Reference:

Date:

NTB17-029

March 14, 2017

VOLUNTARY SERVICE CAMPAIGN
2014-2017 TAXI AND 2013-2017 NV200
CENTER CONSOLE INSULATOR

PM674
CAMPAIGN ID #:
APPLIED VEHICLE: 2013-2017 NV200 (M20)
2014-2017 Taxi
Check Service COMM to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting a voluntary service campaign on certain specific 2014-2017 Taxi and
2013-2017 NV200 vehicles to install a center console insulator. This service will be
performed at no charge to owners for parts or labor.

IDENTIFICATION NUMBER
Nissan has assigned identification number PM674 to this campaign. This number must
appear on all communications and documentation of any nature dealing with this campaign.

DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.

Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/24

Repair Overview
Check Service COMM campaign ID # PM674
to confirm the vehicle you are working on
requires this campaign.

Does the air bag warning light:


Remain on after approximately 7 seconds.



Flash intermittently.



Not come on at all.

NOTE: When the air bag light operates correctly, it
will light for approximately 7 seconds and then turn
OFF.
YES

NO

Install Insulator-Console
Service Kit

Install Insulator-Console
Service Kit

Replace the Diagnostic
Sensor Unit

Check for stored DTCs
with CONSULT III plus

Are any DTCs stored?
YES

NO

 Go back to ASIST for further
diagnostic information.

Procedure complete

 Diagnosis and repairs beyond
replacement of the Diagnostic
Sensor Unit are not covered by
this campaign.

2/24

NTB17-029

SERVICE PROCEDURE
1. Confirm that the air bag warning light indicates that the system is operating correctly as
follows:
a. Turn the ignition ON, engine OFF.
b. Are any of the following conditions present?




The air bag warning light remains on after approximately 7 seconds.
The air bag warning light flashes intermittently.
The air bag warning light does not come on at all.

NOTE: When the air bag light operates correctly, it will light for approximately 7
seconds and then turn OFF.
c. Note the condition of the air bag warning light on the repair order (this will be used
later in this procedure) and then proceed to step 2.
d. Turn Ignition OFF.
For steps 2-5 refer to the Electronic Service Manual (ESM), section INT – Interior for
removal information, and Figure 1 for component locations.
WARNING: The metal brackets that support the following components are very sharp.
Take care when working around them.
2. Remove the parking brake finisher.
3. Remove the center console side finisher (LH and RH).

Figure 1
1. Center console tray
4. Center console front bracket
7. Center console rear finisher
10. Center console bin
13. Power socket (if equipped)

2. Center console side finisher (RH)
5. Center console center bracket
8. Center console assembly
11. Parking brake finisher
3/24

3. Center console side finisher (LH)
6. Center console rear bracket
9. Center console bin brace
12. USB connector (if equipped)
NTB17-029

4. Remove the center console “plastic
piece” shown in Figure 2 as follows:


Plastic piece located under the
parking brake lever.
Plastic piece

Figure 2

Cut through
center
a. Cut through the center of the plastic
piece with an appropriate tool.

Plastic piece
Figure 3

b. Remove the plastic piece from both
sides of the center console.


Already
removed

Remove

Figure 4 shows example of the
one side already removed.

Figure 4
5. Remove the center console assembly.

4/24

NTB17-029

Separation of Center Console Tray

1. Remove the six (6) screws that attach the center console tray to the center console
assembly and then remove center console tray.


Two (2) screws from each side and two screws (2) from underneath.



Screws are Torx T20.

Center
console tray

Center console
assembly

Left side screws shown.

Figure 5

Right side screws shown.

View from bottom of center
console assembly.

5/24

NTB17-029

Parking Brake Finisher
Attach nine (9) foam pieces to the parking brake finisher as follows:
1. Attach two (2) foam pieces (one on each side) into the flat recesses above the clips of
the parking brake finisher, as shown in Figure 2A.


See Table A in the Parts Information and use foam piece #1.
 Remove adhesive backing strip and attach the foam with adhesive facing up.

2. Attach the next two (2) foam pieces (one on each side) to the curved recesses above
the clips of the parking brake finisher, as shown in Figure 3A.


See Table A in the Parts Information and use foam piece #2.
 Remove adhesive backing strip and attach the foam with adhesive facing up.

NOTE: In Figures 1A, 2A and 3A the left side is show. Right side is similar.

Parking brake
finisher

Figure 1A
Adhesive
facing up

Adhesive
facing up
Up

Foam
piece #1

Foam
piece #2

Figure 2A

Figure 3A
6/24

NTB17-029

3. Attach two (2) foam pieces (one on each side) to the parking brake finisher
one at a time as follows (Figure 4A).


See Table A in the Parts Information and use foam piece #3.
a. Remove the adhesive backing strip.
b. Center the foam piece on the parking brake finisher so that it is:
 Overlapping the two pieces of foam just attached (foam piece #1 and #2),
 And is just below the lip of the parking brake finisher.
c. Attach foam piece #3.
NOTE: In Figure 4A the left side is shown. Right side is similar.

Overlap

Attached
below this lip

Overlap foam
Piece #1

Foam
Piece #1

Overlap foam
Piece #2

Foam piece #3 centered and
overlapping both foam pieces
attached in steps 1 and 2.

Foam
Piece #2

Figure 4A

7/24

NTB17-029

Press the adhesive
down firmly
d. Roll the foam over to the back
side and press the adhesive
down firmly.

Figure 5A

e. Press the adhesive of foam
piece #3 into foam pieces
installed in steps 1 and 2 firmly.

Press the adhesive
down firmly

Figure 6A
NOTE: Figure 7A below is an example of foam pieces #1, #2 and #3 attached.
The other side is similar.
Parking brake
finisher

Figure 7A
8/24

NTB17-029

Lip
4. Attach one (1) foam piece (foam piece
#4) to the front of the parking brake
finisher as follows:


See Table A in the Parts Information
and use foam piece #4.

Install below
this point

NOTE: Foam piece #4 should overlap
both left and right side foam pieces
attached in step 2 when done.
Figure 8A

a. Remove the adhesive backing
strip.

Overlap

Lip

b. Center the foam piece on the
parking brake finisher so that it is:
 Overlapping the two pieces of
foam attached in step 2 (foam
piece #2),
 And is just below the lip of the
parking brake finisher.
c. Attach foam piece #4.

Foam
Piece #4
Figure 9A

d. Roll the foam around to the back
side (shown in Figure 10A) and
press the adhesive down firmly.

Roll the foam
around to the
back side

Figure 10A

9/24

NTB17-029

e. Press the adhesive of foam piece
#4 into foam pieces installed in step
2 firmly.

Press the
adhesive
down firmly

Foam piece
installed in
step 2
Figure 11A

5. Attach two (2) foam pieces (foam piece
#5) one at a time, to each side of the
parking brake finisher as follows:


Overlap

Lip

See Table A in the Parts Information
and use foam piece #5.
a. Remove the adhesive backing
strip.
b. Attach the foam piece onto the
parking brake finisher so that it:
 Overlaps the piece of foam
attached in step 1 (foam piece
#1),

Foam
Piece #5
Figure 12A

 And is just below the lip of the
parking brake finisher.

Attach
to back
c. Twist foam piece 90 degrees and
attach to the back of the parking
brake finisher (Figure 13A).

Twist 90
degrees

Figure 13A

10/24

NTB17-029

d. Roll the foam around to the
back side of the parking brake
finisher (shown in Figure 14A)
and then press the adhesive
down firmly.

Attached to back side
Figure 14A

e. Press the adhesive of foam
piece #5 into foam pieces
installed in steps 1 firmly.
Press the
adhesive
down firmly

Foam piece
installed in
step 1

Figure 15A

11/24

NTB17-029

Center Console Side Finishers (LH and RH)

1. Attach two (2) foam pieces (foam piece #6) to the center console side finishers
one at a time as follows:


Attach where shown in Figures 1B and 2B and as shown in Figure 3B.



See Table A in the Parts Information and use foam piece #6.

LH center console side finishers

Attach foam
here

RH center console side finishers

Lip

Lip

Figure 1B

Attach foam
here

Figure 2B

Start foam so that it is
flush with this edge

a. Remove adhesive backing strip,
Lip

b. Start foam at the edge of center
console side finisher,

c. And then attach foam piece #6 below
lip.

Foam
Piece #6
Figure 3B

12/24

NTB17-029

Center Console Tray
Center console
tray
1. Attach one (1) foam piece (foam piece
#7) to the center console tray where
shown in Figure 2C as follows:


Foam
piece #7

See Table A in the Parts Information
and use foam piece #7.
a. Remove the adhesive backing
strip.

Start foam so
that it is flush
with this edge

Adhesive
facing side

b. Align foam piece #7 on either the
left or right side of the center
console tray so that it is flush with
the bottom edge (Figure 1C).
c. With the adhesive facing the side
of the center console tray,

Figure 1C

d. Attach foam piece #7 and continue attaching over the top of the center console
tray.
e. Finish with the opposite end of foam piece #7 flush with the opposite edge of the
center console tray as shown in Figure 2C.
Center console
tray

Foam piece #7

Figure 2C

13/24

NTB17-029

2. Attach two (2) foam pieces (foam piece
#8) one at a time to the center console
tray where shown in Figure 4C as
follows:


Center console
tray
Foam