ATTENTION: This Technical
Service Bulletin was issued by
Gulf States Toyota, Inc.
For Toyota Dealers located in the Gulf States Toyota Region:
Please refer to GST Dealer Daily to obtain instructions on how to
order parts and submit a warranty claim (If applicable).
For Toyota Dealers NOT located in Texas, Oklahoma,
Mississippi, Arkansas or Louisiana: For Repair Authorization,
Parts Ordering, and Warranty Claims please contact GST
Accessory Technical Support at 1-800-444-1074.
Thank you for your continued support.

GST-TSB-17-001

March 23, 2017

Service Category:
Section:

Technical Service Bulletin

Vehicle Interior
Theft Deterrent /Keyless Entry

Market:

USA

Alarm Triggering While Driving
Applicability
YEAR(S) MODEL(S)
20132016
2017
20162017

RAV4
RAV4
Corolla

INSTALLED ACCESSORY INFORMATION
DESCRIPTION
Premium Security
System
Premium Security
System
Premium Security
System

ACCESSORY LIO CODE

KIT PART NUMBER

S6

00012-V1320-01

S6

00012-V1620-01

S6

00012-11620-01

Introduction
Some 2013-2017 RAV4 and 2016-2017 Corolla vehicles equipped with the GST Premium Security System
accessory may exhibit improper function of the alarm, including a triggering of the alarm while driving, if the
Power Outlet No.1 fuse is open. The following repair procedure will address this condition.

Parts Information
Vehicle

Kit Part Number

Component Needed for Repair

RAV 4
Corolla

00012-01520-22
00012-01520-22

24-26 Gauge Black T-Tap
18-22 Gauge Red T- Tap

Quantity Required
per Vehicle
1
1

Part Description
15A Mini-Fuse

Quantity
1

Vehicle
RAV 4 and Corolla

Part Number
90982-09022

NOTE
NOT all items from the Kit will be needed for the repair.

2

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

Warranty Information
This repair is covered under the basic vehicle warranty. This warranty is in effect for 36 Months or
36,000 Miles, whichever occurs first from the vehicle’s In-service date.
GST Installed Product
COROLLA
RAV 4 2017
2016-2017
B17023
B17022

Model

RAV 4
2013-2016

Operation
Code

B17021

OFP

00012-V1320-01

00012-V1620-01

00012-11620-01

Labor Time

0.5

0.5

0.5

DIO
B17024
00012-V1320-01
00012-V1620-01
00012-11620-01
0.5

Repair Procedure
1. Disconnect Negative Battery Terminal.
2. Locate and inspect Power Outlet No.1 Fuse.
Is Power Outlet No.1 Fuse Open?
 Yes – Replace 15A fuse and proceed to Step 3
 No – This TSB does not apply

RAV4 Repair Procedure
3. Remove the fuse box opening cover by detaching the 8 clips illustrated in Fig.1

NOTE
Apply protective tape per Fig. 1 to avoid mutilation to vehicle.

Fig.1

3

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

RAV4 Repair Procedure (cont’d)
4. Locate the Instrument Panel J/B Assembly
a. Locate connector 3D

3D

Pin 15 - (YELLOW)
Ignition
(7.5A HTR)
NEW

Pin 14 - (WHITE)
Ignition
(15A Power Outlet
No.1)
OLD

5.
6.
7.
8.

Disconnect the insulated female connector from the Red t-tap on PIN 14 Wire (White)
Reference Page 11 on T-Tap Installation Guide
Install Black T-Tap onto PIN 15 Wire (Yellow)
Re-connect insulated female connector onto installed Black T-Tap

NOTE
DO NOT REMOVE the RED T-TAP from PIN 14 Wire. It must remain
on vehicle after repair is completed

4

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

RAV4 Repair Procedure (cont’d)
9. Re-install the fuse box opening cover
10. Re-connect negative battery terminal and torque to 48 in./lbs
11. Test Alarm System for proper function as listed on Page 10

Corolla Repair Procedure

16MY Corolla
3. Remove Fuse box opening cover


Remove cover per Fig.1 and bolt per Fig.2

FIG. 2

FIG.1

5

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

Corolla Repair Procedure (cont’d)

17MY Corolla
3. Remove No.1 Meter Hood Cluster



Apply protective tape to the area shown in Fig. 3
Using molding remover, disengage the 3 clips and Remove the No.1 Meter Hood
Cluster shown in Fig. 4

A. Disconnect the Front Door Opening Weatherstrip LH
B. Remove Instrument Side Panel LH shown in Fig. 5.


Using molding remover, disengage the 6 clips in the direction indicated by the arrow

C. Remove No.1 Instrument Panel Register Assembly shown in Fig. 6.


Disengage the 4 clips and Remove the No.1 Instrument Panel Register Assembly

Fig. 3

Fig. 4

6

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

Corolla Repair Procedure (cont’d)

Fig. 5

Fig. 6

D. Remove Fuse box opening cover


Remove cover per Fig.7 and bolt per Fig. 8

FIG. 8

FIG. 7
7

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

Corolla Repair Procedure (cont’d)
4. Locate the Instrument Panel J/B Assembly
a. Locate connectors 3C and 3D

3D - Pin 14 - (GRAY)
(7.5A Audio System)
NEW

3D

3C

3C - Pin 4 - (GRAY)
(15A Pwr Outlet No.1)
OLD

8

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

Corolla Repair Procedure (cont’d)
5. 16MY Corolla ONLY - On Connector 3C – Is there a T-Tap present on PIN 4?
 Yes – Proceed to Step 6
 No – This TSB does not apply
6. On Connector 3C - Disconnect the insulated female connector from the Red t-tap on PIN 4
Wire (Gray)
7. Reference Page 11 on T-Tap Installation Guide
8. On Connector 3D - Install Red T-Tap onto PIN 14 Wire (Gray)
9. Re-connect insulated female connector onto installed Red T-Tap

NOTE
DO NOT REMOVE the RED T-TAP from PIN 4 Wire. It must remain
on vehicle after repair is completed

10. Re-install the fuse box opening cover
11. Re-connect negative battery terminal and torque to 48 in./lbs.
12. Test Alarm System for proper function as listed on Page 10

9

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

10

GST-TSB-17-001

March 23, 2017

Technical Service Bulletin

T-TAP Reference Information

11