23.

18) Stand by as the key is registered.
Note:
When an error screen is displayed, refer to No. 4 in
"4-3 Correspondence table when registration is not
possible".

Caution:
If you have no more keys to be registered, make
sure to click the [Cancel] button to quit the
registration operation.
If you quit the operation without clicking the
[Cancel] button, the immobilizer indicator
blinks differently than usual. In such a case,
register the immobilizer again.

IM-00418

IM-00418

19) The screen shown below will appear if
registration ends normally. If you have another
key to be registered, click the [OK] button. If you
do not have any more keys to be registered,
click the [Cancel] button and advance to step
23.

IM-00420

Caution:
If you have no more keys to be registered, make
sure to click the [Cancel] button to quit the
registration operation.
If you quit the operation without clicking the
[Cancel] button, the immobilizer indicator
blinks differently than usual. In such a case,
register the immobilizer again.

IM-00420

22) Repeat steps 15 through 18.
23) The remote control engine starter registration
mode confirmation dialog box will be displayed.
If you have another key to be registered, click
the [OK] button. If you do not have any more
keys to be registered, click the [Cancel] button
and move on to step 26.
Note:
The screens shown in this section may be different
depending on the model being used. In such a
case, follow the instructions shown on the screens.

IM-00419

IM-00419

20) Repeat steps 15 through 18.

IM-00421

9

Vehicle-id:
SIE-id::
Å`

S1001BE.fm

10 ページ

２０１４年４月３０日

水曜日

午後２時９分

A type
REGISTRATION MANUAL FOR IMMOBILIZER

24) Wait until the remote control engine starter is
then being registered.
Note:
When an error screen is displayed, refer to No. 5 in
"4-3 Correspondence table when registration is not
possible".

IM-00422

IM-00422

25) The screen shown below will appear if
registration ends normally. Click the [OK]
button.

R emote engine s tart R egistration successful
Turn off the engine
IM-00423
And con firm res tart engine

Press OK

IM-00423

26) After confirming that the keyless access with
push button start system and remote control
engine starter operate normally, quit the
registration operation.

10

Vehicle-id:
SIE-id::
Å`

２０１５年７月３０日

木曜日

午後４時０分

Vehicle-id:
SIE-id::
Å`

11

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

ECM

X

X

X

X

X

All

X

X

X

X

X

X

X

X

X

X

X

X

Body
integrated
unit

Parts failed/lost

X

X

X

X

X

X

X

X

X

X

X

X

Meter *4
or
Security CU
*5

New key you want to register

Keys you want to register (registered key or new key) (*1)

Keys you want to register (registered key or new key) (*1)

New key you want to register

New key you want to register

New key you want to register

Keys you want to register (registered key or new key) (*1)

Keys you want to register (registered key or new key)

Keys you want to register (registered key or new key) (*1)

Keys you want to register (registered key or new key) (*1)

All registered keys

Keys you want to register (registered key or new key) (*1)

New key you want to register

New key you want to register

New key you want to register

All registered keys

Keys you want to register (registered key or new key) (*1)

Keys you want to register (registered key or new key)

All registered keys

Keys you want to register (registered key or new key) (* 1)

All registered keys

New key you want to register

Keys you want to register (registered key or new key)

Key

X
X

X

X

X

X

X

X

X

X

X

X

X

Body
integrated
unit

X

X

X

X

X

X

X

X

X

X

X

ECM

Parts required to replace or prepared when items on the left fail

*1: When the body integrated unit is replaced, a new key must be used.
The models that require a new key are following:
•LEGACY, OUTBACK (2005MY to 2009MY)
•IMPREZA (2008MY to 2010MY)
•FORESTER (2009MY to 2010MY)
•TRIBECA (From 2006MY)
*2: The registration work cannot be performed in the current state. The security ID must be written. Contact your Subaru service
representative.
*3: If you have lost your security ID, please contact your Subaru service representative.
*4: Without security CU
*5: With security CU

4 parts
failure

3 parts
failure

2 parts
failure

1 parts
failure

X

Not all

Key

Note:
To register an immobilizer, your security ID is required. (*3)

1. Parts replacement table

X

X

X

X

X

X

X

X

X

X

X

X

Meter *4
or
Security CU
*5
(1)

Registering Immobilizer Key

(*2)

(*2)

(*2)

(*2)

Registering Immobilizer Key

Registering Immobilizer Key

(*2)

Registering Immobilizer Key

Registering Immobilizer Key

(*2)

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

Registering Immobilizer Key

(2)

Procedures to perform after parts replacement

Registering Immobilizer Key

4-2 Immobilizer system: Correspondence table at the time of parts lost or failure

S1001BE_V2.fm 11 ページ

A type
REGISTRATION MANUAL FOR IMMOBILIZER

12 ページ

２０１４年４月３０日

水曜日

午後２時９分

Vehicle-id:
SIE-id::
Å`
Error screen

→ "Do you want to register the
Engine ECM?" → "Engine ECM
Initializing communication..."

→ "Key has been registered"

2

3

4

Action to be taken

12
ECM failure
ECM failure

EGI unit NG

ECM failure

NG EGI-SSM Communication

NG EGI unit EEPROM

•Subaru Select Monitor failure
•ECM failure

NG EGI security access NG

Body integrated unit failure

Mode did not end normally last time

This key has been already registered.

NG IMM Control Module EEPROM

Transponder failure

Transponder failure

Check version of Subaru Select Monitor.
Replace the ECM.

Immobilizer antenna failure

NG Antenna

NG Key Communication Failure

Immobilizer antenna failure

Press the Cancel button that appears to recover normally.

ECM failure

EGI unit NG

NG Antenna

Perform the diagnosis for DTC B1570 (P1570).

Body integrated unit failure

NG IMM Control Module EEPROM

NG Key Communication Failure

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the battery.

ECM failure

NG EGI unit EEPROM

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the battery.

Wait until the self shut completes, and retry the procedure.
When the same error is indicated again, remove and install the battery.

Perform the diagnosis for DTC B1577 (P1577).