Bendix®-Brand Camera and Radar
Warranty Checklist
Prior to completing this checklist, follow all general
safety guidelines in this document and in the applicable
Service Data Sheet on B2Bendix.com. Refer to BW8003
on B2Bendix.com for the full Bendix Warranty Policy.

1. INITIAL ASSESSMENT

REFERENCE DOCUMENTS ON B2BENDIX.COM
BW8003

Limited Warranty – Electronic Systems

SD-29-50024

Bendix™ FLC-25™ Camera

SD-64-20124

Bendix™ FLC-20™ Camera

SD-29-50022

Bendix® FLR-25™ Radar Sensor

SD-61-4963

Bendix® FLR-21™ Radar Sensor

SD-61-4960

Bendix® FLR-20™ Radar Sensor

Is the camera or radar a Bendix product?

□
□

NO – The Bendix warranty is unavailable for non-Bendix products.
YES – Provide the following information, then continue to the Physical Inspection.
Check one:
VIN:

□

Camera

□

Radar
Bendix OEM PN:

Problem Description:

2. PHYSICAL INSPECTION
Are there signs of ANY of the following conditions (check all that apply):

□

Physical damage

□

Thermal damage

□

Corroded or damaged pins

□

Bent, cracked, or
deformed bracket

YES – If any of these conditions are present, the Bendix warranty is unavailable.

□

NO – Continue to the Bendix® ACom® Diagnostic Software Inspection.

3. ACOM DIAGNOSTIC SOFTWARE INSPECTION
Is ACom Diagnostic Software able to connect to the camera/radar?

□
□

NO – C
onfirm proper power, ground, and CAN communications at the connector per the applicable Service Data Sheet
on B2Bendix.com. Retest. If further assistance is required, contact the Bendix Tech Team. Contact information
is on the next page of this document.
YES – P
rint and submit a Diagnostic Trouble Code (DTC) Report to Bendix for further review of warranty coverage.
Instructions for submitting a warranty claim to Bendix are on the next page of this document.

GENERAL SAFETY GUIDELINES

WARNING! PLEASE READ AND
FOLLOW THESE INSTRUCTIONS
TO AVOID PERSONAL INJURY OR DEATH:

When working on or around a vehicle, the following
guidelines should be observed AT ALL TIMES:
▲Park the vehicle on a level surface, apply the parking
brakes and always block the wheels. Always wear personal
protection equipment.
▲Stop the engine and remove the ignition key when working
under or around the vehicle. When working in the engine
compartment, the engine should be shut off and the ignition
key should be removed. Where circumstances require that
the engine be in operation, EXTREME CAUTION should be
used to prevent personal injury resulting from contact with
moving, rotating, leaking, heated or electrically-charged
components.
▲Do not attempt to install, remove, disassemble or
assemble a component until you have read, and thoroughly
understand, the recommended procedures. Use only the
proper tools and observe all precautions pertaining to use
of those tools.
▲If the work is being performed on the vehicle’s air brake
system, or any auxiliary pressurized air systems, make
certain to drain the air pressure from all reservoirs before
beginning ANY work on the vehicle. If the vehicle is
equipped with a Bendix® AD-IS® air dryer system, a Bendix®
DRM™ dryer reservoir module, a Bendix ® AD-9si ®, AD-HF®,
or AD-HFi ® air dryer, be sure to drain the purge reservoir.
▲Following the vehicle manufacturer’s recommended
procedures, deactivate the electrical system in a manner
that safely removes all electrical power from the vehicle.
▲Never exceed manufacturer’s recommended pressures.
▲Never connect or disconnect a hose or line containing
pressure; it may whip and/or cause hazardous airborne
dust and dirt particles. Wear eye protection. Slowly open
connections with care, and verify that no pressure is
present. Never remove a component or plug unless you are
certain all system pressure has been depleted.
▲Use only genuine Bendix ® brand replacement parts,
components and kits. Replacement hardware, tubing, hose,
fittings, wiring, etc. must be of equivalent size, type and
strength as original equipment and be designed specifically
for such applications and systems.
▲Components with stripped threads or damaged parts should
be replaced rather than repaired. Do not attempt repairs
requiring machining or welding unless specifically stated
and approved by the vehicle and component manufacturer.
▲Prior to returning the vehicle to service, make certain all
components and systems are restored to their proper
operating condition.
▲For vehicles with Automatic Traction Control (ATC), the ATC
function must be disabled (ATC indicator lamp should be
ON) prior to performing any vehicle maintenance where
one or more wheels on a drive axle are lifted off the ground
and moving.
▲The power MUST be temporarily disconnected from the
radar sensor whenever any tests USING A DYNAMOMETER
are conducted on a vehicle equipped with a Bendix ®
Wingman ® system.
▲You should consult the vehicle manufacturer's operating
and service manuals, and any related literature, in
conjunction with the Guidelines above.

SUBMITTING A WARRANTY CLAIM TO
BENDIX
• Bendix recommends contacting the Tech Team prior to
submitting a warranty claim. If applicable, include the Ticket
Request Number: ______________________________
• Replace the camera/radar with a new, corresponding
Bendix service kit.
• C lear DTCs and generate a DTC report with ACom
Diagnostic Software.
• Include the following documentation when submitting a
warranty claim:
»

Completed Bendix claim form

»

TC report from the ACom Diagnostic Software
D
section of this document (including the DTCs that
were unable to be cleared)

»

TC report following the installation of the
D
replacement camera/radar (showing that all DTCs
were successfully cleared)

»

This completed checklist

TECHNICAL SUPPORT
For technical support, contact the Bendix Tech Team at
1-800-AIR-BRAKE (1-800-247-2725), Monday through
Thursday, 8:00 a.m. to 6:00 p.m., and Friday, 8:00 a.m. to
5:00 p.m. ET. The Bendix Tech Team can also be reached
by email at techteam@bendix.com.

Unless otherwise indicated, the trademarks used in this document, including Bendix,
are United States trademarks owned by, or licensed to, Bendix Commercial Vehicle Systems LLC.

BW8286 Rev 000 © 6/2026 Bendix Commercial Vehicle Systems LLC, a member of Knorr-Bremse • All Rights Reserved