2018

Pre-Delivery Inspection
Technician Reference Document

Effective 4-6-2017-US
Version 1.3

Table of Contents
Technician Reference Document
Technician Reference Document Overview
The Pre-Delivery Inspection Technician Reference Document is designed to be a resource used in hand with
the Pre-Delivery Inspection Checklist (PDI). The PDI Checklist has been simplified to make the process more
efficient, and in doing so, this document has been created to be used as a reference for checklist items that
may have additional information. On the PDI Checklist, you find that certain items have been notated with an
asterisk symbol (*), this lets you know that additional information can be found in this Technician Reference
Document.
Below you will find a list of each model, with the page numbers to their left. After navigating to the desired
page, you will notice each model page is formatted similarly to the PDI Checklists. After each section title is the
original checklist item, followed by any additional information specific to that model.

Table of Contents
3-4

A4/S4/A4 allroad

5-6

A5/S5

7-8

Q3

9-10

Q5/SQ5

11-12

TT/TTS/TTRS

Effective 4-6-2017-US
Version 1.3

Model Year 2018 | Audi Pre-Delivery Reference Document | 2

A4/S4/A4 allroad
Technician Reference Document
Vehicle Preparation

Interior (continued)

•      Deactivate vehicle transport mode

•      Verify proper operation of climate control

This step must be performed with the ignition on/engine
off or the 03 brake module may remain in transport mode.
See TSB 2042954 for resolution.
Deactivate vehicle transport mode (via Special functions >
PDI service > 19-Transport mode activating/deactivating.)
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)*
Using ODIS, right click the 5F-Information control unit 1,
and select “Guided Functions > 5F-Adaptations > Storage of
music activating/deactivating (option 2) and when prompted
for the Optical drive, choose option 1 for “On”
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2018 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque

Ensure proper heating and A/C cooling and open all panel
vents for all zones
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location
•      Verify and set language and Measurement Units
This can be changed in the Settings menu by going to Menu >
Vehicle > Vehicle settings
•      Verify Speech dialog system is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via “Menu->Vehicle->Left Option->Driver Assistance->Parking
Aid”
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off

Refer to Elsa Pro for specification
Media / Radio / SAT
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating
•      Check rear view mirror operation
Check self-dimming function/lighting
Effective 4-6-2017-US
Version 1.3

•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
•      Verify Audi connect Information Packet is present (if
equipped)
Verify Audi connect Information Packet is present, including
Audi brochure, AT&T brochure, AT&T Terms & Conditions
(T&C) (if applicable)
Model Year 2018 | Audi Pre-Delivery Reference Document | 3

A4/S4/A4 allroad
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)

Driver Assistance

•      Turn on the wireless network (if equipped)

•      Verify operation of parking system (if equipped)

Ensure the wireless network is turned on (Telephone > Options > Wi-Fi options > Wi-Fi Mode “Hotspot”)
•      Check Wi-Fi hotspot Visibility (if equipped)
Check Wi-Fi hotspot functionality is enabled and verify the
Access point (SSID) is set to “Audi_MMI__XXXX,” where XXXX
is the last four digits of VIN. via Telephone > Options > Wi-Fi
options > Wi-Fi Mode “Hotspot” > Hotspot settings > Access
point (SSID)

Verify operation of Audi parking system sensors with rear
view camera (if equipped)
•      Verify all vehicle Head-up display functionality (if
equipped)
Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)

•      Enable Google Earth (if equipped)
Enable Google Earth in the Navigation > Map Settings and
verify the white Google logo appears in the bottom right
hand corner of the MMI screen
On-Hoist Inspection
•      Inspect wheel bolts for proper torque
Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2018 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu

Post-Road Test Inspection
•      Check engine oil level
Fill oil to the max level when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> Special functions –> PDI service. Select
option 2, the battery test for new batteries as part of the
pre–delivery inspection and act according to the test result
(ok, recharge, replace). Ensure diagnosis log is uploaded to
the GFF paperless server by selecting “ok” when tester wants
to send the current generated diagnosis protocol online.
(Note: Do not use Guided Function. The diagnosis log will not
be uploaded to GFF paperless)

Driving Performance
•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)

Effective 4-6-2017-US
Version 1.3

Model Year 2018 | Audi Pre-Delivery Reference Document | 4

A5/S5
Technician Reference Document
Vehicle Preparation

Interior (continued)

•      Deactivate vehicle transport mode

•      Check rear view mirror operation

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating)
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
•      Set service reminder
via Special functions –> PDI service –> 17-PDI-resetting SRI
at PDI, counter reset, etc.
•      Perform any open campaigns
Follow instructions listed in campaign documentation

Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control
Ensure proper heating and A/C cooling and open all panel
vents
•      Inspect operation of all power outlets
Inspect operation of front outlet, aux. outlet under armrest,
and rear outlets
•      Check panoramic sunroof and sunshade operation
Verify open/close/vent/deflector at edge and sunshade
operation
Settings
•      Set Time source setting to “GPS” and set Auto daylight
savings time to “on.”
Change time zone appropriate to the dealer location

Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors and
trunk remotely lock/unlock with all keys, including all door
handle sensors with Advanced Key (if equipped)
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Install wheel bolt cover removal tool from PDI kit into
trunk tool kit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit
•      Set spare tire pressure
See separate “2018 Normal Load Condition Tire Pressure
Table” posted on ServiceNet
•      Check battery clamps for proper torque
Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
Effective 4-6-2017-US
Version 1.3

•      Verify and set language and Measurement Units
This can be changed in the Setup/Settings menu
•      Verify speech dialog system is operating
Press the “Talk” button and verify several commands
•      Set “Entertain. Fad.” in Parking aid to an audible level
Via Menu > Vehicle > Driver Assistance > Parking Aid
•      Set “Music volume while parking” to 6 lines
Accessed via MMI rear view camera display, Settings > Music
volume while parking (applies to vehicles with park assist or
rear view camera)
•      Set dealership location in navigation (if equipped)
Set dealership location for following back to dealership
during road test
•      Turn off Manual Speed Warning (if equipped)
This can be changed in the Driver Assistance settings by
going to Menu > Vehicle > Driver Assistance > Speed Warning
> Manual->Select Off
Media / Radio / SAT
•      Verify HD Radio is turned “off”
This can be found in the Radio/Settings Menu
Audi connect (USA ONLY) (if equipped)
•      Verify Audi connect Information Packet is present (if
equipped)
Verify Audi connect Information Packet is present including
Audi brochure, T-Mobile brochure, customer SIM card, T-Mobile Terms & Conditions (T&C)(if applicable)
Model Year 2018 | Audi Pre-Delivery Reference Document | 5

A5/S5
Technician Reference Document
Audi connect (USA ONLY) (if equipped) (continued)

Driver Assistance (continued)

•      Turn on the wireless network (if equipped)

•      Verify all vehicle Head-up display functionality (if
equipped)

Ensure the wireless network is turned on (TEL function
button > Settings Ctrl button > Wi-Fi settings > Wi-Fi active >
select “Visible”)
•      Check Wi-Fi hotspot functionality
Check Wi-Fi hotspot functionality is enabled and verify the
SSID is set to “AUDIXXXXX,” where XXXXX = the last five digits of VIN that are automatically preset in the system
•      Enable Google Earth (if equipped)
Enable Google Earth in the navigation settings and verify the
white Google Logo appears next to the 2G or 3G symbol

Verify the image can be adjusted properly in the viewing
area of the windshield. Verify NAV directions, speed, cruise
control, and lane assist are all visible in Head-Up Display (as
equipped)
Convertible Functionality (if equipped)
•      Test operation of power folding top
Perform with engine running to conserve battery power

On-Hoist Inspection

Post-Road Test Inspection

•      Inspect wheel bolts for proper torque

•      Check engine oil level

Use torque wrench to verify
•      Install wheel bolt covers and center caps as supplied
Wheel bolt covers and center caps can be found in the PDI kit
•      Set and store tire pressures for either sold vehicle OR stock
inventory vehicle
If a known “sold” unit, set to appropriate Normal Load Condition. See separate “2018 Normal Load Condition Tire Pressure Table” posted on ServiceNet. If going to stock, set to
maximum recommended tire pressures listed on the B-pillar
doorjamb, and store tire pressure values in Car/System menu
Driving Performance

Fill oil to the max level when the vehicle is at operating temperature
•      Perform a battery test
Perform the A-battery test for new batteries using GFF in
ODIS Diagnosis –> PDI Service. Select option 2, the battery
test for new batteries as part of the pre–delivery inspection
and act according to the test result (ok, recharge, replace).
Ensure diagnosis log is uploaded to the GFF paperless server
by selecting “ok” when tester wants to send the current
generated diagnosis protocol online. (Note: Do not use Guided Function. The diagnosis log will not be uploaded to GFF
paperless)

•      Verify engine Start-Stop System functionality
Verify the velum sticker is on the start/stop button. Remove
the start/stop information card from the car kit and place it
in the glove box with the owner’s manuals. Additional supply
can be ordered via the Brand Store on AccessAudi
•      Verify engine performance and acceleration
Listen for abnormal noise/vibrations
•      Test drive vehicle applying brakes several times
Apply brakes at least 4 times at 20 mph (35 km/h) to clean
brake rotors. Check for abnormal noise/ vibration/pulsation
•      Calibrate rear view mirror
Calibrate rear view mirror compass to proper zone and check
self-dimming function/lighting (if equipped)
Driver Assistance
•      Verify operation of parking system (if equipped)
Verify operation of Audi parking system sensors with rear
view camera (if equipped)
Effective 4-6-2017-US
Version 1.3

Model Year 2018 | Audi Pre-Delivery Reference Document | 6

Q3
Technician Reference Document
Vehicle Preparation

Trunk Inspection (continued)

•      Deactivate vehicle transport mode

•      Check battery clamps for proper torque

Deactivate vehicle transport mode (via Special functions –>
Service work –> 19-Transport mode activating/deactivating )
•      Set adaption channel to enable CD Ripping (if equipped
with NAV)
Set adaptation channel (via Special functions –> Service
work –> : 5F–Activating/deactivating storage of music). Also
referred to as CD Ripping. Perform 3 button reset of the MMI
to complete the activation. Refer to the owners manual for
model specific button sequence
•      Set service reminder
via Special functions –> PDI Service –> 17-PDI-resetting SRI
at PDI, counter reset, etc
•      Perform any open campaigns
Follow instructions listed in campaign documentation
Exterior
•      Check all key buttons and features
Check functionality of all keys. Verify vehicle starts and runs
with all keys and the start/stop button. Verify all doors
and trunk manually and remotely lock/unlock with all keys,
including all door handle sensors with Advanced Key (if
equipped)
Lighting and Windshield
•      Test front washers (and headlight washers if equipped)
Headlights must be on to test functionality of the headlight
washers
Trunk Inspection
•      Verify power tailgate is operational and set default opening
height
If equipped with power rear tailgate, adjust the opening
height to 75 inches (190 cm) from the ground to the close
button in the rear lid. Press and hold the close button in the
rear lid for at least four seconds to program the opening
height
•      Install wheel bolt cover removal tool from PDI kit into
trunk lid toolkit
Install wheel bolt cover removal tool from PDI kit and wheel
lock key (if applicable) into trunk tool kit to the right of the
spare tire

Refer to Elsa Pro for specification
Interior
•      Check operation of window, lock, and seat controls
Check operation of all switches: Locks, windows, seat adjustment, heated seats (if equipped) and child safety features
•      Inspect mirrors for proper operation
Inspect folding, adjustments, right side tilt in reverse, heating (if equipped)
•      Check rear view mirror operation
Check self-dimming function/lighting (if equipped)
•      Verify proper operation of climate control