01 MIL on, DTC P209600 and/or P209800 stored in ECM
01 17 02 2046611/2 February 17, 2017. Supersedes Technical Service Bulletin Group 01 number 17-99 dated
January 27, 2017 for reasons listed below.
Model(s)

Year

VIN Range

Vehicle-Specific Equipment

A8, S6, S7,
S8, RS 6

2013 - 2014

All

4.0L

RS 7

2014

All

4.0L

Condition
REVISION HISTORY
Revision

Date

Purpose

2

-

Revised Service (Updated instructions)
Revised header data (Updated diagnostic codes)

1

01/27/2017

Initial publication

Customer statement:
 MIL on.
Workshop findings:
The following fault entries are logged individually or in combination in the Engine Control Module (ECM) (J623)
(address word 0001):
 DTC P209600 (Post Catalyst Fuel Trim System Bank1 Too Lean)
 DTC P209800 (Post Catalyst Fuel Trim System Bank2 Too Lean)
Any other fault entries regarding the oxygen sensors before the catalyst that may have been logged before or
after the above fault entries should be ignored.
After performing a leakage test of the exhaust system, as part of the GFF test, the Guided Fault Finding
recommends the replacement of the oxygen sensor before the catalyst, this step should not be completed!

Technical Background
The internal reference duct of the oxygen sensor after the catalyst has been contaminated.

Page 1 of 3
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

Production Solution
Not applicable.

Service
Replace the oxygen sensor after the catalyst of the affected bank only, according to the DTC fault memory. The
replacement of the oxygen sensors before the catalyst are not required.
Ensure that the correct sensor per the GFF DTC fault memory is installed. Reference ElsaPro for the locations.

Warranty
Claim Type:

 110 up to 48 Months/50,000 Miles.
 G10 for CPO Covered Vehicles – Verify Owner.
 If vehicle is outside any warranty, this Technical Service Bulletin is informational
only.

Service Number:

2473

Damage Code:

0040

Labor Operations:

Oxygen sensor after catalyst G130 (Bank1)

2473 1921

SRT stated based
on model

Oxygen sensor after catalyst G131 (Bank2)

2473 1922

SRT stated based
on model

Oxygen sensors after catalyst (only if both
DTC are present in current GFF log)

2473 2021

110 TU

GFF

0150 0000

Time stated on
diagnostic protocol
(20 TU Max)

Road test prior to service procedure

No allowance

0 TU

Road test after service procedure

0121 0004

10 TU

Diagnostic Time:

Technical diagnosis at dealer’s discretion

Page 2 of 3
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.

(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:

As per TSB #2046611/2

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.

Required Parts and Tools
Part Number

Part Description

Quantity

VIN specific

Oxygen sensor after catalyst G130 (Bank1)

1

VIN specific

Oxygen sensor after catalyst G131 (Bank2)

1

Additional Information
All parts and service references provided in this TSB (2046611) are subject to change and/or removal. Always
check with your Parts Department and service manuals for the latest information.
©2017 Audi of America, Inc. All rights reserved. Information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any
time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these
materials be modified or reposted to other sites without the prior expressed written permission of the publisher.

Page 3 of 3
© 2017 Audi of America, Inc.
All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of
America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted
in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the
publisher.