xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

xxxxx-xxxxx

xxxxx-xxxxx

xxxxxxxxxxxxxxxxxxxxxx

Figure 3

23/31

NTB12-040c

8. When the screen in Figure 4 displays, reprogramming is complete.

NOTE: If the screen in Figure 4 does not display (reprogramming does not complete),
refer to the information on the next page.

9. Disconnect the battery charger from the vehicle.

10. Select Next.

Step
10

Figure 4

NOTE:
•

In the next steps (page 26), you will perform Throttle Valve Closed Position, Idle Air
Volume Learn, Accelerator Closed Position, and DTC erase.

•

These operations are required before C-III plus will provide the final reprogramming
confirmation report.

24/31

NTB12-040c

If reprogramming does not complete and the “!?” symbol displays as shown in
Figure 5:
•

Check battery voltage (12.0
– 15.5V).

•

Ignition is ON, Ready Mode
is OFF.

•

External Bluetooth® devices
are OFF.

•

All electrical loads are OFF.

•

Select Retry and follow
the on screen
instructions.
NOTE: Retry may not go
through on first attempt and
can be selected more than
once.

Figure 5

If reprogramming does not complete and the “X” symbol displays as shown in
Figure 6:
•

Check battery voltage (12.0
– 15.5V).

•

CONSULT A/C adapter is
plugged in.

•

Ignition is ON, Ready Mode
is OFF.

•

Transmission in Park.

•

All C-III plus / plus VI cables
are securely connected.

•

All C-III plus updates are
installed.

•

Select Home, and then
restart the reprogram
procedure from the
beginning.

Figure 6

25/31

NTB12-040c

11. Follow the on-screen instructions to perform the following:
•

Throttle Valve Closed Position

•

Idle Air Volume Learn (IAVL)

NOTE:
o Listed below are the conditions required for IAVL to complete.
o If IAVL does not complete within a few minutes, a condition may be out of
range.
¾
¾
¾
¾
¾
¾
¾

Engine coolant temperature: 70 -100° C (158 - 212°F)
Battery voltage: More than 12.9V (At idle)
Selector lever: P or N
Electric load switch: OFF (Air conditioner, headlamp, rear window defogger)
Steering wheel: Neutral (Straight-ahead position)
Vehicle speed: Stopped
Transmission: Warmed up (for CVT – ATF TEMP SEN less than 0.9V)

•

Accelerator Pedal Close Position Learning

•

Erase DTCs

Continue to the next page.

26/31

NTB12-040c

12. When the entire reprogramming process is complete, the screen in Figure 7 will display.
13. Verify the before and after part numbers are different.
14. Print a copy of this screen (Figure 7) and attach it to the repair order for warranty
documentation.
15. Select Confirm.

xxxxx

Step
13

xxxxx
xxxxxxx
xxxxxxxxxxxxxxxxx

Step
14

Step
15

Figure 7
16. Close C-III plus.
17. Turn the ignition OFF.
18. Disconnect the plus VI from the vehicle.
19. Test drive the vehicle and make sure it operates correctly and the MIL is OFF.
•

If the MIL comes ON, go to ASIST for further diagnostic information.

27/31

NTB12-040c

PARTS INFORMATION
This campaign applies only to 2010 Altima Sedan and Coupe (C/L32) with SULEV
(California Specification) 2.5 engine.
DESCRIPTION
Exhaust Gasket
(Front tube to center tube)

PART NUMBER

QTY

20692-65J00

1

Front Exhaust Tube W/Catalyst

20010-ZX10A

1; if needed

Exhaust Gasket
(Front tube to manifold)

20691-19U00

Nuts
(Front tube to exhaust manifold)

01223-N0021

Must be
used as
a set

Exhaust Manifold

140E2-JA92E *

Exhaust Manifold Gasket

14036-3TA0B *

Nut
(Exhaust manifold to engine head)
Bolts
(Upper heat shield to exhaust manifold)
Bolts
(Lower heat shield to exhaust manifold)

14094-JG30A
14069-JD00A
14069-ZN50A

1; if exhaust
manifold or front
tube replaced
3; if exhaust
manifold or front
tube replaced
1; if needed
1; if exhaust
manifold replaced
5; if exhaust
manifold replaced
4; if exhaust
manifold replaced
8; if exhaust
manifold replaced

* Your dealer may have exhaust manifolds and gaskets with part numbers 14002-JA91E
Manifold / 14036-JA00A Gasket in parts inventory. These exhaust manifolds and
gaskets can also be used for this repair as long as they are used together as a set.

Catalytic Converter Recycling Program
•

The Catalytic Converter Recycling Program allows Nissan to recycle the precious
metals contained within catalytic converters.

•

Refer to the latest version of the Nissan Parts and Service Bulletin NPSB/10-007 for
additional details regarding this program.

28/31

NTB12-040c

CLAIMS INFORMATION
Submit a Campaign (CM) line claim using the following claims coding:
CAMPAIGN (CM) I.D. #

DESCRIPTION
OP CODE
Reprogram ECM and leak check
PC1290
PC129
exhaust manifold & front exhaust tube,
(1)
no leak found
(1) This OP-CODE can only be used for vehicles with less than 50,000 miles.

CAMPAIGN (CM) I.D. #
PC129

DESCRIPTION
Reprogram ECM and leak check
exhaust manifold & front exhaust tube,
replace exhaust manifold.

FRT

PC1291

1.8 hrs

DESCRIPTION
OP CODE
Reprogram ECM and leak check
PC1292
PC129
exhaust manifold & front exhaust tube,
(1)
replace front exhaust tube (1)
(1) This OP-CODE can only be used for vehicles with less than 50,000 miles.

PC129

DESCRIPTION
Reprogram ECM and leak check
exhaust manifold & front exhaust tube,
replace exhaust manifold and front
exhaust tube.

1.0 hrs

FRT

PC1293

2.1 hrs

DESCRIPTION
OP CODE
Reprogram ECM and leak check
PC1294
PC129
exhaust manifold & front exhaust tube,
(1)
replace front exhaust tube gaskets.
(1) This OP-CODE can only be used for vehicles with less than 50,000 miles.

DESCRIPTION
OP CODE
Reprogram ECM and leak check
PC1295
PC129
exhaust manifold & front exhaust tube,
(1)
replace exhaust manifold gaskets.
(1) This OP-CODE can only be used for vehicles with less than 50,000 miles.

29/31

FRT

OP CODE

CAMPAIGN (CM) I.D. #

CAMPAIGN (CM) I.D. #

0.7 hrs

OP CODE

CAMPAIGN (CM) I.D. #

CAMPAIGN (CM) I.D. #

FRT

FRT
1.0 hrs

FRT
1.8 hrs

NTB12-040c

OWNER’S LETTER
For State of California owners
Dear Nissan Altima Owner:
Nissan has discovered that your model year 2010 Altima may be equipped with an
improperly calibrated Engine Control Module (ECM) that may incorrectly detect engine
valve closure as engine knock. Due to this issue you may experience some minor
drivability symptoms and a slight decrease in fuel economy under certain driving conditions.
You should also be aware that if your vehicle is not repaired it will fail a Smog Check test in
those areas of California where such testing is required under state law. The California
Department of Motor Vehicles, in conjunction with the Air Resources Board, has
implemented the Registration Renewal/Recall Tie-In Program, which requires affected
vehicles registered in California to complete the recall before the DMV will issue a
registration or renewal.
What Nissan Will Do
To correct this condition, Nissan is conducting an Emission Recall Campaign to reprogram
the Engine Control Module in your vehicle. For vehicles with greater than 50,000 miles, the
manifold catalyst will also be replaced due to possible prolonged exposure to higher than
anticipated exhaust gas temperatures. Any cracked manifold catalyst or front exhaust tube
with catalyst will be replaced regardless of vehicle mileage. This free ECM reprogramming
service should take about one hour to complete, but your Nissan dealer may require your
vehicle for a longer period of time if catalysts need to be replaced or based upon their work
schedule. To ensure the least inconvenience for you, it is important that you have an
appointment before bringing your vehicle to the dealer for service.
Your vehicle is eligible for this free service regardless of whether non-original parts were
used for previous service and repairs, or if the service was performed by a repair facility
other than a Nissan dealer.
What You Should Do
Contact your Nissan dealer at your convenience in order to arrange an appointment to
have your vehicle repaired beginning on April 16, 2012. Please bring this notice with you
when you keep your service appointment. Instructions have been sent to your Nissan
dealer.
If the retailer fails, or is unable to complete the modifications free of charge, you may
contact the National Consumer Affairs Department, Nissan North America, Inc., P.O. Box
685003, Franklin, TN 37068-5003. The toll free number is 1-800-NISSAN1 (1-800-6477261).
Thank you for your cooperation. We are indeed sorry for any inconvenience this may
cause you.

30/31

NTB12-040c

For non-California owners

Dear Nissan Altima Owner:
Nissan has discovered that your Altima may be equipped with an improperly calibrated
Engine Control Module (ECM) that may incorrectly detect engine valve closure as engine
knock. Due to this issue you may experience some minor drivability symptoms and a slight
decrease in fuel economy under certain driving conditions.

What Nissan Will Do
To correct this condition, Nissan is conducting an Emission Recall Campaign to reprogram
the Engine Control Module in your vehicle. For vehicles with greater than 50,000 miles, the
manifold catalyst will also be replaced due to possible prolonged exposure to higher than
anticipated exhaust gas temperatures. Any cracked manifold catalyst or front exhaust tube
with catalyst will be replaced regardless of vehicle mileage. This free ECM reprogramming
service should take about one hour to complete, but your Nissan dealer may require your
vehicle for a longer period of time if catalysts need to be replaced or based upon their work
schedule.

What You Should Do
Contact your Nissan dealer at your convenience in order to arrange an appointment to
have your vehicle repaired. Please bring this notice with you when you keep your service
appointment. Instructions have been sent to your Nissan dealer.
If the retailer fails, or is unable to complete the modifications free of charge, you may
contact the National Consumer Affairs Department, Nissan North America, Inc., P.O. Box
685003, Franklin, TN 37068-5003. The toll free number is 1-800-NISSAN1 (1-800-6477261).

Thank you for your cooperation. We are indeed sorry for any inconvenience this may
cause you.

31/31

NTB12-040c