SB-10043785-4798

Reference:

D at e:

NTB12-032

March 29, 2012

VOLUNTARY SERVICE CAMPAIGN
2011 TITAN AND ARMADA A/C RECEIVER / DRYER

CAMPAIGN I.D. #:

PC117

APPLIED VEHICLES: 2011 Titan (A60)
2011 Armada (TA60)
Check Service Comm to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting a Voluntary Service Campaign on certain model year 2011 Titan and
2011 Armada vehicles to replace the air conditioning system receiver/dryer and, if
necessary, the expansion valve (or expansion valves, as it applies) at no charge for parts
or labor. On some vehicles affected by this campaign, the air conditioning system may
have poor cooling performance because of improperly assembled receiver/dryer
components.

IDENTIFICATION NUMBER
Nissan has assigned identification number PC117 to this campaign. This number must
appear on all communications and documentation of any nature dealing with this campaign.

DEALER RESPONSIBILITY
Dealers are to correct each vehicle falling within the range of this campaign that enters the
service department. This includes vehicles purchased from private parties or presented by
transient (tourist) owners and vehicles in a dealer’s inventory.

1/22

REPAIR OVERVIEW

Use Service Comm (campaign ID # PC117) to confirm
the vehicle you’re working on is affected by this campaign

Replace the receiver/dryer

If debris found, replace the expansion valve(s), clean out A/C lines

Verify repairs and air conditioner operation

END

2/22

NTB12-032

SERVICE PROCEDURE
Remove Receiver/Dryer
1. Discharge (evacuate) the A/C system’s refrigerant.
•

Refer to the operator’s manual of your refrigerant recovery and charging equipment.

2. Remove the radiator as follows:
WARNING: Never remove the radiator cap when the engine is hot. Serious burns
could occur from high-pressure engine coolant escaping from the radiator.
CAUTION: Perform when the engine is cold.
a. Turn the ignition ON, and then set the temperature control lever to the highest HOT
setting or temperature position.
• Wait 10 seconds, and then turn the ignition OFF.

b. Remove the engine undercover or
skid plate.

OR

NOTE: These four (4) skid plate bolts
are T50 TORX bolts.

Figure 1

c. Remove the engine room cover (if
equipped).

Bolts

Figure 2

3/22

NTB12-032

Filler cap

d. Drain the coolant.
• Open the drain plug, and then
remove the radiator filler cap.
Drain plug

CAUTION: Do not allow the
coolant to contact the drive belt.

Figure 3

e. Disconnect the harness connector from the upper air cleaner case.
f. Disconnect the crankcase ventilation hoses at the resonator.
g. Loosen the clamp pointed out in Figure 4.
h. Remove the air duct and resonator assembly and upper air cleaner case.

Clamp

Upper air cleaner case
Resonator
Air filter

Air duct and resonator
assembly

Figure 4

4/22

Lower case

NTB12-032

i. Disconnect the in-radiator A/T fluid
cooler hoses.
NOTE: Cap or plug the opening(s) to
prevent fluid from spilling.
j.

Disconnect the radiator lower hose
from the radiator.
CAUTION: Do not allow coolant to
contact the drive belt.

k. Remove the lower radiator shroud.
• Release the three (3) lower tabs,
pull the lower radiator shroud
rearward, and then down to remove.

Figure 5

L. Disconnect the radiator upper hose
and the coolant reservoir hose from
the radiator.
CAUTION: Do not allow coolant to
contact the drive belt.
m. Unfasten the coolant reservoir and
bypass cooler hoses from the upper
radiator shroud’s clips.

Hose clips

n. Remove the upper radiator shroud:
¾ Remove the upper radiator shroud
bolts.
¾ Unclip the external A/T cooler
hose when removing the upper
radiator shroud.

Shroud tabs

Figure 6

5/22

NTB12-032

Nut

o. Remove the four (4) fan coupling
nuts, and then carefully remove the
fan coupling and cooling fan as an
assembly.
CAUTION: Do not damage or
scratch the radiator when removing
the coupling and fan assembly.
NOTE: There is no need to remove
the drive belt.
Figure 7

p. Remove the upper radiator mounting
bolts.

Bolts and
rubbers

Figure 8

6/22

NTB12-032

Brackets

Figure 9

q. Remove the A/C condenser bolts.
¾ Leave the A/C condenser brackets on at this time.
¾ Lift the A/C condenser up and then away from the radiator.
¾ The A/C condenser can be lifted by reaching in through the bumper and lower
grill (see Figure 11).
Passenger side:
Radiator bolt rubber
Condenser bolt

Figure 10

Figure 11

7/22

NTB12-032

r. Tilt the radiator toward the engine, and then remove the external A/T oil cooler bolts.
s. Lift and then move the external A/T oil cooler away from the radiator.
t. Remove the radiator.
CAUTION: Do not damage or scratch the condenser, external A/T oil cooler, or
radiator core when handling.
3. Remove the condenser as follows:
a. Disconnect the high-pressure flexible hose and the high-pressure pipe from the
condenser.
CAUTIONS:
¾ When loosening the bolts, secure the threaded flange with a suitable tool to
avoid twisting the metal piping.
¾ Cap or wrap the joint of the hose and pipe with a suitable material such as
vinyl tape to avoid the entry of air or contamination.
Threaded flange

Condenser and
bracket

Figure 12

b. Disconnect the refrigerant pressure sensor connector.
c. Move the external A/T cooler out of the way, and then remove the condenser.

8/22

NTB12-032

4. Clean off the liquid tank (receiver/dryer)
and its surrounding area.
5. Remove the receiver/dryer attachment bolt
and bracket bolt.

Bracket
bolt
Junction
pipe
Refrigerant
pressure
sensor
Attachment
bolt

Figure 13

6. Remove the receiver/dryer bracket, and
then remove the receiver/dryer by sliding
upward.
7. Inspect inside the high pressure lines and
junction pipe for debris.
•

If clean, replace the receiver/dryer with
a new one. Go to page 17.

•

If any debris is found, replace the
receiver/dryer and expansion valve(s).
Go to page 10.

CAUTION: If work is stopped for any
amount of time, cap or wrap the openings
at the condenser mounting block with a
suitable material such as vinyl tape to
avoid the entry of air or contamination.

NOTE: The junction pipe is shown as
removed in Figure 15. It does not need
to be removed.

Junction
pipe

Bracket
Receiver/
dryer

Figure 14

Condenser
mounting
block

Stud for
junction
pipe

Figure 15

9/22

NTB12-032

Replace Expansion Valve(s) (if necessary)

IMPORTANT: Follow all cautions,
warnings, and notes in the Electronic
Service Manual (ESM) when working
on or near a Supplemental Restraint
System (SRS), such as an air bag.

Remove Front Expansion Valve

1. Remove the nuts on the two (2) brackets
located on the driver side of the engine.

NOTE: The engine cover is shown
installed in Figure 16 for viewing
purposes only.

Driver side:
Remove these
nuts
Engine room
cover

Figure 16

2. Remove the bolt securing the A/C pipes,
and then move both pipes to the side.

Passenger side:
Bolt

CAUTION: Cap or wrap the openings of
the lines at the expansion valve with a
suitable material such as vinyl tape to
avoid the entry of air or contamination.

A/T filler tube

Figure 17

10/22

NTB12-032

3. For Armada only: The high pressure pipe going to the rear A/C needs to be unclipped
to move the A/C pipes.

Unclip pipe behind here
Heater pipes

Clip

Figure 18

11/22

NTB12-032

4. Remove the expansion valve’s two (2) T27 TORX bolts.

5. Pull out to remove the expansion valve.
CAUTION: Cap or wrap the openings of the lines going to the evaporator with a
suitable material such as vinyl tape to avoid the entry of air or contamination.

Expansion valve

Bolts

Figure 19

6. Titan only: Blow filtered shop air pressure through the high pressure pipe (and junction
pipe) going from receiver/dryer to expansion valve.
•
•

See page 9, step 7.
Armada only: The pipes will be blown out later on after the rear expansion valve
has been removed (see page16, step 17)

CAUTIONS:
•
•
•

Be sure to use filtered shop air pressure to avoid the entry of oil, water, or other
contamination.
Cover the end of the pipe being blown out with a clean shop rag (to catch debris).
If work is stopped for any amount of time, cap or wrap all A/C refrigerant pipe ends
with a suitable material such as vinyl tape to avoid the entry of air and
contamination.

12/22

NTB12-032

Remove Rear Expansion Valve

NOTES:
•
•

The A/C system should still be evacuated (open).
For some interior parts identification, refer to Figure 20.

4

3

1
2

9

5

8
7
6

Figure 20
1. Luggage side lower finisher RH
4. Rear lower finisher
7. Floor side finisher RH

2. Power point assembly
5. Luggage floor board
8. Tie down hooks RH

3. Cargo net hook RH
6. Storage box
9. Third row seat switches *

* If equipped.

1. Remove the cargo floor mat (not shown).
2. Remove the luggage floor board (#5).
3. Remove the rear lower finisher (#4).

13/22

NTB12-032

4. Remove the storage box (page 13, #6).
5. Remove the third row seat assembly