
10

Figure 2

8/40

NTB15-037f

11. Use arrows (if needed) to view and read all precautions.
12. Check the box confirming the precautions have been read.
13. Select Next.

Step
11

Step
12

Step
13

Figure 3
14. If the screen in Figure 4 displays, select Automatic Selection(VIN).


If the screen in Figure 4 does not display, skip to step 15.

Step
14

Example

Figure 4

9/40

NTB15-037f

15. Make sure VIN or Chassis # matches the vehicle’s VIN.
16. If the correct VIN is displayed, select Confirm.

Step 15:
Verify here

Step
16

Figure 5
17. Select Confirm.

Step
17

Figure 6

10/40

NTB15-037f

18. Select TRANSMISSION.

Step
18

Figure 7
19. Select Reprogramming.

Step
19

Figure 8

11/40

NTB15-037f

20. Follow the on-screen instructions; maintain the following conditions:
a.
b.
c.
d.

Ignition ON, with the engine OFF.
Press the Brake.
Press accelerator between ¼ and ½.
Put shift selector in R.

21. Select Start.

Step