passenger seat belt reminder light comes on when the seat belt is unfastened, and goes off
when it is fastened.

Page 10 of 28
TSB-18-00-004

13. WINDSHIELD WIPER DE-ICER (if equipped), REAR WINDOW DEFOGGER AND HEATED DOOR
MIRROR (if equipped).
Check with the engine running. Turn the windshield wiper de-icer (if equipped) and rear window
defogger on, allow time for the windshield wiper de-icer, rear window and mirror elements to
warm up and check them during the walk around inspection. Place your hand on the windshield
wiper de-icer, rear window defogger and heated door mirrors (if equipped) to ensure they are
heating. Be sure to turn off the windshield wiper de-icer and defogger after checking.
14. Turn the ignition switch to the “OFF” position.

C. WALKAROUND INSPECTION
Before starting this section, make sure the ignition switch is “ON” (ensure the engine is OFF) and
place the transmission selector in “R” (reverse) with the parking brake applied. DO NOT START THE
ENGINE.
1.

Check EXTERIOR LIGHTS.
Ensure ALL exterior lights, including stoplights, function properly. Check for chipped or cracked
lenses. Verify the AUTO-OFF headlights function properly (refer to the Service Manual for
checking procedures).

2.

Check Auto Headlights/Rain Light Sensor (if equipped).
a.

With the headlight switch in the AUTO position, cover the sensor with a thick material (like
a fender cover) and confirm headlight operation. Uncover the rain light sensor.

b. With the wiper switch in the AUTO position, confirm wiper operation when water is sprayed
on the
upper center of the windshield.
Be sure to shift to “P,” turn ALL lights off, and turn the ignition switch to the “OFF” position after
completing the inspection.
3.

REMOTE KEYLESS ENTRY (RKE) or FREE-HAND ADVANCED SECURITY TRANSMITTER (FAST)
SYSTEM, THEFT ALARM SYSTEM, ALL DOOR LOCKS, LATCHES, ONE-TOUCH START SYSTEM (OSS)
& IMMOBILIZER.
Multi-function Key with RKE/FAST Key (if equipped)
Check the door and trunk (if equipped) locking and unlocking features.
Ensure the key is removed from the ignition. Close all doors and trunk.
D Use all keys to manually lock and unlock the driver's door and trunk/liftgate (if equipped).
D Press the “lock” button once to lock all doors.
D Pressing the “unlock” button once unlocks the driver's door, and pressing it a second time
within 2 seconds unlocks the other doors and the liftgate (if equipped).
D For remotes with 3 buttons, press the “trunk” button twice to open the trunk. Press the
“Panic” button (if equipped) for 2 seconds to test the panic alarm. Press again to turn off
the panic alarm.

NOTE: Factory-installed RKE systems can be customized for various “answerback” responses, depending
on the model and system installed. Ensure the vehicle's answerback feature is in the full-function
answerback mode, where both the horn and parking lamps signal when the doors are locked, and the
parking lamps signal when the doors are unlocked. Refer to the vehicle Owner's Manual for programming
information.

Page 11 of 28
TSB-18-00-004

FAST Key (if equipped): Additional Checks
a. Ensure door locks operate using the buttons on the FAST key.
b. Ensure door locks operate using the lock/unlock button located on the outer driver's door
handle and the outer front passenger's door handle.
NOTE: The default for the FAST Key system unlocks only the driver's door when pressing the button
located on the outer driver's door handle and all doors when pressing the button located on the outer
front passenger's door handle.

Theft Alarm (if equipped)
a. Lower the driver's window. Turn the ignition OFF and remove keys or transmitters from the
vehicle.
b.

Exit the vehicle, close all doors and lock them using the transmitter. The security indicator
on the instrument panel remains lit for about 20 seconds and then blinks slowly when
armed. For FAST key equipped vehicles, the transmitter must be more than 3 ft / 1m from
the vehicle.

c.

Reach through the open window, manually unlock the door, then open it (vehicles with
FAST; hold the transmitter at arm's length away from the vehicle). The alarm should sound
and the headlights should flash.
TO DEACTIVATE THE ALARM:
Press the unlock button on the transmitter, or turn the ignition switch to the ACC or ON
position (transmitter must be present if equipped with FAST).

d.

Repeat steps a. through c. on the front passenger's door and lock.

e.

Repeat steps a. through c. using the trunk remote release and trunk lock (if equipped).

f.

Repeat steps a. through c. on the hood release.

Door Locks and Latches:
Close each door to check the latch and lock mechanisms. If adjustments are required, refer to
the appropriate Service Manual. Submit a warranty claim for any adjustment performed.
Child Safety Door Lock Operation:
Rear doors should not open from inside when the locking lever (located on the inside rear area
of the door near the latch mechanism) is in the LOCK position.
NOTE: Set the lever to the unlock or “FREE” position when you finish.

Fuel Filler Door/Filler Cap:
D Pull the remote fuel door release lever and make sure it opens.
D Check fuel filler cap operation to make sure it can be removed and installed with moderate
effort.
D Close the door and verify it latches properly.
4.

REMOTE ENGINE START (if equipped).
Instructions for Remote Engine Start operation are kept in the glove box of equipped
vehicles.
a. Remove the key from the ignition (without FAST), close all doors, hood and the trunk
(liftgate).
b. Start the engine using the remote transmitter.
c. Stop the engine using the remote transmitter.
d. Open one door and confirm the engine will not start with the remote transmitter.
e. Open the engine hood and confirm the engine will not start with the remote transmitter.
f. Close all doors, and trunk/liftgate. Start the engine using the remote transmitter. Open the
driver's door while the engine is idling. The engine should stop.

Page 12 of 28
TSB-18-00-004

5.

TRUNK/HATCH/LIFTGATE, TRUNK LIGHT AND TRUNK/CARGO AREA TRIM APPEARANCE.
Check for trunk/liftgate closing quality (make sure it closes easily). Fit should be uniform.
!

WARNING

Make sure there is sufficient clearance for the liftgate to fully open.
a. Check operation of the inside trunk release (if equipped).
b. Verify trunk light/cargo light (if equipped) comes on and all trim is installed properly.
c. Make sure the trunk lid/liftgate closes with normal effort.
d. Vehicles equipped with optional power liftgate:
D Press the liftgate master button (located in the center console in front of the shift
selector). Confirm the liftgate only works with the master button in the ACTIVE position.
Press the button next to the license plate lamp to open the liftgate. When fully opened,
press the close button located to the left of the latch mechanism to close it. Confirm
the liftgate latches securely. Repeat with the dash mounted activation switch (lower
dash, left of steering wheel).
D Open the power liftgate. While it is opening, stop it with your hand. With the liftgate
fully open, press the CLOSE button on the liftgate and stop its movement with your
hand. It should return to its previous position (closed or open).
6.

EMERGENCY INSIDE TRUNK RELEASE HANDLE (if equipped).
Check the operation of the emergency inside trunk release handle. Open the trunk lid and trip
the latch by pushing on the catch with the shaft of a screwdriver to simulate trunk closure.
Remove the screwdriver with the latch in the closed position, and verify the release handle
actuates the trunk release. For more information about the Emergency Inside Trunk Release,
refer to the vehicle's Owner's Manual.

7.

SPARE TIRE PRESSURE AND SPARE TIRE, JACK & TOOLS PROPERLY SECURED.
Spare Tire Pressure (if equipped)
Some models require removal of the spare tire for tire pressure adjustment. Check spare tire
pressure and make sure the spare tire is tightly secured after reinstalling it.
Jack & Tools
Check for jack and tools. For most cars and Outlander Sport/RVR, the tools and jack are in the
trunk or cargo area.
Make sure all tools are properly secured and will not rattle or come loose. Refer to the Owner's
Manual for more information concerning jack and tool location.
Tire Repair Kit (Outlander only, if equipped)
Confirm tire repair kit is complete and is stored under the floorboard of the cargo area.
Tire Repair Kit (Outlander, if equipped)

Figure 7

Tire Repair Kit Contents

Tire
Compressor

1
2

1. Vehicles without 3rd row seat
2. Vehicles with 3rd row seat

Tire
Sealant
Bottle

Speed
Restriction
Sticker

Page 13 of 28
TSB-18-00-004

D. UNDERHOOD
!! IMPORTANT !! Use fender covers to protect the vehicle body.
1.

Check BATTERY charge using the Midtronics Battery Tester and record code on PDI form.
Make sure that battery cable terminals, and any additional wires attached to the terminals are
tight. Make sure the battery is secure.
Ensure the battery is fully charged (minimum 12.6 V), and record code from Midtronics Battery
Tester on PDI form. If necessary, follow Service Manual procedures and recharge it. Remove
the battery maintenance tag (if equipped) and insert it into the vehicle file with other PDI
documentation.

2.

Check ENGINE OIL.
Check engine oil level. If oil is needed, check the the underhood label or appropriate Service
Manual for correct oil specifications. Then add oil if necessary.

3.

Check BRAKE and CLUTCH FLUID.
Check brake and clutch fluid levels using the scale on the plastic reservoir of both master
cylinders (brake and clutch). They should both be at the FULL mark. Add fluid as necessary.
NOTE: Use genuine Mitsubishi BRAKE FLUID, part number MZ311987.

4.

Check COOLANT AND WINDSHIELD WASHER FLUID LEVELS.
Add fluid if necessary.
Coolant: Use only DiaQueen Super Long Life Coolant (genuine Mitsubishi COOLANT, part number
MZ320125).
NOTE: During production of some vehicles, such as Eclipse Cross, the coolant level may be filled above
the ”Full” level mark in the radiator condenser tank (coolant reservoir tank). Do not reduce the coolant
level if it is within 25 mm (approx. 1 inch) of the “Full” mark.
For more details, refer to TIN-18-14-001REV.

Washer Fluid: Fill the washer fluid reservoir using genuine Mitsubishi Washer Fluid (part
number ACH3ZC1X07).
5.

Check for signs of FLUID LEAKS.

6.

Check HOOD LATCH AND SAFETY CATCH.
Make sure the hood release lever pulls evenly and the hood cannot be lifted without releasing
the safety catch.

7.

Check for LOOSE ATTACHMENTS.
Check for loose parts, wiring harness and cable clips and connections, incorrectly routed hoses
and harnesses, and insufficient clearance of components to moving engine parts.

8.

EMISSION CONTROL EQUIPMENT.
The Environmental Protection Agency (EPA) requires this inspection.
Using the underhood label as a guide, verify all emission control equipment is installed.
NOTE: The EPA requires that dealers visually inspect the emission control devices prior to delivery, or,
as an alternative, inspect each vehicle for an illuminated malfunction indicator light (MIL), and if the
light is illuminated, diagnose and correct the malfunction.

Page 14 of 28
TSB-18-00-004

E. UNDER VEHICLE
During PDI, every vehicle should be raised on a lift for under vehicle inspection. Refer to the
appropriate Service Manual for vehicle lift points.
1.

Check for LOOSE ATTACHMENTS.
Make sure all wiring harness clips, brake pipe clips, heat shield fasteners and any other
attachments are properly secured.

2.

Check for FLUID LEAKAGE.
Check for signs of leaks from engine components, transmission, fuel lines, coolant hoses, power
steering lines, and A/C lines (if equipped). Check lines for twists, kinks, proper routing and
clearance to moving parts.

3.

ADJUST TIRE PRESSURE AND INSPECT TIRES FOR DAMAGE.
For tire pressure specifications, refer to the Tire Pressure and Loading label on the driver's side
B-pillar.
!! IMPORTANT !! On some models, the factory over-inflates the tires by 50% to prevent flat
spots during shipment and storage. It is critical to adjust tire pressures to the proper
specifications.
Check all tires for damage such as cuts, foreign objects in the tire, or any other imperfections.
Remove any tire pressure and/or tire balance decals from each tire if present.
NOTE: Low tire pressure on vehicles equipped with a Tire Pressure Monitoring System (TPMS) will
illuminate the TPMS warning light. With cold tires, adjust tire pressure on all vehicles to the
specification shown on the Tire Pressure and Loading Label. If a valve stem cap is missing, refer to
Mitsubishi ASA CAPS and replace it only with the part number quoted for the vehicle. Factory installed
valve stem caps are designed to reduce corrosion and damage to the valve. Refer to TSB-12-31-001
for additional TPMS information.

4.

Remove PLASTIC WHEEL PROTECTORS.

Page 15 of 28
TSB-18-00-004

F. ROAD TEST
*** IMPORTANT ***
RECALLS - Check the Warranty Superscreen for open recalls. Make sure any open recall is
performed BEFORE the vehicle is road tested.

BEFORE the ROAD TEST:

Figure 8

Vehicles should be at operating temperature prior to
performing the following checks. Before beginning
the road test, establish a route that you will use for
every vehicle. Recommended road test duration is at
least 15 minutes and should include a variety of road
conditions.
Record BEGINNING mileage
Record the beginning mileage of your road test on the
PDI form.
Turn off radio before starting the road test.

Warning and indicator lights vary by vehicle and
equipment, some samples are shown below.
Refer to the Owner's Manual and Monroney Label for
a complete list for the vehicle.

S Oil Pressure
S Electronic Power Steering
S Charging System
S Low Fuel Level

1.
S A/T Position Indicator

WARNING, INDICATOR LIGHTS, AND GAUGES.
a.

S Seat Belt Reminder
S Check Engine

Turn the ignition ON. The indicator and warning
lights shown in the illustration should
illuminate (as equipped).

b. Fasten the driver's seat belt and start the
engine. Verify that all indicator lights go out,
except the passenger airbag light.

S ABS / ASC

c.

S SRS (Supplemental
Restraint System)

Unfasten the driver's seat belt and verify the
driver seat belt reminder light comes on.

d. Open a door. Verify the door ajar light comes on.
S High Beam
S Door Ajar
S A/T Temp (Automatic
Transmission Temperature)

e.

The brake warning light should be lit when the
parking brake is applied.

f.

Verify all gauges and lights are working as
equipped.

g. Check operation of the seat belt warning
buzzer and the key reminder buzzer. For
vehicles with the FAST Key system and OSS,
move the transmitter out of the vehicle and
listen for a warning tone.

S Passenger Airbag Light
S TPMS (Tire Pressure
Monitoring System) Light
Optional Safety Systems:
S FCM

S LDW

S RCTA

S BSW

S AHB

S Auto Hold

h. For vehicles with Forward Collision Mitigation
(FCM), ensure the FCM light is displayed on the
MID when the engine is started. Use the FCM
button to toggle the following distance and
confirm the change is displayed in the MID.
i.

For vehicles with Lane Departure Warning
(LDW), Blind Spot Warning (BSW), Rear Cross
Traffic Alert, Auto Hold: Verify the applicable
system light displays on the MID at engine
start-up.

Page 16 of 28
TSB-18-00-004

2.

AUTOMATIC TRANSMISSION (A/T) AND CONTINUOUSLY VARIABLE TRANSMISSION (CVT) SHIFT
INTERLOCK.
Make sure the shift lever can only be moved when the brake pedal is depressed and the ignition
switch is in the “ON” position. For vehicles with OSS, the engine must be running.

3.

A/T / CVT STARTER INTERLOCK (if equipped).
Make sure the engine can be started ONLY when the shift selector is in PARK or NEUTRAL.
For vehicles equipped with OSS, the vehicle must only start if the brake pedal is depressed.

4.

MANUAL TRANSMISSION (M/T) CLUTCH - STARTER INTERLOCK (if equipped).
Make sure the engine will start only when the clutch pedal is fully depressed.

CONDUCT A FULL ROAD TEST
Drive the vehicle to identify dynamic symptoms that may need correction. Use the following
instructions as a guide.
! WARNING

DO NOT ATTEMPT TO TEST ANY SYSTEM THAT CANNOT BE SAFELY TESTED WHILE
DRIVING (e.g., COLLISION MITIGATION SYSTEM [if equipped] or ADAPTIVE CRUISE CONTROL
FOLLOWING DISTANCE [if equipped]).
! WARNING
Your route should be relatively free from traffic so you can safely conduct the
test and concentrate on vehicle operation and performance.
! WARNING
ALWAYS follow all traffic laws and safe driving practices. The PDI road test
should be conducted under a variety of different operating and road conditions.
Vehicles equipped with air conditioning: Place a thermometer in the center vent before beginning
your road test. This will be used later to check air conditioner operation.

1.

A/T: Check A/T / CVT AUTO OPERATION.
a.

From 25 mph (40 km/h), briefly accelerate at full throttle. The transmission should kick
down to 1st gear, then shift to the higher gears. For CVT, the vehicle should accelerate
smoothly.

b. Idle 20 seconds in “N” then shift to “D” then “R” holding each position for more than 3
seconds.
c.

Check for smooth shifting during normal driving. Then upshift through all gears with 20%
and 30% throttle and decrease to a stop. On vehicles with Sportronic™ (with shifter lever
and paddles, if equipped), slide the shifter lever into “Sport Mode” and manually upshift and
downshift to verify proper operation.

d. Check paddle shift operation (if equipped). Ensure proper upshifts and downshifts.
2.

M/T: Check CLUTCH AND M/T OPERATION.
Vehicles equipped with a manual transmission: Check for proper clutch operation and smooth
shifter/transmission operation. Repeatedly shift up and down at least 10 times at idle and at
speeds under 40 mph (64 km/h).

3.

ALL WHEEL CONTROL (AWC) AND SUPER-ALL WHEEL CONTROL (S-AWC) DISPLAY FUNCTIONS (if
equipped).
Ensure the mode display changes (e.g., TARMAC, GRAVEL, SNOW) when toggling the mode
switch.

Page 17 of 28
TSB-18-00-004

4.

Check ENGINE PERFORMANCE.
! WARNING
ALWAYS follow all traffic laws and safe driving practices. Check engine
performance under the following conditions. The throttle should respond without
hesitation.
Part Throttle
At a constant speed of 25-35 mph (40-56 km/h), engine performance should be smooth,
without hesitation.

Under Load
Accelerate to 3/4 throttle. The vehicle should accelerate smoothly, without laboring or
hesitation.
At Cruise
At a constant speed of 45-55 mph (75-90 km/h), engine performance should be smooth,
without hesitation or surging.
5.

Check CRUISE CONTROL.
Cruise control switches are located on the steering wheel.
Control Functions
On/Off - Energizes and de-energizes the system and turns on the indicator light.
Coast/Set - Sets control speed. Also reduces set speed while engaged.
Acc/Res - Resumes previously set speed. Also increases set speed while engaged.
Cancel - Deactivates set driving speed.
!

WARNING DO NOT ATTEMPT TO TEST THE ADAPTIVE CRUISE CONTROL (ACC)
FOLLOWING FUNCTION.
System Operation Check
NOTE: Cruise control will not operate below 25 mph (40 km/h).

a.

Accelerate to 30 mph (50 km/h).

b. Turn on the ON/OFF switch. Make sure the CRUISE light illuminates.
c.

Use the COAST/SET function to set the vehicle speed. The vehicle speed should hold at 30
mph (50 km/h).

d. Increase the vehicle speed slightly by using the ACC/RES button momentarily.
e.

Check each canceling function by depressing the brake, clutch (M/T only), and the CANCEL
button.

f.

Resume the set speed by using the ACC/RES button.

g. Turn the cruise control off by pressing the ON/OFF switch.
Vehicles Equipped with Adaptive Cruise Control/ACC (if equipped)
Perform checks h-k in addition to those for standard cruise control (above).
h. Confirm the MID displays the screen for ACC when set (see Figure 7).
i.

Confirm the Distance Scale toggles from Near to Far when the ACC Distance switch is
pressed.

j.

Press the ON/OFF switch to turn cruise control OFF.

k.

Press and hold the ON/OFF switch until CRUISE displays without the distance scale. The
system is now in normal cruise control mode.

Page 18 of 28
TSB-18-00-004

Figure 9

Adaptive Cruise Control Display
ON/OFF
Switch

ACC
Distance
Switch

6.

50
mp
h
Distance Scale

SQUEAKS, RATTLES, AND WIND NOISE.
Check for any abnormal noise and vibration during your road test, including driveline, pedal, or
steering wheel vibration. Listen for rattles and squeaks from interior components (e.g.
glovebox, seats). Correct them as necessary.
Be sure to close all windows and sunroof and turn off the audio during this inspection.

7.

STEERING OPERATION AND WHEEL ALIGNMENT.
Make sure the steering wheel is centered when the vehicle is traveling straight ahead.
The vehicle should track straight on a level surface, without pulling or drifting. If a problem is
identified, correct it. Refer to the Service Manual for adjustment procedures.

8.