iQ EV

01 Install DCC fuse (see page 2) ........................................
02 Install radio antenna* .......................................................

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON,” place gear selector in reverse; turn
on lights and rear defogger. Unlock all doors, release fuel door, release trunk hatch.

01
02
03
04
05
06
07
08

Check dome, courtesy, map, and sun visor lights*..........
Check warning/indicator lights, gauges, and horn ...........
Check windshield wipers and washers ............................
Check headlights, instrument lights, turn signals,
dimmer switch, emergency flashers, and brake lights .....
Check inside/outside rear view mirror operation/
adjustment ......................................................................
Check power outlet* and cigarette lighter .......................
Check audio/navigation* systems, set SSP* to iQ, and
set clock ..........................................................................
Install shift-lock override button cover ............................

UNDER VEHICLE (ON HOIST)

OK

January 2013 Rev1
Adjust/
Repair

OK

BEFORE INSPECTION

Adjust/
Repair

2013 PRE-DELIVERY SERVICE CHECK SHEET

01 Remove disc brake anti-rust covers/anti-corrosion
wheel film* ......................................................................
02 Activate and initialize Tire Pressure Warning System
(TPWS) (see page 2) ......................................................
03 Inspect tires for defects/damage .....................................
04 Install wheel covers/caps/spare tire wheel covers*..........
05 Install rubber body plugs (stored in glove box) ................
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
07 Visually check bolts and nuts on chassis and powertrain
for looseness ...................................................................
08 Inspect under the vehicle for damage, rust, etc. ..............
09 Install Front Wheel Opening Extension Pads ............

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and
driving performance.
Enter Odometer Reading

WALKAROUND INSPECTION

Reading Before Test: _______________ Reading After Test: ________________

Start at left front door. Check window and door lock operation (from master power
switch, if equipped). Continue around vehicle in a counterclockwise direction
checking each door and window operation, child door locks, seat belts, interior
condition, all lights, luggage compartment contents. Finish by checking headlight
aim and continue into UNDER HOOD checks.

01
02
03
04

01 Check door and door lock operation, including each
wireless remote control/theft deterrent system* ..............
02 Check power window operation ......................................
03 Check that vehicle will “Ready On” with all keys .............
04 Check seats and seat belt operation ...............................
05 Check rear defogger .......................................................
06 Check side marker, tail, backup, and license plate lights
07 Check rear hatch/cargo area trim appearance ...............
08 Check tire repair kit and tool installation .........................
09 Check headlight aim ........................................................

UNDER HOOD
01
02
03
04
05

Check brake and power steering fluid levels ...................
Check battery system coolant level .................................
Check electric motor system coolant level .......................
Check heater system coolant level .................................
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) .....
06 Inspect for fuel, oil, coolant, and other fluid leaks ............
Comments:

05
06
07
08
09

Check electric motor operation ........................................
Check gear selector operation .........................................
Check brake and parking brake operation .......................
Check steering operation and off-center/vehicle
pull/flutter .........................................................................
Inspect for abnormal noise and vibration .........................
Inspect for squeaks and rattles ........................................
Check heater and A/C* operation ....................................
Check speedometer operation ........................................
Check cruise control operation ........................................

FINAL INSPECTION AND CLEANING
01 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove protective covers just before delivery
to customer) ....................................................................
02 Verify floor mat application and install using
retaining clips* ...............................................................
03 Visually inspect all interior parts for installation,
damage, fit, dirt, etc. ........................................................
04 Remove Rapgard™ film & clear protective bumper film*.
05 Wash and clean vehicle ...................................................
06 Inspect paint finish for scratches, chips, rust, dents,
damage, etc. ....................................................................
07 Inspect exterior body parts for proper installation,
damage, rust, etc. ............................................................
08 Place Owner’s Guide and first aid kit portfolio*
in glove box ....................................................................
09 Perform Techstream Health Check ................................
10 Install front license plate and license plate cover (see
page 2) ............................................................................
11 Fully charge EV battery .................................................
* Inspect or install when equipped/required.

Completion and retention of this from is required to comply with Toyota’s Warranty Policy.

TECHNICIAN’S SIGNATURE

SERVICE MANAGER’S SIGNATURE

NAME (PLEASE PRINT)

NAME (PLEASE PRINT)

Date

Dealer Name

Dealer Code

We hereby certify that all items
on this form have been checked
and corrected for proper
operation as required.
Vehicle Identification Number (Sticker)

DCC FUSE INSTALLATION
To minimize battery discharge the DCC fuse has been removed and is
stored in the engine compartment relay block. Install the DCC fuse (30A)
and confirm all related DTCs are cleared.
2

DTC Clearing Procedure
1.
2.
3.
4.

Connect Techstream.
Cycle the ignition switch to the “IG-ON” position.
Using Techstream, check any other codes being output.
Erase DTCs (B1650 and B1794) and Freeze Frame data.
NOTE
If any DTCs besides B1650 and B1794 appear, repair the
applicable system according to the Repair Manual.

1

1 Remove DCC Fuse (30A)
2 Install DCC Fuse (30A) Here

TPWS ACTIVATION AND INITIALIZATION
Activation Procedure
1. Connect Techstream.
2. Cycle the ignition switch to the “IG-ON” position and check that the Low Tire Pressure Warning Light blinks for 1 minute
and then remains illuminated.
3. Press or remove the valve core to reduce the tire inflation pressure rapidly by 6 psi (0.4 kfg/cm², 40 kPA), or more, within
30 seconds.
4. Check that the Low Tire Pressure Warning Light goes OFF after all the TPWS sensors are activated.
NOTE
To adjust tire pressure correctly when outside temperature is significantly colder or warmer than shop temperature, follow
the procedures outlined in Service Bulletin No. S-SB-0001-12, “Tire Inflation Pressure Compensation and Adjustment”.
5. Using Techstream, check for DTCs (C2111 — C2114), if no DTCs are stored, continue to Initialization procedure. If these
DTCs are stored, repeat step 3.
Initialization Procedure
Refer to the Repair Manual for the Initialization procedure.

FRONT LICENSE PLATE AND COVER INSTALLATION
For states that require a front license plate, follow the installation
procedures below. For states that do not require a front license plate,
follow the front license plate cover (stored in the luggage compartment)
installation instructions.

1

Front License Plate Installation Procedure
1. Align the installation holes on the front license plate with the dimples
on the front bumper.
2. Directly screw 2 self-tapping screws into the dimples to install the front
license plate.
Use self-tapping screws of a non-corroding type with the following
dimensions.
Nominal Length: 15.0 — 20.0 mm (0.60 — 0.79 in.)
Diameter: 6.0 mm (0.24 in.)

2
1 Dimples
2 License Plate

3

3 Self-tapping Screws

1

Front License Plate Cover Installation Procedure
1. Remove the two metal spring nuts from the bumper cover and discard.
2. Clean the area where the license plate cover adhesive will contact
the bumper.
3. Attach the two plastic clips to the license plate cover.
4. Remove the two strips of adhesive cover from the license plate cover.
5. Insert the plastic clips into the bumper cover holes.
6. Ensure the adhesive strips contact the bumper by pressing on the
edges of the license plate cover.

2

3

5

4
1 Spring Nuts/Bumper Holes
2 Plastic Clips
3 License Plate Cover

4 Adhesive Tape Contact Location
5 Adhesive Tape (Backside of
Cover)