.'

NUMBER:

25-001 -13 REV. A

GROUP:

Emissions Control

DATE:

May 10, 2013

This bulletin is supplied as technical infonnation only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system,
or transmitted, in any fonn or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of Chrysler LLC.

THIS BULLETIN SUPERSEDES SERVICE BULLETIN 25-001-13, DATED JANUARY 29,
2013, WHICH SHOULD BE REMOVED FROM YOUR FILES. ALL REVISIONS ARE
HIGHLIGHTED WITH **ASTERISKS** AND INCLUDE ADDITIONAL MODEL YEARS,
UPDATED PART NUMBERS, AND SIMPLIFIED DIAGNOSTICS.

SUBJECT:
MIL Illumination Due to P2000, P2AOO and/or P2A01
OVERVIEW:

This bulletin involves inspecting both Oxygen (02) sensors and either cleaning or
replacing the sensors and installing an 02 Sensor Heat Shield on the exhaust pipe in the
area of the FRONT 02 sensor.

MODELS:
(D1)

Ram Truck 3500

2010 - **2011 ** (D2)

Ram Truck 3500

2007 - 2009

(DH)

Ram Truck 2500

2010 - **2011 ** (DJ)

Ram Truck 2500

2007 - 2009

NOTE: This bulletin applies to vehicles equipped with a 6.7L Cummins diesel engine
(sales code ETJ) built before **August 2, 2010 (MDH0802XX)**.

SYMPTOM/CONDITION:
Customer may experience MIL illumination. Further investigation by the technician may
find one or more of the following DTC(s) present:
•
•
•

P2000 - NOX Absorber Efficiency Below Threshold - Bank 1.
P2AOO - 02 Sensor 1/1 Circuit Performance .
P2A01 - 02 Sensor 1/2 Circuit Performance.

DIAGNOSIS:
1. **Complete a Diesel Diagnostic Worksheet per instructions in Service Bulletin
18-045-11 Dated October 19, 2011 and U. S . Warranty Bulletin D-11-55 Dated
October, 2011. All DTC's need to be recorded on the WRO and DTC's other than the
ones listed above may require additional diagnosis and repair after completing this
Bulletin.

..

;

25-001-13 REV. A

-2-

NOTE: 02 sensor fouling may be related to other components that can cause
increase sooting. Follow the procedures provided in
DealerCONNECT>TechCONNECT>Service lnfo>Group 28 OTC Based
Diagnostics>Module, Engine control (ECM), 6.7L>Standard
Procedure>PRE-DIAGNOSTIC TROUBLE SHOOTING PROCEDURE, 6.7L or
DealerCONNECT>TechCONNECT>Service lnfo>Group 29 Non-OTC
Diagnostics>Drivability - Diesel, 6.7L>Diagnosis and
Testing>PRE-DIAGNOSTIC TROUBLE SHOOTING PROCEDURE, 6.7L before
proceeding with this bulletin.

2. Inspect the front 02 sensor area of the exhaust for the presence of either a wrap or
blanket (Fig. 1 ).

Fig. 1 02 SENSOR WRAP
1 - 02 SENSOR WRAP

Is there a wrap or blanket around the exhaust pipe in the area of the front 02 sensor?
a. YES>>>Proceed to the next step.
b. NO>>>Proceed to the Repair Procedure.
4. Was the wrap/blanket installed properly and is not damaged or torn/tattered?
a. YES>>>This bulletin will not address the symptom/condition. Follow the diagnostic
information provided in DealerCONNECT>TechCONNECT>Service lnfo>Group 28
OTC Based Diagnostics>Module, Engine control (ECM), 6.7L>Standard
Procedure>PRE-DIAGNOSTIC TROUBLE SHOOTING PROCEDURE, 6.7L or
DealerCONNECT>TechCONNECT>Service lnfo>Group 29 Non-OTC
Diagnostics>Drivability - Diesel, 6.7L>Diagnosis and Testing>PRE-DIAGNOSTIC
TROUBLE SHOOTING PROCEDURE, 6.7L.
b. NO>>>Proceed to the Repair Procedure.**
3.

-3-

25-001-13 REV. A

PARTS REQUIRED:

Qty.

Part No.

Description

AR (2)

05149263AA

Oxygen Sensors (Do not use earlier versions of 02
sensor when performing this repair. Ensure part
number is 05149263AA or higher level).

1

68102274AA

Kit, 02 Sensor Heat Shield

**AR (1)

52121859AD

Clamp, Band - 2010 and 2011 MY only and only until
kit 68102274AB or later is available.**

REPAIR PROCEDURE:
1. Raise the vehicle on a hoist.
2. If the vehicle is already equipped with a wrap or blanket but this bulletin is being
performed because they are damaged, remove the damaged wrap or blanket from the
exhaust pipe.
3. Remove both upstream and downstream Oxygen (02) sensors.
4. Remove the exhaust pipe. Refer to the procedures identified in
DealerCONNECT>TechCONNECT>Service lnfo>11 - Exhaust System>PIPE,
Exhaust>Removal>6.7L DIESEL for additional information.
5. Install heat shield (p/n 68102274AA). Refer to the procedures identified in the
Instruction Sheet (p/n K6855747) for additional information.
NOTE: **The 02 sensor heat shield kit P/N 68102274AA contains band clamp P/N
52121859AC. 2010 and 2011 Model year trucks must use a heavier duty
clamp. This clamp part number is 52121859AD. The 02 sensor heat shield kit
will soon be updated to supersede from P/N 52121859AC to 52121859AD.
Once the kit has been updated, it will no longer be necessary to order
turbocharger band clamp 52121859AD separately. Any 02 sensor heat shield
kit P/N 68102274AB and beyond will have the updated clamp.**

6.

7.

Install the exhaust pipe. Refer to the procedures identified in
DealerCONNECT>TechCONNECT>Service lnfo>11 - Exhaust System>PIPE,
Exhaust>lnstallation>6.7L DIESEL for additional information.
Inspect both 02 sensors to ensure that the latest sensors are installed in the vehicle.
02 sensors that have p/n 05149263AA (or later) scribed on the sensor, (Fig. 2) are the
newer style sensor. If it is difficult to read the part number, the newer style sensor can
easily be identified by the soot shield design on the sensor, (Fig. 3).

-4-

25-001-13 REV. A

05149263AA

8201aQ85

Fig. 2 02 SENSOR PART NUMBER LOCA T/ON
1 - 02 SENSOR PART NUMBER

8201o084

Fig. 3 02 SENSOR OLD VERSUS NEW
1 - EARLY STYLE SOOT SHIELD (OLD SENSOR)
2 - NEW STYLE SOOT SHIELD (NEW SENSOR)

-58.

25-001-13 REV. A

If the oxygen sensor is not scribed with p/n 05149263AA or newer or if the soot shield
appears as the older style soot shield (as seen in (Fig. 3)), replace the oxygen sensors
with p/n 05149263AA. If the oxygen sensors are to be reused , clean the 02 sensor
using shop air only. Do not use any solvents or cleaners when cleaning the 02
sensor. Torque to 41 N•m (30 ft. lbs). Connect wiring to both of the Oxygen (02)
sensors.

POLICY:
Reimbursable within the provisions of the warranty.
TIME ALLOWANCE:
Labor Operation
No:
25-01-70-90

Description

Amount

Shield, 02 Sensor - Install and Either Clean
and/or Replace 02 Sensors (2 - Skilled)

1.7 Hrs.

Remove 02 Sensor Wrap and Clean Exhaust
Pipe (2 - Skilled)

0.2 Hrs.

Optional Procedure
25-01-70-94

FAILURE CODE:

lzz

IService Action