Page 1 of 6

SB-10057583-3378
TECHNICAL BULLETIN
K245 UPS5314-4bNAS1
09 OCT 2014

© Jaguar Land Rover North America, LLC
NOTE: The information in Technical Bulletins is intended for use by trained, professional Technicians with the knowledge, tools, and equipment required to
do the job properly and safely. It informs these Technicians of conditions that may occur on some vehicles, or provides information that could assist in
proper vehicle service. The procedures should not be performed by 'do-it-yourselfers'. If you are not a Retailer, do not assume that a condition described
affects your vehicle. Contact an authorized Jaguar service facility to determine whether this bulletin applies to a specific vehicle.

Changes are highlighted in gray

SECTION: 205-01

Update Prior to Sale: Driveshaft Fixings
AFFECTED VEHICLE RANGE:
XJ Range (X351)
Model Year:
VIN:

2014
V71369-V71498

Engine:

V6 S/C 3.0L Petrol

MARKETS:
NAS

CONDITION SUMMARY:
This Update Prior to Sale notice has been amended to include sold vehicles.
Situation: A potential issue has been identified on a number of 2014 model year XJ (X351) vehicles, fitted with the 3.0L V6
supercharged engine only, where the driveshaft fixings may not have been tightened to the correct torque value.
Action: Retailers are required to HOLD only affected vehicles that are within your control and refrain from releasing the vehicles for new
or used vehicle sale pending completion of the rework action detailed in this Technical Bulletin. Unsold vehicles should have this
performed as part of the Pre-Delivery Inspection (PDI) process but must have it completed prior to vehicle handover to the customer.
Affected vehicles already in the hands of customers should be updated at the next available opportunity

PARTS:

NOTE: * when ordering parts, order only the expected percentage demand of parts identified
DESCRIPTION
Bolt

PART No. / SUNDRY CODE
C2D2087

QTY. / VALUE
12

EXPECTED % of VEHICLES REQUIRING PARTS*
100

SPECIAL TOOLS:
Refer to Workshop Manual / Service Instruction for any required tools

WARRANTY:

NOTE: Check DDW to ensure that a vehicle is affected by this program prior to undertaking any rework action. Repair
procedures are under constant review, and therefore times / prices are subject to change; those quoted here must be taken as
guidance only. Refer to TOPIx to obtain the latest repair time. At the time of confirming a booking for vehicle repair, ensure
that all outstanding Service Actions are identified to ensure the correct parts are available and adequate workshop time is
allocated for repairs to be completed at one visit.

Warranty claims must be submitted quoting Program Code 'K245' together with the relevant Option Code from the table. The SRO and part
information listed have been included for information only. The Option Code(s) that allows for the drive in / drive out allowance may only be
claimed if the vehicle is brought into the workshop for this action alone to be undertaken.

This program is valid for a limited time only. Warranty claims with a repair date prior to the 16 March 2015 closure date must be submitted
for payment within 30 calendar days of completion of the repair.
PROGRAM CODE OPTION CODE

DESCRIPTION

SRO

TIME (HOURS) PARTS / SUNDRY CODE QTY. / VALUE

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014

Page 2 of 6

K245

B

Driveshaft fixings - Renew

47.91.17

1.90

C2D2087

12

K245

C

Driveshaft fixings - Renew
Drive in/drive out

47.91.17
10.10.10

1.90
0.10

C2D2087
-

12
-

Normal Warranty policies and procedures apply

SERVICE INSTRUCTION 'A':
Rear Wheel Drive (RWD) Vehicles Only

1. Open the floor console stowage compartment lid.

2. Remove the trim.

3. Release the emergency park release lever as shown.

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014

Page 3 of 6

4. Disengage the parking brake.

5. Disconnect the battery (see TOPIx Workshop Manual, section 414-01).

6.

WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety
stands.

Raise and support the vehicle on a wheel free lift.

7. Remove the exhaust system (see TOPIx Workshop Manual, section 309-00).

8.

NOTE: Retain the locators for use with the new retaining
bolts.

NOTE: Tighten the fixings in sequence directly across/180
degrees (criss-cross).

Install the six (6) new retaining bolts.
Torque: 75 Nm

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014

Page 4 of 6

9.

NOTE: Retain the locators for use with the new retaining
bolts.

NOTE: Tighten the fixings in sequence directly across/180
degrees (criss-cross).

Install the six (6) new retaining bolts.
Torque: 75 Nm

10. Reverse steps 1-7.

SERVICE INSTRUCTION 'B'
All Wheel Drive (AWD) Vehicles Only

1. Disconnect the battery (see TOPIx Workshop Manual, section 414-01).

2.

WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety
stands.

Raise and support the vehicle on a wheel free lift.

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014

Page 5 of 6

3. Remove the exhaust system (see TOPIx Workshop Manual, section 309-00).

4. Remove the retaining bolts and release the emergency park release lever
cable.

5. Release
the
emergency
park
release
lever.

6.

NOTE: Retain the locators for use with the new retaining
bolts.

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014

Page 6 of 6

NOTE: Rear Wheel Drive (RWD) shown; All Wheel Drive
(AWD) similar.

NOTE: Tighten the fixings in sequence directly across/180
degrees (criss-cross).

Install the six (6) new retaining bolts.
Torque: 75 Nm

7.

NOTE: Retain the locators for use with the new retaining
bolts.

NOTE: Tighten the fixings in sequence directly across/180
degrees (criss-cross).

Install the six (6) new retaining bolts.
Torque: 75 Nm

8. Reverse steps 1-5.

http://topix.jaguar.jlrint.com/topix/service/procedure/500216/ODYSSEY_FSA/G181763...

10/21/2014