70

Figure 38
118/129

NTB17-034e

71. Select Clear.

Step
71

Figure 39

72. Select Yes.

Step
72

Figure 40

119/129

NTB17-034e

73. When CVFT DETERIORATION DATE changes to “0”, select End.

0

Step
73

Figure 41

74. Start the engine.

75. Set the parking brake.

76. Turn OFF the A/C.

77. Bring the engine to normal operating temperature range.

78. Confirm the CVT fluid temperature is over 122°F (50°C).

120/129

NTB17-034e

Auxiliary gearbox clutch point learning
79. Navigate C-III plus to the screen shown in Figure 42.


Diagnosis (All Systems) > TRANSMISSION > Work support

80. Select Auxiliary gearbox clutch point learning.
81. Select Start.

Step
80

Step
81

Figure 42

82. Follow the on-screen instructions in Figure 43 and then select Start.

Step
82

Figure 43

121/129

NTB17-034e

83. With brake pedal still applied, shift the CVT selector lever into the D position.


Figure 45 will be displayed after shifting into D position.

NOTE: The Current status will show EXECUTING, but until the vehicle is shifted into the
D position Auxiliary gearbox clutch point learning will not begin.

Step
83

Figure 44
84. Continue to depress the brake pedal until the Current status shows “Completed” as
shown in Figure 46 on the next page.
NOTE: This may take several minutes to complete.

Figure 45
122/129

NTB17-034e

85. When completed is displayed, select End.

Step
84

Figure 46

86. Shift the vehicle into Park, turn ignition OFF and release the brake pedal.

87. Perform Auxiliary Gearbox Clutch Point Learning (steps 74 to 86) one additional time
(a total of two times).

Erase DTCs

88. Use C-III plus to Erase any transmission DTCs that may have stored.

89. Turn OFF C-III plus.

90. Disconnect C-III plus from the vehicle.

91. Verify the CVT operates normally and no abnormal noises are heard during a test drive.

Procedure complete.

123/129

NTB17-034e

PARTS INFORMATION
REPAIR

DESCRIPTION

Sub-assembly
Repair

KIT-CONTROL VALVE
(For Sentra)
KIT-CONTROL VALVE
(For Versa Sedan or Versa NOTE)
KIT-PULLEY
(For Sentra)
KIT-PULLEY
(For Versa Sedan or Versa NOTE)
KIT-OIL PUMP
Loctite 5460 Sealant (2) (4)

PART #

QUANTITY

3170E-X428C
1
3170E-X428B
31214-3JX9A
1
31214-X429B
31340-X429E
999MP-LT5460P

1
(1) (3)

Control Valve
Replacement

KIT-CONTROL VALVE
(For Sentra)
KIT-CONTROL VALVE
(For Versa Sedan and NOTE)

3170E-X428C

1

3170E-X428B

1

CVT
Replacement

CVT Assembly (6)

(7)

1

Applies to all
repairs

Nissan NS-3 CVT Fluid (1) (4)
Additional Engagement Tool O-Rings (5)
WASHER-DRAIN
(CVT Oil Pan Drain Plug Gasket)
Lens Swab packet

999MP-NS300P As needed
11440
As needed
11026-JA00A

1

J-51963

(8)

(1) Nissan NS-3 CVT Fluid and Loctite 5460 Sealant can be ordered through the Nissan
Maintenance Advantage program: Phone: 877-NIS-NMA1 (877-647-6621) or Website:
Order via link on dealer portal www.NNAnet.com and click on the “Maintenance
Advantage” link.
(2) One container of Loctite 5460 Sealant is good for approximately 5 repairs. This sealant
is not included in any kit.
(3) Bill out Loctite 5460 Sealant (or equivalent) under expense code 008. Do not include
the Loctite 5460 Sealant part number on the claim.
(4) For warranty repairs, Nissan NS-3 CVT Fluid and Loctite 5460 Sealant must be used.
For customer pay repairs, Nissan NS-3 CVT and Loctite 5460 Sealant Fluid or their
equivalents are recommended.
(5) Engagement tool will initially come with 10 O-rings. Additional O-rings are available from
Tech•Mate online: www.nissantechmate.com, or by phone: 1-800-662-2001.
(6) If the CVT is being replaced, no other parts in the table above, except NS-3 CVT fluid or
equivalent, are needed.
(7) Refer to the electronic parts catalog (FAST or equivalent) for the correct part number.
(8) Shop supplies.

124/129

NTB17-034e

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION

PFP

OP CODE

SYM DIA FRT

JD01AA
JD023A

CVT R&R

(2)

(1)
Inspect CVT Belt, Belt = NG (Includes
ZE 32
JX36AA
1.2
control valve R&I)
Replace CVT Sub-assembly
JX45AA
3.0
Reprogram TCM
JE99AA
(2)
(1) Reference the Parts Information Table and use the Kit-Pulley Part Number as the
Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).

EXPENSE CODE
EXPENSE CODE
008

DESCRIPTION
Sealant

MAX AMOUNT
$12.46

OR
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION

PFP

OP CODE

SYM DIA FRT

Inspect CVT Pan for Excessive Debris = NG

JX49AA
0.3
ZE
32
JD01AA
Replace CVT
(2)
JD023A
(1) Reference the electronic parts catalog (FAST) and use the applicable CVT assembly
part number as the Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).
(1)

OR
Submit a Primary Part (PP) type line claim using the following claims coding:
OPERATION
PFP OP CODE SYM DIA FRT
JX37AA
0.4
Inspect CVT Belt, Belt = OK
(1)
ZE 32
Replace Valve Body
JD48AA
(2)
Reprogram TCM
JE99AA
(2)
(1) Reference the Parts Information Table and use the Kit-Control Valve Part Number as
the Primary Failed Part (PFP).
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time (FRT).
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.
125/129

NTB17-034e

KIT PARTS REFERENCE TABLE
NOTE:
 This Table is for reference only. Part numbers listed cannot be ordered individually.


These part numbers are for identification of the correct part within the kit (part
number is listed on the bag for each individual part).



Some parts have more than one part number listed. In this case, one of the part
numbers listed will be in the kit.

KIT-CONTROL VALVE (3170E-X428B or 3170E-X428C) PARTS REFERENCE
(Kit Content)
REFERENCE
#

1

2
3

DESCRIPTION

PART NUMBER

QTY:

VALVE ASSY – CONTROL (Control valve)
(For Sentra)

31705-X428C
or 31705-X429E
or 31705-X422C

1

VALVE ASSY – CONTROL (Control valve)
(For Versa Sedan or Versa NOTE)
GASKET-OIL PAN (Oil pan gasket)
STRAINER ASSY-OIL, AUTO TRANS
(Oil pan strainer)

31705-X428B
31397-3JX0A
31728-3XX0A,
or 31728-3XX0B,
or 31728-3JX0B

1
1

KIT-PULLEY (31214-3JX9A or 31214-X429B) PARTS REFERENCE (Kit Content)
REFERENCE
#

DESCRIPTION

5

PULLEY ASSY
(Sub assembly: Belt & Pulley)
(For Sentra)
PULLEY ASSY
(Sub assembly: Belt & Pulley)
(For Versa Sedan or Versa NOTE)
SNAP RING KIT (Snap ring kit)

6

BOLT (Side cover bolts)

7

SEAL-O RING (Input shaft O ring)

8

SEAL – O RING

4

126/129

PART NUMBER

QTY:

31209-3JX9A,
or 31209-X429C
1
31209-X429B
31506-3JX8B
31377-3JX0E,
or 31377-X420B,
or 31377-3XX2B
or 31377-X424C
31526-3MX0A,
or 31526-X420C,
or 31526-3XX0C
31526-8E000
or 31526-28X0C

NTB17-034e

1
11

1
2

Kit parts reference table continued.

KIT-OIL PUMP (31340-X429E) PARTS REFERENCE (Kit Content)
REFERENCE
#

DESCRIPTION

9

BOLT (Torque converter case bolts)

10

SEAL-LIP (Lip seal)

11

SEAL-O RING (Case O ring)

12

PIN-RET (Manual shaft roll pin)

13

PUMP ASSY-OIL (Oil pump)

14

GSKT-OIL PUMP (Oil pump gasket)

15

SEAL-O RING (Oil filter cover O ring)

16

FLTR ASSY-OIL,AUTO TRANS (Oil filter)

17
18

20

SEAL ASSY-OIL (Torque converter Seal)
SEAL-OIL,DIFF (Axle seals)
SEAL-O RING
(Primary/Secondary/Output Sensor O-ring)
SLEEVE-OIL DIST

21

RING-SEAL

19

127/129

PART NUMBER

QTY:

31377-X420B,
or 31377-3JX0E,
or 31377-3XX2B
or 31377-X424C
31528-1XZ0A,
or 31528-1XA01,
or 31528-1XX0A
31526-X420B,
or 31526-50X0D
or 31526-3JX0B
or 31526-3XX0B
31906-1XF0A
31340-X420B
or 31340-3JX0D
or 31340-X420A
or 31340-3XX0B
31366-3JX0B
or 31366-3JX0A
or 31366-3XX0A
31526-3JX3A
or 31526-3JX1B
31726-28X0A
or 31726-3JX0A
or 31726-3XX0A
31375-3JX1A
38342-3VX0A

19

1

1
1
1

1
1
1
1
2

31526-1XG0C

3

31374 80X01
31525 3JX0B
or 31525 X420A

1

NTB17-034e

2

PART KITS VISUAL REFERENCE


The following Figures show the smaller components of individual kits.



KIT- CONTROL VALVE is not shown.
KIT-PULLEY. Sub-assembly not shown

Figure G
KIT-OIL PUMP

Figure H

128/129

NTB17-034e

CVT Assembly Replacement Approval Procedures

 If CVT inspection indicates CVT assembly replacement is required:

a. Complete the PCC CVT Preauthorization Form in ASIST.

b. Attach the required video (15 seconds or less) to the CVT Preauthorization
Form.


Failure to submit a continuous video showing evidence of abnormalities
and the VIN will cause immediate denial of request for CVT unit
replacement.

c. Call the PCC for authorization at 800-973-9992 (opt 2).

IMPORTANT: Make sure the video has a clear image of the VIN on the F.M.V.S.S.
certification label (VIN label).

129/129

NTB17-034e