NHTSA ID Number: 10127595
Manufacturer Communication Number: GCI-A0225-12
TSB/Document Date: 2018-01-29
Summary
GENERAL CONSUMER INFORMATION PERTAINING TO AN OWNER'S MANUAL
It is recommended that you start and run your vehicle and generator once a
month during the winter season.
Winter Use
We recommend that the water system not be used when the outside temperature drops below the
freezing point. You should ensure that your unit is completely winterized by that time. If it is
necessary to use the water system, we suggest that you bring containers of fresh water with you and
add non-toxic RV antifreeze to the gray and black water holding tanks. NOTE: Keep in mind that
as you add more water to the holding tanks the antifreeze will dilute more than the recommended
amount and may start to freeze earlier at cold temperatures.
26
Living Area Electrical System
The Motorhome living area electrical system is designed for convenience. It is capable of supplying
the vehicle with at least two sources of power. A 12-Volt auxiliary battery supplies power to the
interior components (except AC current plug receptacles, roof air conditioner, microwave, fridge on
A and coffee maker) for short-term use. This battery is automatically charged when the motorhome
is running or when you are plugged into a 110 volt power source with the disconnect switch in the on
position.
For long term use, your vehicle may be powered by plugging into a 110-Volt external power source
with the supplied 25-foot power cable. The yellow 25-foot power cable supplied with your coach
will have to be connected to your coach and then to a 110 volt power source (30 amp outlet is
recommended). This will supply 110-Volt power throughout the interior and supply power through a
power converter to all 12-Volt components.
NOTE: Always connect the power cord to your coach first and then the external power source.
Your unit is equipped with a 110/12-Volt power converter. Its function is to take part of the 110Volt current that is received when the unit is plugged into an external power source and change it to
12-Volts (which powers most of the motorhome components). It also provides 110-Volt power to
the components that only require 110-Volts.
NOTE: The 12-Volt or DC power on your fridge should only be used while in motion or running
the vehicle engine.
12 volt or DC Equipment
110 volt 0r AC Equipment
TV when plugged into the Inverter
Refrigerator when on DC or LP (propane) gas
Interior & Exterior Coach Lights
DVD Player, Antenna Booster and Amplifier
Water Pump
Water Heater
LP (propane) gas & CO Alarms
Generator Start Switch
Furnace
Power Sofa (if equipped)
LP (propane) Switch
TV when plugged into the AC receptacle
Refrigerator on AC
Microwave or Convection oven
Air Conditioner
110 volt Plugs
Coffee Maker (if equipped)
Power Converter
Electrical Distribution Panel
The Plateau is equipped with an Iota distribution panel that houses the breakers for the 110-volt
system and the blade fuses for the 12-volt system. The distribution panel is located on the sofa bench
face.
Remove the large vertical smoked plastic cover panel to access the 110-volt breakers or the small
horizontal cover panel for the 12 volt fuses.
27
12-Volt Manual Reset Breakers and Converter Output Fuses
Your motorhome has two manual re-setting breakers. If you have the optional electric rear sofa, you
will have three manual resetting breakers. Access to these breakers is through a compartment door
found on the driver ottoman in the TS. These breakers have a 40 and 30-amp capacity. The 40-amp
breaker controls the power converter and the 30-amp breaker controls the refrigerator when it’s
running on 12-Volts. If you have the electric sofa option, you will have an additional 30-amp
breaker. This breaker controls the power to your electric sofa.
If you are experiencing any difficulties with your power converter, refrigerator or optional electric
sofa when on 12-Volt, check these breakers first to see that they are tripped. There is a small re-set
button is located on the copper post end of the breaker. Simply push it in if it is tripped.
There are two 30-amp converter output fuses. The converter is located under the power sofa on the
Driver side in the TS. These fuses will blow if the auxiliary battery is cross-wired.
*White is the ground for the RV industry.
12-Volt Battery Disconnect Switch
There is a red key, 12-Volt disconnect switch located on the driver’s side of the coach, in the door
located on the driver’s ottoman, facing the rear of sofa in the TS (same compartment as the manual
reset breakers). When the key is in the “ON” position it will be locked in place. When the key is in
the “OFF” position it can be easily removed, which will stop all 12-Volt power supplied to your
coach. Note This disconnect will have to be on to charge your battery from the converter in
this vehicle. If your vehicle is going to be parked for longer than a 48 hr period turn this switch
to the off position as the detectors and other appliances have a drain on the battery.
Auxiliary Battery
The auxiliary battery (coach battery) is located under the hood of the vehicle; it is an Interstate SRM
27 series battery. This battery operates the Motor Home portion of your vehicle only.
28
The chassis battery and auxiliary battery are two separate
systems. Both batteries are charged from the alternator, but
only the auxiliary battery is charged from the converter.
The Chassis battery powers all chassis related items such as
the map light between the driver and passenger seat, all
dash features, driving lights, power mirrors, locks and
windows.
The auxiliary battery powers all living area lighting, DC
appliances and air ride compressor.
The chassis battery as supplied by Sprinter
is located under the driver floorboard. See your
Sprinter
manual for details.
Battery Care
Your auxiliary battery must be regularly cleaned and maintained at least once a month in order to
provide a reliable and constant power source to your Motor home. To ensure satisfactory battery
performance, battery terminal cleanliness is essential. NOTE: Please see the DODGE![]()
manufacturer’s instructions for detailed maintenance recommendations.
Warning: Batteries give off explosive gases that can cause severe personal injury. Do not smoke in
or around the battery and keep open flames and other sources of ignition well away from the battery.
Remember that batteries can and do, EXPLODE! Be very careful. Battery electrolytes can cause
severe eye damage and skin burns. Always wear protective equipment (goggles, rubber gloves, a
protective apron, etc.) when working with batteries.
Check you battery fluid levels on a regular bases. If the fluid level is down fill it with distilled water.
External Power
A 25- foot, 30-amp power cord. In order to activate all power circuits, connect the yellow power
cord to your coach in the driver’s side component compartment and to an adequate 110-Volt power
source ( 30 amp source.) . The connector is rated for 30-amp capacity. NOTE: The male end of the
power cord is a 30-amp plug, therefore you may require an adapter to convert the plug into the 110Volt style. Most RV parks are equipped with 30-amp plug-ins. Remember to always attach the
power cord to your coach first, and then to the power source.
Monitor Panel Area
There is a monitor panel located beside the microwave, above the closet. In this panel is the carbon
monoxide sensor, water heater control switch, generator control switch (optional) and the water
pump control switch which also monitors the black water, gray water, fresh water, LP (propane) gas
and battery levels.
Generator
29
If your unit is equipped with a generator, it will be located under the vehicle in front of the LP
(propane) tank. Access to the generator is from underneath the chassis. There is no access through
the interior as to prevent exhaust gases from seeping into the living compartment. The generator will
provide an added source of power to run the electrical system when you are not plugged into a 110Volt power source.
Starting the Generator:
1) Turn on the red key disconnect switch.
2) Turn on the LP (propane) gas electrical switch in the exterior component compartment area.
3) Press the start switch in the monitor panel area.
NOTE: It may take a few seconds initially for the generator to start. Your generator draws its gas
supply from your LP (propane) gas tank. Once the generator is running, it supplies power to the
entire electrical system, just as if your unit was plugged into a 110-Volt power source. You will have
to balance your electrical consumption as you have a limited number of watts/ amps available.
Please refer to the manufacturer’s operating manual for complete operating instructions and
maintenance procedures.
NOTE: If your unit is equipped with a generator, it is essential that you run your generator at least ½
hour a month under load (microwave, AC, coffee maker, etc.) to keep the generator fuel from
damaging the carburetor.
NOTE: For your safety and protection, all generator or generator-ready units are equipped with an
automatic transfer switch that will allow your coach to receive power from either shore power or
your generator.
MOTORHOME INTERIOR
Interior Cockpit Map Light
Please follow the vehicle manufactures instructions for operating procedures these instructions will
be found in the Dodge
Sprinter
manual.
Refrigerator - Norcold
Your Norcold refrigerator is designed for 3-way operation, using 12-Volt DC, 110-Volt AC and
propane power. A 12 volt power source must be present for all operations.
When your motorhome is stationary, it should be leveled for your refrigerator to provide the proper
cooling. A bubble level should be placed on the freezer shelf to check the refrigerator for levelness.
If the refrigerator is not level you may have improper cooling.
. NOTE: The refrigerator should be turned to 12-Volt when the vehicle will be in motion and the
Propane must be turned off.
NOTE: The DC or 12-Volt setting is for transportation purposes only. It is recommended that if you
are going to be stopped for more than a short period of time, you should switch your refrigerator to
propane or an AC setting and plug into a 110-Volt supply.
NOTE: Please refer to the Norcold operating manual for complete operating instructions and
maintenance procedures.
30
NOTE: For operating instructions for the remainder of your appliances, please see each respective
manufacturers’ operating manuals.
Microwave- Dometic
Your Dometic microwave operates of 110 volt AC power only. To use your microwave you must be
plugged into shore power or have the generator running. ( the microwave cannot be used at the same
time as the roof AC unit when operating on the generator)
You may also have the Sharp Micro/convection oven installed in your motor home.
NOTE: Please refer to the manufactures operating instructions for maintenance, operation and
cooking.
TV and DVD (Optional)
If your motor home is equipped with TV and DVD components, you will find these located in the
rear entertainment center. These two components are powered by a 12-Volt power source. The TV
is powered by a 12 volt inverter located behind the TV.
NOTE: Your DVD is a player only; it will not record. To play a CD or MP3 the TV must be in the
on position.
22” THEATRE SYSTEM
Basic Operating Manual
A) COMPONENTS:
1) 22” Flat Screen Monitor with swing up cabinet
2) DVD/CD/MP3 player
3) 400 watt Inverter
4) Amplifier
5) Noise reduction ground loop
6) Auxiliary power switch
7) Satellite speakers
8) Antenna booster
9) Optional AC power source
B) BASIC OPERATION:
1) Turn the auxiliary power switch to the on position.
31
*Note you will hear a fan noise come on if you are powering your TV through the
inverter.* (If you are powering your TV through the inverter and the Fan does not come on
check the power switch at the bottom of the inverter.)
2) Turn on the TV using the small button on the side of the TV.
3) Using the source button, select AV for the DVD player or Antenna if you want local air or
cable channels.
4) For Cable simply turn off the antenna booster leaving the source on antenna.
*Note: For local air channels ensure your antenna is cranked up and the booster switch is
in the on position. You may have to rotate your antenna for better reception.
5) Auto Programming for Complete Area Channel Operation ( On your remote)
a)
b)
c)
d)
e)
f)
Push the menu button.
Using the up and down buttons push the down button and move to the Channel symbol.
Push the enter button, using the arrow key move down to auto program.
Push the enter button, using the arrow key move down to air or cable.
Push the enter button, the TV will begin auto programming.
Push the menu button to exit the auto programming.
C) POWER SOURCE :
There are two options for Ac power on you TV system.
For operation the power button in the upper shirt closet must be in the on position.
1) When the motor home is not plugged in to an outside power source or not operating off your
generator, the power source is through your DC battery and the inverter. The inverter is
located behind the TV, unlock the TV flip it up to gain access to the inverter.The inverter has
a power switch located on the unit. A fan will run when the inverter is on.
2) When the motor home is plugged in or operating off of the generator there is a AC power
outlet located behind the TV cabinet, unplug the AC power cord from the inverter and plug it
into the AC outlet. Turn off the inverter to eliminate the inverter fan noise.
A) 400 watt inverter
B) Amplifier
C) Noise reduction ground loop
D) Antenna booster
E) AC Power Source
32
Antenna Booster
A) Green indicator light
B) Booster Off/On switch.
C) 12 volt power source 3 amp
33
Inverter
On/Off switch
TV AC power cord
Samsung 22” LCD TV
Full Digital TV
Right side Operation Button
Source
Menu
Channel Up/Down
Volume Up/Down
Power
.
TS Bed Assembly
Using the sofa switches beside the DVD player on the passenger side, slide the sofa to the full
forward position, using the second switch lay the sofa down to a flat position. Place the bed support
board located in the closet on the maple support rails between the two ottoman benches. Place the
ottoman back rest cushions on the bed board between the ottoman seat cushions.
TD Full Size Bed Assembly
To make up the Full-size bed in the TD model, remove the night table from between the two twin
beds and store it underneath the rear seat compartment accessed from the exterior rear door. Then,
remove the support boards and store them underneath both twin beds. Place these boards along the
oak support rails, which are along the sides of the twin beds. Finally, place the four backrest
cushions in between the twin beds on the support boards.
34
PLATEAU FEATURES:
NORCOLD 3-way Refrigerator
Dometic .7 cu.ft. Microwave
2 Burner Flush Mount Cook Top with Glass Cover
Atwood 16,000 BTU Auto Ignition Furnace
Suburban 6 gal Auto Ignition Water Heater
Sure-Flo Demand Water System
Thetford Flush Toilet
Self Contained Bathroom with Shower & Sink
C.O. Detector
LP (propane) Gas detector
Smoke Detector
Fire Extinguisher
Fantastic Fan Roof Vent
Coach Battery
Battery Disconnect Switch
45 amp Power Converter with Distribution Panel
Monitor Panel System (Black, Gray, Fresh water, LP Gas
& Battery)
Fresh Water Fill
Fresh Water Tank (90.8 L or 24 U.S. Gal)
Grey Water Tanks ( 132 L or 35 U.S. Gal)
Black Water Tank (45.4 L or 12 U.S. Gal)
Generator Ready ( switch, wire for connections & mount
brackets)
Exterior Shower
*Rear Bed Area ( 70” X 76”)
*Power Sofa
Awning Style Windows
Rectangular Table
Porch Light
Cable TV Hook Up
TV Antenna
Phone Jack
Water Heater By-Pass
Fiberglass Running Boards
Counter Top Flip Up
Exterior Plug
Sherwood Decorative Dash
Remote Propane Shut Off
TD
TS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
N/A
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
NOTE: Pleasure-Way Ind. Ltd. reserves the right to make product changes at any time with out prior
notice or obligation.
•
The bed area measurements may vary, due to components inside the vehicle.
35
- 💯【Conta.ct us for Support Directly】If you met any...
- 🔥🔥🔥【2026 AUTEL FLAGSHIP MK900BT MK900-BT, NEW...
- 🚗【3000+ ACTIVE TESTS (50➡3000+), SAME AS MS...
- 🚗【40+ HOT SERVICES FOR 150 MAKES (28+➡40+)】Full...
- 🚗【OE ALL SYSTEM DIAGNOSE, AUTO SCAN 2.0: SCAN LICENSE...
- 【TURN OFF CEL】 This AL319 car scanner diagnostic tool...
- 【EXTENSIVE APPLICATION】 Autel AL319 Compatible with...
- 【FOR END USER & DIYERS】 This error code reader AL319 is...
- 【USER-FRIENDLY DESIGN】 This OBD2 scanner and check...
- 【HIGH-QUALITY SERVICES】 12 months war.ranty from the...
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: GCI-A0225-12
Replacement Service Bulletin Number:
MFR Communication Date: 2017-12-07
MFR Internal Campaign ID/Software Version:
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- 【OE-Level Full System Diagnostics-Lifetime F*REE Software Updates】The VDIAGTOOL D200 OBD2 Scanner for cars is a all system bidirectional scan tool that enjoy lifetime f*ree software updates, delivers complete system coverage. reading/clearing codes across engine, transmission, ABS, SAS, EPB, TPMS plus full access to body, chassis, powertrain and all control modules. This D200 Bidirectional car scanner works with most 1996+ OBD2 gasoline and hybrid
cars and light trucks. It does NOT support pure electric and heavy-duty trucks. PLEASE CHECK COMPATIBILITY BEFORE ORDERING or Contact us with VIN to confirm compatibility. - 【Supports OBD2 Full Functions-ZERO Subscription Fees】D200 Bidirectional OBD2 Scanner is a upgarde of universal car code reader. It supports OBD2 full functions to help you turn off the annoying instrument fault indicator, such as read/clear codes, O2 sensor test, I/M readiness, on-board monitor test, datastream, freeze frame, E-VAP system test, and retrieve vehicle information. This professional obd2 scanner diagnostic tool can full access to diagnostics, reset tools and maintenance features with a single payment. NOTE: The fault code can only be cleared after the vehicle's malfunction has been repaired; please ensure the vehicle issue is fixed before clearing the code.
- 【D200 Hidden 2 Advantages: 1. $169 Expandable 49+ Advanced Resets. 2. $199 Get J2534 P*a*s*s-Thru Programming】Your core car diagnostics and 26 reset remain lifetime f*ree for everyday maintenance. When you need deeper repair capability, upgrade with 3-year access for $169 in Store on VDIAGTOOL App, gaining 49+ advanced resets. D200 configured with J2534 hardware, upgrade only when you need without replacing the entire device. You also can Lifetime Unlock for $199 in Store one-time, perform module programming, software re~flashing and ECU data updates directly. Supports 17+ major brands, including for BMW
, for Audi
, for GM, for Ford
and more. Note:D200 does‘t provide any OE software. - 【Full Bidirectional Control / Active Tests】The D200 car scanner diagnostic tool is a true bidirectional scan tool that lets you send commands directly to the vehicle’s ECU for active tests. Quickly test fuel pumps, relays, solenoids, injectors, cooling fans, windows, sunroofs and more to verify operation instantly. Get dealership-level diagnostic control at a fraction of the cost (ofter $100-200$ per diagnostic visit), reduce guessworkand confirm repairs faster, avoid unnecessary parts replacement, towing fees and wait times.
- 【26 F*ree Essential Reset & Relearn Functions – Everyday Maintenance Made Easy】Handle common maintenance and repair jobs without visiting the shop. The D200 code readers & scan tools includes 26 f*ree high-demand reset functions, including Oil Reset, EPB Service, SAS Calibration, ABS Brake Bleeding, Throttle Relearn, Injector Coding, Headlight Adjustment, Tire Size Reset and more. Perfect for home car owners, mechanics and DIYers – just plug and diagnose anytime, anywhere! Note: Service functions vary by vehicle model—please confirm compatibility.
- 【A MUST-HAVE TOOL FOR DIYERS】 - VDIAGTOOL VD10 car code reader is an incredibly useful obd scanner for each car owner or hobbyist, even for those with little to no experience when it comes to vehicle mechanics! Similar to a fixd car diagnostic tool, using this car diagnostic scanner is extremely easy. All you have to do is attach it to your car OBDII port and you can diagnose car problems in seconds! Read Codes (DTCs); Clear Codes; Live Data; View Freeze Frame; I/M Readiness; Vehicle Information.
- 【KEEP ENGINE IN GOOD STATUS】 - VDIAGTOOL check engine code reader brings a fast access to scan, read the car fault code, show its definition on the screen instantly, troubleshooting to find the root causes of problems, erase the engine fault code and turn off the MIL (Malfunction Indicator Light). Similar to a fixd car diagnostic tool, this car code reader helps ensure your engine stays in top condition.
- 【READ/CLEAR CODES & DTC LOOKUP】- No search online & saving your time, this vehicle car code reader retrieves generic (P0, P2, P3, and U0), manufacturer specific (P1, P3, and U1) codes, pending codes and displays DTC definitions based on the built-in database(more than 3000 codes) on the TFT screen, find out the root causes and clear the codes after fixed.
- 【LIVE DATA & RETRIEVE FREEZE FRAME】 - This diagnostic scan tool for accurate diagnosis enables you to retrieve data from vehicle sensors, such as Engine RPM, Intake air temperature, Short/Long term fuel, Misfire data and etc. The freeze frame is stored in the PCM together with the diagnostic trouble code (DTC) related to the fault. Comparable to a fixd car diagnostic tool, the VD10 car code reader car scanner can be a valuable & practical diagnostic aid and also greatly help when diagnosing intermittent problems.
- 【I/M READINESS for THE S-nn-0-g CHECK】- OBDII vehicle may not pass the annual inspection unless the required monitors since reset are complete. So you should at least read the readiness monitors and make sure they are ready. This car obd2 scanner diagnostic tool is equipped with I/M readiness function to check the operations of the e-m-issi0n system on OBD2 compliant vehicles, run I/M monitor readiness test, checking if the pass vehicle s-m-0-g inspection.
- Pro Features, Home Mechanic Budget: Why pay thousands for factory scan tool? The VD70S scan tool delivers advanced professional diagnostic at an affordable price, including 10x faster 33-66ft wireless scanning, 4000+ active tests, 36+ hot services, ECU coding, PMI function, and OE-level full-system scan with 8-in-one data graph. It rivals expensive shop tools - perfect for DIYer, technician and small shop. Get dealer-grade power without the cost - the VD70S obd2 scanner diagnostic tool makes pro diagnostic accessible to all. The available function tests vary by model—please check compatibility via vdiagtool2 @ outlook . c o m before purchase
- Full Bidirectional Control for Precision Repair: VD70S obd2 scanner gives you direct vehicle module control to test components like fuel pump, injector, A/C clutch, window and more, enabling you to accurately and quickly locate faulty components. Unlike basic obd2 code reader, our advanced bidirectional control lets you actively command system - like triggering the ABS pump to confirm your fix worked. With pinpoint component testing and real-time validation, you can diagnose intermittent issues faster and prevent costly return visits. The VD70S auto diagnostic scanner transforms complex diagnostic into precise, time-saving repair - giving professional-grade accuracy at an unbeatable value
- 33-66FT Wireless Freedom - Faster & More Stable: Say goodbye to 2M cable limits. Easily Perform bi-directional tests like folding mirror, activating light or fuel pump while walking freely around your vehicle - no more cable dragging or repositioning your tool. Unlike other 33ft BT obd2 scanner that still need a cable to handle DOIP vehicle diagnostics, the VD70S bidirectional scan tool delivers a truly cable-free experience - with up to 66ft stable transmission range and faster, more reliable data transfer. With VD70S scanner, you get pro-level flexibility, faster workflow and stable diagnostics without cable clutter or wireless dropouts
- Powerful & Affordable Auto Scanner with 36+ Special Functions: Take control of your vehicle maintenance and save hundreds in shop fees with the VD70S car diagnostic tool. This car tool performs 36+ hot services including ✔Crank Sensor Relearn, Oil Reset, EPB, TPMS Reset, Throttle Adaptation, Injector Coding, ABS Bleed and more. ✔Besides, the VD70S bidirectional obd2 scanner unlocks 100+ advanced vehicle-specific functions under specific system menu, including Idle Relearn, VIN Write, Crankshaft Sensor Relearn, Fuel Trim Reset, ABS Initialization and more. These features help you solve complex system error and restore optimal vehicle performance. Text us your VIN we’ll check the compatibility
- OE-Level Full System Diagnostic, Simplified Workflow: The VD70S car diagnostic scanner delivers OE-level full system scanning (ABS/ECM/BCM/SRS/TCM and more) without the dealership cost. ✔Easily view 8 live data streams, retrieve freeze frame and run active test to quickly identify problem. ✔With advanced bidirectional control, test components like fuel injector and sensor directly to verify repair with certainty. ✔The 8-in-one graphing tracks performance trend to catch intermittent issue like a pro. Whether you're a technician or car owner, the diagnostic scanner provides shop-quality diagnostic to optimize performance and prevent costly repair - all in one affordable tool
Last update on 2026-06-12 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.




