T-SB-0015-12 Rev1

January 20, 2012

Smart Key System Check During PDS

Service
Category General

C) TOYOTA

Technical Service Bulletin

Toyota Supports pie
Section Pre-Delivery Service Market USA oe eesnol
Applicability
YEAR(S) MODE (S) ADDITIONAL INFORMATION
2013 4Runner, Avalon,
Avalon HV, Camry,
Camry HV, Highlander,
Highlander HV, Land
Cruiser, Prius, Prius
C, Prius PHV, Prius
V, RAV4, Sequoia,
Sienna, Venza
REVISION NOTICE
October 16, 2012 Rev1:
* Applicability has been updated to include 2013 model year Avalon HV, Prius C, and Prius PHV
vehicles.
Any previous printed versions of this bulletin should be discarded.
Introduction

Some 2013 model year vehicles are equipped with a Smart Key system, which allows the customer
to enter and start the vehicle without using a mechanical key. To ensure the system is operating
properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected during
Pre-Delivery Service (PDS). The following inspection procedure has been developed to confirm the
proper operation of the Smart Key system prior to vehicle delivery.

NOTE

Check all of the Smart Keys using this procedure.

Warranty Information

OP CODE DESCRIPTION TIME OFP Ti T2
N/A Not Applicable to Warranty a a = a
© 2012 Toyota Motor Sales, USA Page 1 of 5
CP TOYOTA T-SB-0015-12 Rev1 January 20, 2012

Smart Key System Check During PDS

Inspection Procedure

1. Remove ALL Smart Keys from the vehicle.

Page 2 of 5

NOTE
The remaining keys need to be a minimum of 3 feet (1 meter) away from the vehicle.

2. Check Smart Entry function at all the doors.

NOTE
Smart Key MUST be in actuation area No. 1 for this check (see Figure 1 below).

Figure 1.

1

ong My
ae 5
fe Pr soa eee
nko x =

- eee BRR SR)
if Ae 1 | ves i t
* ae } i
iy mS tt} He A
the ee), eh and
\. he oy
4

1 } 4 Door Sensor Vehicles | 2 2 Door Sensor Vehicles

A. Locking operation:

Push the lock button on the outside door handle. All the doors should lock simultaneously. At

this time, one beep will be heard and the turn signal lights will flash once.

© 2012 Toyota Motor Sales, USA

|
>) TOYOTA T-SB-0015-12 Revi January 20, 2012 Page 3 of 5

Smart Key System Check During PDS

Inspection Procedure (Continued)

B. Unlocking operation:

NOTE

After checking the lock function, wait at LEAST 3 seconds before checking the unlock
function.

Grasp the outside door handie (sensors are located on the underside of the door handles).
At this time, two beeps will be heard and the turn signal lights will flash twice.

NOTE

Only the driver's door unlocks when the driver's door handle is grasped. All the doors
unlock when any door handle other than the driver’s door handle is grasped.

3. Check the Wireless Door Lock function.

Using the remote outside of the vehicle, confirm that all doors can be locked and unlocked
using the wireless remote.

© 2012 Toyota Motor Sales, USA
CP) TOYOTA T-SB-0015-12 Rev1 January 20, 2012 Page 4 of 5

Smart Key System Check During PDS

Inspection Procedure (Continued)

4. Check Smart Start function from inside the vehicle.

NOTE
Smart Key MUST be in actuation area No. 2 for this check (see Figure 2 below).
Figure 2.
I
pie
@ f s
fee ed bb LAS
poh Teton a NN
“ or a ‘ 7
Geary 7) Ch. a1) i i
Ti a }=o 720° _ oO
Sate cha) py
ey Sao ne een ee a y if ,
‘i ié
wy 5
1
| 4 4 Door Sensor Vehicles f Ez 2 Door Sensor Vehicles

A. Check for proper activation of the “ENGINE START/STOP” switch.

(1) Make sure the gear selector lever is in the “P" position.

© 2012 Toyota Motor Sales, USA
CP) TOYOTA T-SB-0015-12 Revi January 20, 2012 Page 5 of 5

Smart Key System Check During PDS

Inspection Procedure (Continued)

(2) Without depressing the brake pedal, Figure 3. Engine StarvStop Switch
press the “ENGINE START/STOP” switch
and confirm the mode changes properly.

From the “OFF” mode: e—

» Press once. The power supply mode
is in the “ACC” mode.

* Press twice. The power supply oO —> “Sy => ISSN
mode is in the “iG-ON’ mode.

* Press three times. The power supply ee
mode is in the “OFF” mode.

NOTE

If the “ENGINE START STOP" switch
illuminator blinks in amber, refer to
the Repair Manual.

1 | Light off
2 | Light On

B. Check the engine start/stop operation.
(1} Make sure that the gear selector lever is in the “P” position.

(2) When depressing the brake pedal, check that the green engine switch illuminator
comes on, and push the “ENGINE START/STOP” switch to start the engine.

(3) Push the switch again to stop the engine.

NOTE

When the “ENGINE START/STOP” switch is turned OFF with the gear selector lever in a
position other than “P;” the vehicle electrical system will be in the “ACC” mode. When
the door is opened the Smart Key System Warning Buzzer will sound indicating that the
electrical system is not “OFF” when exiting the vehicle. This may result in a discharged
battery. Be sure to turn OFF the engine AFTER shifting the gear selector lever to the “P”
position.

Checking Procedure:

* Shift the gear selector lever to the “P” position (or check that the gear selector Jever
is in the “P” position).

* Press the Engine Start/Stop switch once and check that the indicator light goes OFF.

5. Repeat steps 2 — 4 with each Smart Key.

© 2012 Toyota Motor Sales, USA