Tundra
1 Remove disc brake anti-rust covers/anti-corrosion
wheel film*……………………………………………………..
2 Inspect tires for defects/damage ……………………………
3 Initialize Tire Pressure Warning System (TPWS)
(see page 2)…......................................................................
4 Install wheel covers/caps/spare tire wheel covers* ……….
5 Inspect for fuel, oil, coolant, and other fluid leaks …………
6 Inspect under the vehicle for damage, rust, etc ……………
7 Visually check bolts and nuts on chassis and powertrain
for looseness…………………………………………….
8 Install rubber body plugs (stored in glove box or center
console)*………………………………………………………..

2 Install antenna ………………………………………………

FUNCTIONAL OPERATION
Apply parking brake and cycle ignition “IG-ON”; place gear selector in reverse; turn
on lights and rear defogger. Unlock all doors, release fuel door.

5
6
7
8
9
10
11

OK

UNDER VEHICLE (ON HOIST)

1 Install Short Pin (see page 2) ……………..………………….

1
2
3
4

September 2015
Adjust\
Repair

OK

BEFORE INSPECTION

Adjust\
Repair

2016 PRE-DELIVERY SERVICE CHECK SHEET

Check dome, courtesy, map, and sun visor lights*………...
Check warning/indicator lights, gauges, and horn.…..…….
Check windshield wipers and washers….……………………
Check headlights, instrument lights, turn signals,
dimmer switch, emergency flashers, and brake lights …….
Check inside/outside rear view mirror operation/
adjustment*……………………………………………………..
Check cigarette lighter* and power outlets………………….
Check audio/navigation*/backup camera systems and
set clock.……………….……………………………………….
Install shift-lock override button cover ………... ……….…...
Check sliding roof* …………………………………………….
Check Rear Seat Entertainment System operation*……….
Check passenger airbag system cutoff switch and light* ….

ROAD TEST
A complete road test helps assure customer satisfaction. Drive vehicle over a
variety of road surfaces and driving conditions. Check for unusual noise and driving
performance.
Enter Odometer Readings
Reading Before Test: _______________ Reading After Test: ________________

1
2
3
4
5
6
7
8
9
10
11
12

WALKAROUND INSPECTION
Starting at the left front door, check window and door lock operation. Continue
around the vehicle in a counterclockwise direction checking each door and window
operation, child door locks, seat belts, interior condition, all lights, and luggage
compartment contents. Finish by checking headlight aim and continue into UNDER
HOOD checks.

1 Check door and door lock operation, including each
wireless remote control/theft deterrent system*…………….
2 Check window operation………………………………………
3 Check that engine starts with all keys ……………….………
4 Check that child safety door locks are in normal (unlocked)
position*…………………………………………………….….
5 Check seats and seat belt operation………………………...
6 Check rear defogger/rear view mirror defogger*…………..
7 Check side marker, tail, backup, cargo*, and license
plate lights ……………………………………………………..
8 Check jack and tool installation……………………………….
9 Check headlight aim…………………………………………...

Check cold engine operation …………………………………
Check engine operation during warm-up ……………………
Check engine at normal operating temperature ……………
Check transmission operation …………………………...….
Check brake and parking brake operation ………………….
Check steering operation and off-center/vehicle pull/flutter
Inspect for abnormal noise and vibration ……………………
Inspect for squeaks and rattles ………………………………
Check front and rear* heater and A/C operation……………
Check cruise control operation* ……………………………...
Check front seat heater/ventilation* operation ……………..
Set/calibrate compass* (see page 2)………………………..

FINAL INSPECTION AND CLEANING
1 Remove interior protective covers, unnecessary labels,
tags, etc. (Remove just before delivery to customer) ………
2 Visually inspect all interior parts for installation, damage, fit,
dirt, etc.…………………………………………………………..
3 Verify floor map application and install using retaining
clips*…………………………………………………………….
4 Remove Rapgard™ and clear protective bumper film*……
5 Wash and clean vehicle……………………………………….
6 Inspect paint finish for scratches, chips, rust, dents,
damage, etc……………………………………………………
7 Inspect exterior body parts for proper installation, damage,
rust, etc………………………………………………………….
8 Place oil change sticker on inside of windshield, top left
corner……………………………………………………………
9 Place Owner’s Guide and first aid kit portfolio* in glove box
10 Perform Techstream Health Check…………………………..
11 Install front license plate* (see page 2)………………………
12 Install receiver towing hitch cap*…….………………………..

UNDER HOOD
1
2
3
4
5

Check engine oil level…………………………………………
Check brake and power steering* fluid levels……..………..
Check engine coolant level …………………………………..
Check windshield washer fluid level…………………………
Check battery state-of-charge using Digital Battery
System Analyzer (SOC Reading: ___________%) ……
6 Inspect for fuel, oil, coolant, and other fluid leaks………….
* Inspect or install when equipped/required.

Completion and retention of this form is required to comply with Toyota’s Warranty Policy.
TECHNICIAN’S SIGNATURE

NAME (PLEASE PRINT)
Date

Dealer Name

SERVICE MANAGER’S SIGNATURE

We hereby certify that all items
on this form have been
checked and corrected for
proper operation as required.

NAME (PLEASE PRINT)
Dealer Code

Vehicle Identification Number (Sticker)

SHORT PIN INSTALLATION
To minimize battery discharge, the Short Pin has been removed and is
stored in the engine compartment Relay Block. Install the Short Pin and
perform the below procedure to clear the Slip Indicator Light.

1

Slip Indicator Light Clearing Procedure
1. Drive straight for a minimum of 3 seconds at a speed greater than 7
mph.
2. Gently maneuver through a moderate turn (steering wheel rotated at
least 20 degrees) lasting for at least 4 seconds at a speed greater than
7 mph.
3. Slip Indicator Light will turn OFF when the system has been
successfully initialized.
NOTE
Do NOT turn the steering wheel rapidly.

2
1 Storage Location

2 Installation Location

4. If the Slip Indicator Light remains ON, repeat steps 1 and 2.

TIRE PRESSURE WARNING SYSTEM (TPWS) INITIALIZATION
The Tundra is equipped with a direct-type TPWS. Each tire (including the spare) has a tire pressure warning valve/sensor that
measures tire pressure. The sensors must first be activated prior to operation. Please refer to the below information.
Refer to the Repair Manual for the Initialization procedure.
NOTE
To adjust the tire pressure correctly when the outside temperature is significantly colder than shop temperature,
perform a Health Check using Techstream and select the “Compensation Tire Pressure” checkbox. Compensation
pressures will be displayed on the Health Check results screen. Adjust the tire pressure when the tires are cold.

COMPASS CALIBRATION
Some Tundra vehicles are equipped with a compass in the rear view mirror. In order for the compass to correctly indicate the
direction the vehicle is heading, it must be calibrated prior to vehicle delivery.
Refer to the Repair Manual for the Calibration procedure.
NOTE
 Do NOT perform calibration of the compass in a place where the Earth’s magnetic field is subject to inferference
by artificial magnetic fields (underground parking, under a steel tower, between buildings, roof parking, near a
railroad crossing, etc.)
 During calibration, do NOT operate electric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.

FRONT LICENSE PLATE AND MOUNTING BRACKET INSTALLATION*
1. Insert the front license plate into tabs on the front license plate
mounting bracket.
2. Align the installation holes on the license plate and front license
plate mounting bracket with the dimples on the front bumper.

3

3. Screw the 2 self-tapping screws directly into the dimples to install
the front license plate and front license plate mounting bracket.
NOTICE
.

 Do NOT pre-drill holes into the bumper.
 Do NOT overtighten the self-tapping screws.
HINT
Tighten the self-tapping screw into the round hole side
first, then tighten the other self-tapping screw into the
slotted hole.

1
4
1 License Plate
2 License Plate Mounting
Bracket

3 Dimples
4 Self-tapping Screws