Hyun a R 11

nEWTHlnKlnG.
nEW POSSIBILITIES.

Technical Service Bulletin

GROUP
CAMPAIGN

NUMBER
14 01 063

1 - - - - -- - - -- - - - - i - -- - -

DATE
DECEMBER 2014

-- - - - - j

MODEL(S)
ELANTRA (MD/UD)

ECM UPDATE - OTC P2096 (SERVICE CAMPAIGN TW3)

SUBJECT:

ECU Update
*IMPORTANT

*** Retail Vehicles Only***
Dealers must perform this Service Campaign whenever an affected vehicle is in the shop for any
maintenance or repair.
When a vehicle arrives at the Service Department, access Hyundai Motor America's "Warranty
Vehicle Information" screen via WEBDCS to identify open Campaigns .

Description: This bulletin provides an ECM update for some 2013MY Elantra vehicles to update the
diagnostic logic for OTC P2096 [Post Catalyst Fuel Trim System too Lean (Bank1 )] .

Applicable Vehicles: 2013 ELANTRA (MD/UD)

GOS Information:
"330. UD/MD 1.8MPI ENGINE OTC P2096 IMPROVEMENT"
NOTE: The ECM Update S/W is only available on the PC based GOS.

Warranty Information:

40C083RO

ECM UPGRADE

0.3 M/H

NOTE: Submit Claim on Campaign Claim Entry Screen.

Circulate To : General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors , Technicians , Body Shop Manager, Fleet Repair

ECM UPDATE- OTC P2096 (SERVICE CAMPAIGN TW3)

SUBJECT:

ECM ROM ID INFORMATION TABLE:
Verify the ECM ROM ID before updating the vehicle 's software. Refer to the table below.

-....., • ' ,L.-

~

MY

~.

Emission

).

ECM P/N

T/M

IMMO

11.

-

-

'

n

Previous
'

r

39101-2EMA3
(UD)
YES
(Start-Stop
Button)
39101-2EMN3
(MD)

SU LEV

NO
(Key Start)

New

I....!

~

,. "

MD3SP1 MS2D2A
MD3SP1 MS2D2B
MD3SP1 MS2D8A
MD3SP1 MS2E3A
MD3SP1 MF2EAA
MD3SP1 MS2D2A
MD3SP1 MS2D2B
MD3SP1 MS2D8A
MD3SP1 MS2E3A
MD3SP1 NS2D2A
MD3SP1 NS2D2B
MD3SP1 NS2D8A
MD3SP1 NS2E3A
MD3SP1 NF2EAA

39103-2EMN3
(MD)

MD3SP1 NS2D2A
MD3SP1 NS2D2B
MD3SP1 NS2D8A
MD3SP1 NS2E3A

39101-2EMB3
(UD)

MD3UP1 MS2D2A
MD3UP1 MS2D2B
MD3UP1 MS2D8A
MD3UP1 MS2E3A

AT

ULEV

~

AT
39103-2EMA3
(UD)

13MY

~~-

ROMID

YES
(Start-Stop
Button)

MD3UP1 MF2EAA

39101-2EMP3
(MD)

MD3UP1 MS2D2A
MD3UP1 MS2D2B
MD3UP1 MS2D8A
MD3UP1 MS2E3A

39103-2EMB3
(UD)

MD3UP1 NS2D2A
MD3UP1 NS2D2B
MD3UP1 NS2D8A
MD3UP1 NS2E3A
AT

39103-2EMP3
(MD)

39107-2EMB3
(MD/UD)

TSB # : 14-01-063

NO
(Key Start)

MT

MD3UP1 NS2D2A
MD3UP1 NS2D2B
MD3UP1 NS2D8A
MD3UP1 NS2E3A

MD3UP1 NF2EAA

MD3UP1 NS2D2A
MD3UP1 NS2D2B
MD3UP1 NS2D8A
MD3UP1 NS2E3A

Page 2 of 5

SUBJECT:

ECM UPDATE- OTC P2096 (SERVICE CAMPAIGN TW3)

GENERAL PRECAUTIONS:
•
•

Connect the USB cable between the GOS and
the VCI.
Connect the 16-pin DLC connector from the
VCI into the DLC located under the driver's
side dash .
USB Cab le

Make sure the battery icon at the bottom right of the GOS laptop shows at least 50 %; if not,
charge the GOS or attach a battery charger.
•

Turn off all lights (Do not leave the headlight switch in auto mode) and all accessories
(including heater/air conditioner/fan , audio , heated seats , rear defroster, etc) to ensure the
battery will not be discharged during the update .

•
•

Perform the update with the ignition key in the ON position . (Turn the ignition key to ON
position or press the Start-Stop Button two times without depressing the brake pedal) .
Do not disconnect any cables connected to the vehicle or the GOS during the update .

•

Do not start the engine or turn the ignition switch OFF during the update .

Confirm your GOS has the most recent version . If not, connect the GOS to an Internet port,
open the GOS home page and select "Update". Refer to instructions on hmaservice .com if
necessary.
If you encounter GOS related problems , call the GIT Helpline at 888-437-0308.

SERVICE PROCEDURE:
GOS AUTO MODE ECM UPDATE PROCEDURE
1.
2.
3.

From the GOS home page , select ECU Upgrade. If necessary, select the VIN .
Select Engine as the system and then select OK.
Select Auto Mode and then select Next.

TSB # : 14-01-063

Page 3 of 5

SUBJECT:
4.

ECM UPDATE - DTC P2096 (SERVICE CAMPAIGN TW3)

From the System tab , select Engine and then select OK. The GOS will read the ROM ID .
Confirm the ROM is applicable as shown on Page 2-3, "ECM ROM ID Information".
NOTE: Record the ECM ROM ID in case the auto update fails and a manual update is needed .

GOS ~
~

5.

Update event "330. UD/MD 1.8MPI ENGINE OTC P2096 IMPROVEMENT" will display.
Select Upgrade.
PreparaUon

( -

• Mode
Auto Mod.

EventGroup

• CurrentROMIO

Repa ir

EYlnlLill

~Ulll'1NS2E3A

'* Latest ROM ID

•System
ENGINE

a Event selection
1. Revtcw and understand related TSB for vehicle reprogramming .
2. Select reprogramming event from Upgrade Event pull do'tllrTl menu above.
3. Click the Upgrade button to begin ECU upgrade .

6.
7.
8.
9.
10.
11.
12.

If the screen indicates "Voltage is OK" (voltage > 12volts), select OK. If not, select CANCEL
and charge the vehicle battery by running the engine for 10 minutes .
Updating will occur until 100% is reached on the bar graph . At the prompt, turn the ignition key
OFF for 10 seconds , then turn it ON and select OK.
The GOS will confirm that ECM reprogramming is successfully finished . Select OK.
If the ECM update was not successful, go to GOS MANUAL MODE ECM UPDATE
PROCEDURE.
Check for OTC in all systems and Erase All OTC that stored due to loss of CAN communication
during the ECM Update.
Turn OFF ignition for 10 seconds then turn ON before going to engine start.
Start the engine to confirm proper operation .

In the event of AUTO MODE update failure :
• You must attempt MANUAL MODE. Use the ECM P/N from the vehicle's ECM
label if it is not clear from the ROM ID Table as to the correct ECM P/N to use for
your vehicle.
• Replacing an ECM without carefully documenting that a MANUAL MODE update
attempt was made may result in claims charged back.

TSB # : 14-01-063

Page 4 of 5

ECM UPDATE - OTC P2096 (SERVICE CAMPAIGN TW3)

SUBJECT:

GOS MANUAL MODE ECM UPDATE PROCEDURE

•
•
•
•

GOS Manual Mode is intended for recovery of an ECM Update should it begin but
then later fail in process in the Auto Mode .
The ECM connectors must be disconnected for 15 minutes to reset its contents
then perform this Manual Mode Update.
Do not force Manual Mode if you get an error in Auto Mode that the vehicle 's
current ROM ID did not apply.
It is critical to identify the correct ECM Part Number in the PASSWORD table or the
ECM may be permanently damaged . It is recommended to remove ECM and read
the part number from the label to confirm.

1.

From the GOS home page , select ECU Upgrade . If necessary, select the VIN.

2.

Select Engine as the system and then select OK.

3.
4.
5.

Select Manual Mode and then select Next.
From the System tab , select Engine and then select OK.
Select update event "330. UD/MD 1.8MPI ENGINE OTC P2096 IMPROVEMENT", then select

6.

Next.
Be certain to select the exact appropriate ECU of the vehicle, select Upgrade , enter
corresponding password from the table below and select OK.

KEY TYPE

PASSWORD

UD/MD 1.8 AT IMMO: 39101-2EMA3/2EMN3

Start-Stop Button

0128

UD/MD 1.8 AT,MT IMMO: 39101-2EMB3/2EMP3

Start-Stop Button

0129

UD/MD 1.8 AT NON IMMO 39103-2EMA3/2EMN3

Key Start

0130

UD/MD 1.8 AT,MT NON IMMO: 39103-2EMB3/2EMP3 , 39107-2EMB3

Key Start

0131

MENU

7.

The remaining steps are the same as Steps 6-12 of the Auto Procedure.

TSB # : 14-01-063

Page 5 of 5