8. Select CONSULT-III plus (open C-III plus).
95/128

NTB17-034b

9. Wait for the plus VI to be recognized.


Serial number will display when the plus VI is recognized.

plus VI is
recognized

Figure 1
10. Select Re/programming, Configuration.

Step
10

Figure 2

96/128

NTB17-034b

11. Use arrows (if needed) to view and read all precautions.
12. Check the box confirming the precautions have been read.
13. Select Next.

Step
11

Step
12

Step
13

Figure 3
14. If the screen in Figure 4 displays, select Automatic Selection(VIN).


If the screen in Figure 4 does not display, skip to step 15.

Step
14

Example

Figure 4

97/128

NTB17-034b

15. Make sure VIN or Chassis # matches the vehicle’s VIN.
16. If the correct VIN is displayed, select Confirm.

Step 15
Verify here

Step
16

Figure 5

17. Select Confirm.

Step
17

Figure 6

98/128

NTB17-034b

18. Select TRANSMISSION.

Step
18

Figure 7

19. Select Reprogramming.

Step
19

Figure 8

99/128

NTB17-034b

20. Follow the on-screen instructions; maintain the following conditions:
a.
b.
c.
d.

Ignition ON, with the engine OFF.
Press the Brake.
Press accelerator between ¼ and ½.
Put shift selector in R.

21. Select Start.

Step
21

Figure 9
22. When COMPLETED is displayed, select Next.

Step
22

Figure 10

100/128

NTB17-034b

23. Operate the ignition per the on screen instructions.

Ignition status

Timer

Progress display

Figure 11

24. When OK is displayed, select Next.

Step
24

Figure 12

101/128

NTB17-034b

25. Move the shift selector to P, then select Next.

Step
25

Figure 13
26. Operate the shift selector per the on-screen instructions.
a. Move the shift selector; P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.
27. Select Next.

Step
26

Step
27

Figure 14

102/128

NTB17-034b

28. Find the TCM Part Number (see Figure 15) and write it on the repair order.
NOTE: This is the current Part Number (P/N).

Step
28

Step
31

Figure 15

29 Compare the P/N you wrote down to the numbers in the Current ECM Part Number
column in Table B below.

30. Comparison results:


If there is a match, continue with the reprogramming procedure.



If there is not a match, reprogramming is not needed. Skip to ERASE MEMORY
DATA on page 115.

Table B
MODEL

CURRENT TCM PART NUMBER: 31036 -

2014 Sentra

9AM2A, 9AM2B, 9AM2C, 9AM9E, 9AM9D

31. Select Save.

103/128

NTB17-034b

32. Use arrows (if needed) to view and read all precautions.
33. Check the box confirming the precautions have been read.
34. Select Next.

Step
32

Step
33

Step
34

Figure 16
35. Read the Current Part Number and Part Number After Reprogramming. They
should be different.
36. Select Next.

Step 35
These numbers
should be
different

Step
36

Figure 17
104/128

NTB17-034b

37. Make sure OK is highlighted green (battery voltage must be between 12.0 and 15.5
Volts).

38. Select Next.

IMPORTANT: Battery voltage must stay between 12.0 and 15.5 Volts during
reprogramming or TCM reprogramming may be interrupted and TCM may be damaged.

Monitor battery
voltage here

Step
37
Step
38

Figure 18

105/128

NTB17-034b

NOTE: In the next step, the reprogramming process will begin when Start is selected.
39. Select Start.

Monitor battery
voltage here

Step
39

Figure 19
40. Wait for both progress bars to complete.

Step
40

Figure 20
106/128

NTB17-034b

41. When the screen in Figure 21 displays, the reprogramming is complete.
NOTE: If the screen in Figure 21 does not display (which indicates reprogramming did
not complete), refer to the information on the next page.
42. Disconnect the battery charger (GR8) from the vehicle.

43. Select Next.

Step
43

Figure 21

NOTE: Additional steps/operations are required before C-III plus will provide the
final reprogramming confirmation report. Continue with the reprogramming
procedure on page 109.

107/128

NTB17-034b

If reprogramming does not complete and the “!?” symbol displays as shown in
Figure 22:


Check battery voltage (12.0 –
15.5V).



Ignition ON, engine OFF.



External Bluetooth® devices are
OFF.



All electrical loads are OFF.



Select Retry and follow the on
screen instructions.
NOTE: Retry may not go
through on first attempt and can
be selected more than once.

Figure 22

If reprogramming does not complete and the “X” symbol displays as shown in
Figure 23:


Do not disconnect the plus VI
or shut down C-III plus if
reprogramming does not
complete.



Check battery voltage (12.0 –
15.5V).



CONSULT A/C adapter is
plugged in.



Ignition ON, engine OFF.



Transmission in Park.



All C-III plus / plus VI cables are
securely connected.



All C-III plus updates are
installed.



Select Home, and then restart
the reprogram procedure from
the beginning.

Figure 23

108/128

NTB17-034b

44. Confirm the Transmission Fluid temperature judgment is OK, then select Next.


If the judgment is NG, drive the vehicle to warm the transmission until the judgment
changes to OK.

Step
44

Figure 24

109/128

NTB17-034b

45. Follow the on-screen
instructions; maintain
the following conditions:
a. Parking brake set.
b. Ignition ON, with the
engine OFF.
c. Press the Brake.
d. Press accelerator
between ¼ and ½.
e. Put shift selector in
R.

Step
46

Figure 25

46. Select Erase DTC.

47. Follow the on-screen
instructions; maintain
the following conditions:
Step
48

a. Parking brake set.
b. Ignition ON, with the
engine OFF.
c. Fully depress the
accelerator.
d. Put shift selector in
R.
48. Select Start.
Figure 26

110/128

NTB17-034b

49. When COMPLETED is displayed, select Next.

Step
49

Figure 27

50. Operate the ignition per the on-screen instructions.

Ignition status

Timer

Progress display

Figure 28

111/128

NTB17-034b

51. When OK is displayed, select Next.

Step
51

Figure 29
52. Operate the shift selector per the on-screen instructions.
a. Move the shift selector to P; then move P>R>N>D>P
b. Confirm the center display meter indicates the correct selector position.
53. Select Next.

Step
53

Step
52

Figure 30

112/128

NTB17-034b

54. Erase all DTCs as follows:
a. Turn the ignition OFF.
b. Turn the Ignition ON.
c. Wait for DTC erase to complete.

55. Select Next.

Turn ignition ON > OFF > ON
ON

Step
55

Figure 31

113/128

NTB17-034b

56. Verify the before and after part numbers are different.
57. Print a copy of this screen (Figure 32) and attach it to the repair order.
58. Select Confirm.

Step
56

Step
57

Step
58

Figure 32

NOTE: If you cannot print the above screen:
a. Select Screen Capture.
b. Name the file.
c. Save the file in My Documents.


A copy of the screen is now saved in the CONSULT PC. It can be retrieved and
printed at a later time.

114/128

NTB17-034b

ERASE MEMORY DATA

59. Navigate C-III plus to the screen shown in Figure 33.


Diagnosis (All Systems) > TRANSMISSION > Work support

60. Select ERASE MEMORY DATA.

61. Select Start.

Step
60

Step
61

Figure 33

115/128

NTB17-034b

62. Follow the on-screen
instructions; maintain
the following conditions:
Step
63

a. Parking brake set.
b. Ignition ON, with the
engine OFF.
c. Fully depress the
accelerator.
d. Put shift selector in
R.
63. Select Start.
Figure 34

64. When the Current status
changes to
COMPLETED, select
End.

Step
64

Figure 35

116/128

NTB17-034b

CONFORM CVTF DETERIORTN
65. Navigate C-III plus to the screen shown in Figure 36.


Diagnosis (All Systems) > TRANSMISSION > Work support

66. Select CONFORM CVTF DETERIORTN.
67. Select Start.