NHTSA ID Number: 10143659
Manufacturer Communication Number: GCI-A0339-07
TSB/Document Date: 2018-08-13
Summary
GENERAL CONSUMER INFORMATION PERTAINING TO AN OWNER'S MANUAL
Blinds
Battery charger 40 Amp
Awning 15 Amp
Spare 10 Amp
Water Pump 10 Amp
Spare 30 Amp
Power Sofa 30 Amp
32
12 VOLT DC UPPER FUSE PANEL
Upper Panel
Access to the upper fuse panel is through the cabinet style next to the driver side rear upper door , inside the vehicle. For ease of
access open the driver rear upper door and snap the style off.
Fuse Schematic
#
Switched Loads
1
2
3
4
5
6
7
8
A
B
Ceiling Lights
Counter Lights
Under Cabinet Lights
Bathroom Lights
Entry Lights
Porch Light
Spare
Spare
Closet Light
CO/LP Detector
Fuse Size
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
10 Amp
Output
Dimming
Dimming
Dimming
Dimming
Dimming
Non-Dimming
Constant
Constant
CONVERTER- FUSE AND AUTOMATIC TRANSFER SWITCH
Located below the galley lowest center drawer. Remove the drawer to access this area. There are two 30 amp blade fuses on the
converter.
The Automatic Transfer Switch will only allow you to get power from one source either shore power or you generator.
33
AUXILIARY BATTERY
The auxiliary batteries (Interstate Sealed AGM deep cycle DCM0075U) are located in the rear large storage compartment.
These batteries operate the Motor Home portion of your vehicle.
NOTE: Wires taped in white are ground wires.
The Ford
chassis battery is located under the front engine hood. Consult your Ford
owners manual for details.
BATTERY CARE
Your auxiliary batteries are a maintenance free AGM batteries. To ensure satisfactory battery performance, battery terminal
cleanliness is essential. NOTE: Please consult your Ford
manufacturer’s instructions for detailed maintenance recommendations for
the vehicle battery.
Warning: Batteries give off explosive gases that can cause severe personal injury. Do not smoke in or around
the battery and keep open flames and other sources of ignition well away from the battery. Remember that
batteries can and do, EXPLODE! Be very careful. Battery electrolytes can cause severe eye damage and skin
burns. Always wear protective equipment (goggles, rubber gloves, a protective apron, etc.) when working with
batteries.
EXTERNAL POWER
A 25- foot, 30 amp power cord is provided with your Pleasure-Way motorhome. In order to activate all power circuits, connect the
yellow power cord to your coach in the driver’s side component/generator compartment and to an adequate 110 volt power source.
The connector is rated for 30 amp capacity. NOTE: The male end of the power cord is a 30 amp plug, therefore you may require an
adapter to convert the plug into the 110 volt style. Most RV parks are equipped with 30 amp plug-ins. Remember to always attach
the power cord to your coach first, and then to the power source
MONITOR PANEL AREA
There is a monitor panel located on the kitchen end gable next to the passenger side entry door. Located in this panel are the
monitors the for the (1) Fresh Water (2) Grey Water (3) Black Water, (8) LP gas and coach battery charge level.
Pleasure-refer to the Monitor Panel owner’s manual for instructions.
34
GENERATOR
If your unit is equipped with a generator, it will be located on the driver’s side. Access to the generator is through the non- locking
large compartment door. There is no access to the generator through the interior of the coach. This prevents exhaust gases from
seeping into the living compartment. The generator will provide an added source of power to run the electrical system when you are
not plugged into a 110 volt power source.
Starting the Generator:
1) Turn on the red disconnect switch.
2) Ensure there is at least a ¼ tank of gas as the generator runs off the van chassis fuel tank. If there is less than a ¼ tank of fuel, the
generator will not start.
3) Press the generator start switch in the Switch panel on the kitchen end gable or the switch panel on the rear fridge partition , the
hour meter for the generator is located on the rear fridge partition..
.
NOTE: It may take a few seconds initially for the generator to start. Your generator draws its gas supply from
the van chassis fuel tank. Once the generator is running, it supplies power to the entire electrical system, just as
if your unit was plugged into a 110 volt power source. You will have to balance your electrical consumption as
you have a limited number of watts/ amps available.
NOTE: Please refer to the generator’s manufacturer’s operating manual for complete operating instructions
and maintenance procedures.
NOTE: If your unit is equipped with a generator, it is essential that you run your generator at least ½ hour a
month under load (microwave, AC, coffee maker, etc.) to keep the generator fuel from damaging the carburetor.
NOTE: For your safety and protection, all generator or generator-ready units are equipped with an
automatic transfer switch that will allow your coach to receive power from either shore power or your
generator.
35
MOTORHOME INTERIOR
INTERIOR COCKPIT MAP LIGHT
Please follow the vehicle manufactures instructions for operating procedures. This light is operated from the engine starting battery
prolonged use will deplete the engine starting ability.
REFRIGERATOR - DOMETIC
Your Dometic refrigerator is designed for 2-way operation, using, 110 volt AC and LP gas power. When the refrigerator is switched
to AC or LP gas, the ammonia/water mixture is heated by a heating element instead of a burner.
When your motorhome is stationary, it should be leveled for your refrigerator to provide the proper cooling. A bubble level should be
placed on the freezer shelf to check the refrigerator for levelness. If the refrigerator is not level you may have improper cooling.
NOTE: Please refer to the Dometic operating manual for complete operating instructions and maintenance
procedures.
MICROWAVE/CONVECTION OVEN (SHARP)
Your Sharp microwave operates of 110 volt AC power only. To use your microwave you must be plugged into shore power or have
the generator running.
NOTE: Please refer to the manufactures operating instructions for maintenance, operation and cooking.
36
TV AND DVD
Your motor home is equipped with TV and Blu-ray DVD components, you will find these located in the rear entertainment center in
the bunk model or in the front console area. These two components are powered by a 110 volt power source (inverter or shore power)
NOTE: Your DVD is a player only as it will not record. To play a CD or MP3 the TV flat screen must be in the
on position.
NOTE: Ensure the TV travel lock is locked into the travel position when the vehicle is in motion.
The travel lock is located directly behind the TV (bunk model only).
22” (BUNK MODEL) OR 32” THEATRE SYSTEM
BASIC OPERATING PROCEDURE
For addition TV, DVD, Antenna, or Inverter information please refer to the appliance owner manuals.
A) COMPONENTS:
1)
2)
3)
4)
22” or 32” Flat Screen Monitor
Blu-Ray DVD player
Inverter
Antenna with booster
37
B) BASIC TV OPERATION:
TV antenna (rotate the TV antenna for best reception) or hook up to park cable.
12 Volt Operation:
1)
Turn the inverter located in the cabinet directly above or beside the TV to the on position. (Switch is located beside the fan on
the back of the inverter opposite end as the plug outlet). Ensure the TV and DVD player are plugged into the inverter and the
inverter is turned on.
(1)
(2)
(2)
2)
Turn the antenna booster on by pressing the black button just above the inverter on the white wall plate. (green light indicates
booster on) Turn the antenna booster on in the rear upper cabinet on the antenna base.
3)
Turn the TV on and select DTV-TV using the input button on your TV or remote.
4)
Using the menu button select - TV, select -Channels, select - Scan Channel. This will bring in all local air channels.
5)
For Cable TV connect a cable extension cord from the cable hookup in the component compartment to the park cable outlet.
Turn the booster off on you TV antenna follow step (4) for auto programing.
6) For DVD operation turn on the DVD player. Using the source button on you TV or TV remote select HDMI 1. Insert a DVD
or Blu-Ray Disc allow the Disc to load and press play.
• To save power while watching TV ensure the DVD player is switched off. Only turn your DVD player on when in use.
For 120 volt Operation
(Generator or Shore Power):
Plug the TV and DVD player into the outlet located above the inverter. Switch the inverter off (Switch is located beside the fan on the
back of the inverter opposite end as the plug outlet).. Use the same programing procedures as the 12 volt operation.
38
FULL SIZE BED ASSEMBLY
(1) To make up the Full-size bed in the Pursuit remove the back rest cushions.
(2) Remove the driver cushion support boards from the driver front closet
(3) Place the first support board on the support rail closest to the fridge and kitchen and slide it back. ( Helpful
hint: lift one side of the main cushion, slide the support board to the kitchen or fridge side allowing the board
to slide between the cushion ands and then drop onto the cushion support board rails)
1)
(2)
(3)
(4) Slide the first support board back to the center of the U and place the second support board on the bed rails.
(5) Place the curved back rest cushions on the right and the left side of the support boards.Place the center back
rest cushion between the curved back rest cushions. (The corner cushions will be stored when the bed is made
up.)
(4)
(5)
FIRST GENERATION BED :
(1)
(2)
(3)
(4)
To make up the Full-size bed in the Pursuit remove the back rest cushions.
With the Table and Table legs removed pull out the bed support boards using the pull strap located in the center of the U.
Set the Table in the middle of the support boards with the table close to the leading edge of the support boards
Place the curved back rest cushions on the right and the left side of the Table .Place the center back rest cushion between the
curved back rest cushions. (The corner cushions will be stored when the bed is made up.)
39
BUNK
1)
2)
3)
4)
5)
Unlatch the bunk base from the stow position.
Slide out the bunk base and lock it into bed position.
Flip the bunk base mattress to lay out position.
Insert passenger wedge corner cushion on the right hand side of the bunk mattress.
Remove the ladder from the rear upper center cabinet and lock it into position by inserting it into the clips on the bed rail in a
horizontal position and dropping it to the floor vertical position.
(1)
(2)
(3)
(4)
(5)
(5)
(5)
40
TABLE SET UP AND STORAGE
Your table can be stored behind the Driver front seat against the front closet Engage the thumb latch to hold the table in place.
Your table leg can be stored inside the closet, snapped into the mounting C clips on the left hand side.
To set up the table, remove the table leg from the front storage cabinet.
Locate the table leg flange in the rear of the coach.
Insert the table leg into the leg flange and rotate the leg to lock it into position.
Tighten the table leg collar.
Place the table top onto the table leg flange, ensure the table base cone goes over the table leg cap.
LAPTOP TABLE (Non-bunk model)
Located on the passenger front storage cabinet. (This table will have to be removed to access the water pump)
Lift the front edge of the table
Slide the table top up till it can be tilted 90 degrees
Push the table top out toward the passenger wall panel.
WARNING: Always ensure this table is in the storage position with the passenger seat facing forward while
the vehicle is in motion.
41
SKYLIGHT (may be equipped with one or two)
Basic Operation:
Unlatch the two skylight locks. (0ne on either side)
Snap handle out or the retainer clips and push up. (you can lock the skylight open by using the handle retaining clip)
Clip the screen/ shade runner together and slide it to the desired location
NOTE: Always ensure you’re your skylights are closed while vehicle is in motion.
OPTIONAL ROOF VENT/FANTASTIC FAN
Located in the ceiling in front of the bathroom door. This fan is optional and replaces the front skylight.
This is an exhaust fan.
Please refer to your Fantastic Fan manual.
AIR CONDITIONER ( DOMETIC 13,500 BTU Low Profile)
Switches for this AC unit are on the base of this unit, it is not controlled by a remote thermostat. See the Dometic manual for operating
instructions.
42
TFT REAR VEIW CAMERA (Over mirror)
Back up camera and monitor will come on when the ignition key is in the auxiliary position. The camera and monitor can be shut off
by using the power button on the monitor. The monitor is also blue tooth enabled. For pairing follow these steps.
(1)
(2)
(3)
(4)
(5)
Press [M] button on the monitor several times until Blue Tooth is featured.
Press [^] up arrow to turn on the Blue Tooth
Turn the Blue Tooth on your personal device (phone )
Press [V1/V2] for about two seconds Blue Tooth Pairing will appear on monitor
Search Blue Tooth name CAR BT in your device for pairing
(6) Enter password
8888 on your device. Connecting success will appear on the monitor.
Once you have successfully connected your device
(1) Press the [^] up arrow on the monitor to receive your call
(2) Press the [v] down arrow on the monitor to end the call
For all other information and instructions for the backup camera/ monitor please refer to the operating instruction sheet contained in
your owner’s manual package.
CLARION INDASH NAVIGATION SYSTEM
Please refer to your Clarion NX501 for operating instructions
This radio is Sirius Satellite Ready. The SCC1 will have to be added to activate Sirius Radio
CAREFREE 12 FOOT ELECTRIC AWNING
Awning switch is located on the passenger front cabinet next to the side entrance door. This switch will extend and retract you awning.
Ensure that in windy conditions or while the vehicle is in motion that this awning is fully retracted.
43
PURSUIT FEATURES
Features
Dometic 6 Cubic foot two way AC/LP gas fridge /freezer
Dometic 13,500 BTU roof top Air Conditioner
Dometic/Smev two burner glass cook top
Atwood 16,000 BTU Auto Ignition Furnace
Suburban 6 gallon LP gas Auto Ignition Water Heater
Inteli Power 45 amp Converter with Charge Wizard
Progressive Dynamics AC distribution panel
Progressive Dynamics 5100 series Automatic Transfer Switch
Sure-Flo Demand Water System
Corian and Glass Round shower enclosure
Thetford China Bowl foot flush Toilet
CO/LP gas detector, Smoke Detector, Fire Extinguisher
Carefree 12’ Power Awning
Sharp Convection/ Microwave Oven
Dual Interstate AGM auxiliary Deep cycle batteries
32” Vizio LED TV with Blu-Ray Player featuring WIFI & Jack Antenna
22” Vizio LED TV with Blu-Ray Player featuring WIFI & Jack Antenna
Multiplex Wiring and Switch system
Power Day Night Shades
Probe less Tank Monitor Panel System
LED interior Lighting, LED Porch light
Ultra Leather Fabric
Back up Camera and Monitor
Clarion In Dash Touch Screen Navigation, Blue Tooth stereo system
Opening Sky Lights including Shade and Screen features
Single Lever Faucets
60”X80” Queen Sized Bed with a 3” Memory foam topper
U-Shape Dinette
Maple Styles, Doors, Trim and Crown Moldings
Corian Counter Tops and Back Splashes
Vinyl Flooring
4 KW Onan
Generator
Full Size Spare Tire with Continental
Cover
Full Body Paint
Front Over Cabin Pull Out Bunk
Standard Bunk
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
n/a
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
n/a
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
n/a
X
X
X
X
X
X
X
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: GCI-A0339-07
Replacement Service Bulletin Number:
MFR Communication Date: 2018-07-13
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA
AutoAuth: Now supports FCA
SGW module for Chrysler
, for Jeep
, for Dodge
(2018+), for Fiat
(2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford
, for Lincoln
, and for Mazda
ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order - 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW
, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford
, for Mazda
, and for Lincoln
. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase - OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.




