3.2

Screw in and tighten new fastening screw,
Part No. 000 043 306 00.
Tightening torque 13 Nm (9.5 ftlb.)

3.3

Loosen and unscrew rear fastening screw
 Replacing fastening screws -3- for fuel
collection pipe on cylinder 1–3  Replacing
fastening screws -1-.

3.4

Screw in and tighten new fastening screw,
Part No. 000 043 306 00.
Tightening torque 13 Nm (9.5 ftlb.)

3.5

Replacing fastening screws
Repeat steps 3.1 to 3.4 on the fuel collection
pipe on cylinder 4–6  Replacing fastening screws -4- in order to replace the fastening
screws  Replacing fastening screws -5 and 6-.

4

Raise the engine to installation position and secure it.
For instructions, see  Workshop Manual '100109 Lowering the engine'.

5

Install rear axle carrier together with the lower trailing arms  Workshop Manual '420619 Removing
and installing rear-axle cross member'.
Information
•

The weight must be distributed uniformly on the oil pan.

•

Never apply localised pressure to the oil pan.

Concluding work
Work Procedure: 1
2

Install diagonal braces on the rear axle  Workshop Manual '421319 Removing and installing strut'.
For Cabriolet/Targa vehicles:
Install support plate on the rear axle.
2.1

Install support plate  Workshop Manual '421419 Removing and installing support plate'.

2.2

Install rear underbody cover  Workshop Manual '519419 Removing and installing cover for
rear underbody'.

2017© Porsche Cars North America, Inc.

AfterSales

Feb 7, 2017
Page 7 of 23

2

Service
AH01

ENU

Technical Information

13/17

3

Install retaining frame for charge-air cooler at the left and right  Workshop Manual '261519
Removing and installing retaining frame for charge-air cooler and heat shield'.

4

Install air cleaner housing  Workshop Manual '242519 Removing and installing air cleaner
housing'.

5

Install pressure pipe at the left and right  Workshop Manual '214119 Removing and installing
pressure pipe'.

6

Install air guide for charge-air cooling  Workshop Manual '211019 Removing and installing air
guide for charge-air cooling'.

7

Install rear spoiler  Workshop Manual '66581905 Removing and installing rear spoiler'.

8

Install rear apron  Workshop Manual '635519 Removing and installing rear apron'.

9

Install both tail lights  Workshop Manual '943119 Removing and installing tail lights'.

10 Install engine-compartment blower  Workshop Manual '198119 Removing and installing enginecompartment blower'.
11 Connect ground line to the battery  Workshop Manual '2X00IN Work instructions after disconnecting the battery'.
12 For Cabriolet/Targa vehicles:
Move convertible top out of service position.
 Workshop Manual '6101IN Convertible top service position (Cabriolet)'
 Workshop Manual '6101IN05 Convertible top service position'
13 Perform standardization run for rear spoiler.

Feb 7, 2017
Page 8 of 23

AfterSales

2017© Porsche Cars North America, Inc.

Service

Technical Information

13/17

13.1

Connect a battery charger or power supply,
suitable for AGM type batteries, recommended current rating of 70A fixed voltage
13.5V to 14.5V.
First connect the positive cable of the charger
to the positive terminal of the battery and then
connect the negative cable of the charger
to the ground point for jump-lead starting
 External power connection.
Then switch on the battery charger and start
charging the battery.

13.2

Switch on the ignition.

13.3

Connect the PIWIS Tester to the vehicle
communication module (VCI) via the USB
cable. Then connect the communication
module to the vehicle and switch on the PIWIS
Tester.

13.4

On the PIWIS Tester start screen, call up the
'Diagnostics' menu.

ENU

AH01

2

External power connection

The vehicle type is then read out, the diagnostic application is started and the control unit
selection screen is populated.
13.5

In the control unit selection screen
('Overview' menu), select the 'Rear-end
electronics' control unit and press •F12“
(‘Next’) to confirm your selection  Selecting
rear-end electronics control unit.

13.6

When the question “Create Vehicle Analysis
Log (VAL)?” appears, either press •F12“
('Yes') to create a VAL or press •F11“ ('No') if
you do not want to create a VAL.

13.7

Press •F12“ ('Next') to acknowledge the
Selecting rear-end electronics control unit
message that may appear informing you that
campaigns for the vehicle are stored in the PIWIS information system.

13.8

Once the 'Rear-end electronics' control unit has been found, select the 'Drive
links/checks' menu.

2017© Porsche Cars North America, Inc.

AfterSales

Feb 7, 2017
Page 9 of 23

2

Service
AH01

ENU

Technical Information

13/17

13.9

Select the 'Teach' function and press •F12“
('Next') to confirm your selection  'Teach'
function.

'Teach' function
13.10 Select the function 'Standardization run for
rear spoiler' and press •F12“ (‘Next’) to
confirm your selection  Standardisation run
for rear spoiler.

Standardisation run for rear spoiler
NOTICE
Electrically moved components
•

Danger of limbs being trapped or severed

•

Risk of damage to components



Do not reach into the danger area.



Do not move components or tools into the danger area.



Keep third parties away from the danger area.
13.11 Press •F8“ (‘Start’) to start the standardization run  Starting standardisation run.
The rear spoiler moves automatically to
both end positions and then returns to its
original position.

Starting standardisation run

Feb 7, 2017
Page 10 of 23

AfterSales

2017© Porsche Cars North America, Inc.

Service

Technical Information

13/17

ENU

AH01

2

When the standardization run is complete,
the message "Function completed" is
displayed in the 'Status' box on the PIWIS
Tester display  Standardization run
successful.
13.12 Press •F11“ ('Back') to return to the start
page of the 'Drive links/checks' menu.
13.13 Select the 'Overview' menu and press
•F11“ ('Back') to return to the control unit
selection screen.

Standardization run successful

14 Bleed the high-pressure side of the fuel system using the PIWIS Tester  Workshop Manual '200107
Bleeding fuel system on high-pressure side - First start function'.
15 For vehicles with Lane Change Assist (I-no. 457):
Calibrate control unit for Lane Change Assist  Workshop Manual '917025 Calibrating control unit
for Lane Change Assist'.
16 For vehicles with ParkAssist incl. reversing camera (I-no. 638):
Calibrate reversing camera  Workshop Manual '914325 Calibrating reversing camera'.
17 Read out and erase the fault memory  Workshop Manual '033500 Fault memory for on-board
diagnosis'.
Information
If control units are found to have faults that are not related to this workshop campaign, these must
be found and corrected separately. This work cannot be invoiced under the workshop campaign
number.
18 Switch off the ignition.
19 Disconnect the PIWIS Tester from the vehicle.
20 Switch off and disconnect the battery charger.
21 Remove the vehicle from the lifting platform.
22 Enter the campaign in the Warranty and Maintenance booklet.
References:

 Workshop Manual '033500 Fault memory for on-board diagnosis'
 Workshop Manual '100109 Lowering the engine'
 Workshop Manual '198119 Removing and installing engine-compartment blower'
 Workshop Manual '2X00IN Work instructions after disconnecting the battery'
 Workshop Manual '200107 Bleeding fuel system on high-pressure side - First start function'
 Workshop Manual '211019 Removing and installing air guide for charge-air cooling'

2017© Porsche Cars North America, Inc.

AfterSales

Feb 7, 2017
Page 11 of 23

2

Service
AH01

ENU

Technical Information

13/17

 Workshop Manual '214119 Removing and installing pressure pipe'
 Workshop Manual '242519 Removing and installing air cleaner housing'
 Workshop Manual '261519 Removing and installing retaining frame for charge-air cooler and heat
shield'
 Workshop Manual '4X00IN Lifting the vehicle'
 Workshop Manual '420619 Removing and installing rear-axle cross member'
 Workshop Manual '421319 Removing and installing strut'
 Workshop Manual '421419 Removing and installing support plate'
 Workshop Manual '519419 Removing and installing cover for rear underbody'
 Workshop Manual '6101IN Convertible-top service position (Cabriolet)'
 Workshop Manual '6101IN05 Convertible-top service position'
 Workshop Manual '635519 Removing and installing rear apron'
 Workshop Manual '66581905 Removing and installing rear spoiler'
 Workshop Manual '914325 Calibrating reversing camera'
 Workshop Manual '917025 Calibrating control unit for Lane Change Assist'
 Workshop Manual '943119 Removing and installing tail light'

Warranty processing
Scope 1:

Replacing fastening screws for fuel collection pipes
Body shape and vehicle equipment:
•
•
•

Coupé
without Lane Change Assist
without ParkAssist incl. reversing camera
Working time:
Replacing fastening screws for fuel collection pipes
Includes:
Raising and lowering the vehicle
Reducing fuel pressure
Disconnecting and connecting battery
Removing and installing engine-compartment blower
Removing and installing tail lights
Removing and installing rear apron
Removing and installing rear spoiler
Removing and installing air guide for charge-air cooling
Removing and installing pressure pipes
Removing and installing air cleaner housing
Removing and installing retaining frame for charge-air cooler
Removing and installing diagonal braces
Removing and installing rear axle carrier with lower trailing
arms
Loosening and securing engine
Connecting and disconnecting battery charger
Connecting and disconnecting PIWIS Tester

Feb 7, 2017
Page 12 of 23

AfterSales

Labor time: 375 TU

2017© Porsche Cars North America, Inc.

Service

Technical Information

Without:

13/17

ENU

AH01

2

Performing standardization run for rear spoiler
Bleeding fuel high-pressure system
Reading out and erasing fault memory
Calibrating Lane Change Assist
Calibrating reversing camera

Parts required:
000 043 306 00

Torx screw, BM 6 x 85
– Fuel collection pipe

4 ea.

999 072 875 01

Hexagon-head bolt, M12 x 1.5 x 95
– Rear axle carrier, outer

2 ea.

999 072 931 01

Hexagon-head bolt, M12 x 1.5 x 110
– Rear axle carrier, inner

2 ea.

999 072 930 01

Hexagon-head bolt, M12 x 1.5 x 105
– Lower trailing arm to wheel carrier

2 ea.

999 084 445 01

Lock nut, M12 x 1.5
– Lower trailing arm to wheel carrier

2 ea.

999 072 869 01

Hexagon-head bolt, M12 x 1.5 x 45
– Rear diagonal brace

2 ea.

999 073 443 01

Combination screw, M12 x 1.5 x 40
– Front diagonal brace

2 ea.

N 908 484 05

Hexagon nut, M12 x 1.5
– Engine carrier to engine mount

2 ea.

999 512 707 00

Hose clamp, 9.6 - 11.3 mm
– Vacuum lines

4 ea.

999 512 498 00

Hose clamp, 13.1 - 15.3 mm
– Vacuum lines

2 ea.

Also required for vehicles without PASM/PDCC:
999 084 123 09

Hexagon nut, M10
– Anti-roll bar to connecting link