SB-10045219-2096

Service Bulletin
Applies To:

12-015
May 22, 2012

2009–10 TSX – Check the iN VIN status for eligibility

Product Update: Roof Molding Is Loose
BACKGROUND
In high winds, the roof molding may lift in the middle,
allowing either its front or rear retention clip to come
loose.

WARRANTY CLAIM INFORMATION
Operation Number: 8140B2
Flat Rate Time:

0.3 hour

Failed Part:

P/N 74306-TL0-G01

CLIENT NOTIFICATION
All owners of affected vehicles will be sent a
notification of this product update. An example of the
client notification is at the end of this service bulletin.

Defect Code:

5NR00

Symptom Code:

S0500

Skill Level:

Repair Technician

Do an iN VIN status inquiry to make sure the vehicle
is shown as eligible.

NOTE: Do not submit the Konishi Bond as a
replacement part. Please submit under materials.
Since one tube of Konishi Bond repairs six vehicles,
the cost of the material should equal 1/6 of the dealer
net cost.

Some vehicles affected by this campaign may be in
your new or used vehicle inventory. These vehicles
must be repaired before they are sold.
CORRECTIVE ACTION
Apply Konishi Bond adhesive to the front and rear
retaining pins on the body. If a roof molding is
damaged or missing, install a new one.
PARTS INFORMATION
Left Side Roof Molding: P/N 74316-TL0-E00
Right Side Roof Molding: P/N 74306-TL0-E00

REPAIR PROCEDURE
1. Apply protective tape to the body.
1. Using the appropriate trim tool, slide the roof
molding rearward to release the front bracket from
the pin and pull up on the front portion of the
molding.
TRIM TOOL

2

PROTECTIVE
TAPE

REQUIRED MATERIALS
Konishi Bond: P/N 08713-0008
(one tube will repair about six vehicles)

1

ROOF
MOLDING
PIN

FRONT
BRACKET

2. Inspect the front bracket.
• If the bracket comes off the roof molding or the
molding is damaged, remove the molding and go
to step 6 to install a new roof molding.
• If the bracket is OK, go to step 4.

© 2011 American Honda Motor Co., Inc. – All Rights Reserved

BTB 47648 (1205)

1 of 3

CLIENT INFORMATION: The information in this bulletin is intended for use only by skilled technicians who have the proper tools, equipment, and
training to correctly and safely maintain your vehicle. These procedures should not be attempted by “do-it-yourselfers,” and you should not assume this
bulletin applies to your vehicle, or that your vehicle has the condition described. To determine whether this information applies, contact an authorized
Acura automobile dealer.

3. At the rear of the molding, pull up and release the
rear bracket from the pin.

6. Apply a 50 mm bead of Konishi Bond to the front
and rear pins as shown until the pins on the body
are completely covered.

2

1

REAR
BRACKET
PIN

4. Inspect the rear bracket.
• If the bracket comes off the roof molding or the
molding is damaged, remove the molding and go
to step 6 to install a new roof molding.
• If the bracket is OK, go to step 6.
5. Clean the roof molding and the front and rear pins
on the body using a shop towel dampened in water.
NOTE: Do not use any chemical cleaner as it may
damage the paint.

2 of 3

12-015

7. Reinstall the old roof molding or install the new roof
molding immediately after applying the Konishi
Bond.
NOTE: The Konishi Bond adhesive can skin within
seconds of exposure to air. Apply the roof molding
immediately after applying the adhesive to ensure
proper adhesion
8. Repeat steps 1 thru 8 for the other roof molding.

Example of Client Letter

May 2012
Product Update: Roof Molding Is Loose
Dear TSX Owner:
This letter is to notify you of a potential problem with your
vehicle and what you should do to resolve it.
What is the reason for this notice?
On some 2009–10 TSX vehicles, a manufacturing
problem with the roof molding may allow the molding to
come loose.
What should you do?

Call any authorized Acura dealer and make an
appointment to have your vehicle inspected. The
dealer will replace or repair the roof moldings. This
work will be done free of charge. Please plan to leave
your vehicle for a full day to allow the dealer flexibility in
scheduling.
Lessor information.

If you are the vehicle lessor receiving this product
update notice, please forward a copy to the lessee
If you have questions

If you have any questions about this notice, or need
help contacting an Acura dealer, please call Acura
Client Relations at 1-800-382-2238, and select
option 4. You can also locate a dealer online at
Acura.com.
We apologize for any inconvenience this product
update may cause you. Our goal is to ensure that your
vehicle continues to be as reliable and enjoyable as
possible.
Sincerely,
American Honda Motor Co., Inc.
Acura Automobile Division

12-015

3 of 3