Service

Technical Information

2025

ENU

ASA3

9

ASA3 – Re-Program Reversing Camera Control Unit and, if necessary, Replace Reversing Camera and
Surround View Cameras (Recall Campaign)
Important:

CRITICAL WARNING -This campaign includes steps where control unit(s) in the vehicle will be programmed
with the PIWIS Tester. The vehicle voltage must be maintained between 13.5 volts and 14.5 volts during this
programming. Failure to maintain this voltage could result in damaged control unit(s). Damage caused by
inadequate voltage during programming is not a warrantable defect. The technician must verify the actual
vehicle voltage in the PIWIS Tester before starting the campaign and also document the actual voltage on the
repair order.

Model Year:

As of 2024 up to 2026

Change
Overview:

Version

Date

Change

0

04/25/2025

•

First publication

1

01/13/2026

•
•

Update of Warranty processing
Update of labor time for scope 1 and 2

2

04/20/2026

•

Update of WSD0, changed to WSJ0

Model Line:

Macan Electric (XAB)

Equipment:

Front and rear ParkAssist assistance systems incl. reversing camera (M-no. KA2)
or
ParkAssist assistance systems incl. Surround View (M-No. KA4)

Concerns:

Reversing camera control unit
Surround view camera

Cause:

In rare cases, the reversing camera of the affected vehicles cannot be activated when ParkAssist is
switched on due to a software error. In addition, with a very small number of affected vehicles, it is
possible that the housing of the reversing camera and individual surround view cameras in the surround
view equipment option were not bonded as per default value specifications.
As a result, no camera image is displayed in the central display when ParkAssist is activated contrary to the
default value specifications. If the camera housing is not bonded correctly, moisture can penetrate and impair
the camera image.

Action:

Re-program reversing camera control unit using the PIWIS Tester and replace reversing camera and individual surround view cameras if necessary.

AfterSales

Apr 20, 2026
Page 1 of 14

9

Service
ASA3

ENU

Technical Information

2025

Information
Each vehicle was assigned exactly to one scope that includes the actions required for each vehicle.
The relevant scope assigned to the vehicle for this campaign can be seen in the PCSS Vehicle Information.

Information
The minimum programming requirement is the PIWIS Tester software release 43.300.040 (or higher).
Affected
vehicles:

Only vehicles assigned to the campaign (see also PCSS Vehicle Information).

Required Parts as and when necessary
Information
Each vehicle was assigned exactly to one scope that includes the actions required for each vehicle.
The relevant scope assigned to the vehicle for this campaign can be seen in the PCSS Vehicle Information.
The part numbers of the required parts for the respective vehicle can be viewed in the assigned scope. For
an overview of the campaign scopes, see "Warranty processing".

Required tools
Tools:

•
•

P90999 - PIWIS Tester 4
Battery charger with a current rating of at least 90 A and a current- and voltage-controlled charge map
for lithium starter batteries, e.g. VAS 5908 battery charger 90 A. For further information about the
battery chargers to be used, see the corresponding Workshop Manual. ⇒ Workshop Manual '270689
Charging vehicle electrical system battery'

Additionally required tool to replace the reversing camera:
•
•
•

Torque wrench, 2-10 Nm (1.5-7.5 ftlb.), e.g., V.A.G 1783 - torque wrench, 2-10 Nm (1.5-7.5 ftlb.)
VAS 6350A - Calibration unit
VAS 6350/2A - Distance laser

Additionally required tool to replace the front surround view camera (front camera):
•
•
•

Torque wrench, 0.4 - 2 Nm (0.3-1.5 ftlb.), e.g.VAS 6253A - torque wrench, 0.4 - 2 Nm (0.3-1.5 ftlb.)
Torque wrench, 40-200 Nm (30-148 ftlb.), e.g., V.A.G 1332A - Torque wrench, 40-200 Nm (30-148
ftlb.)
VAS 6266A - Wheel fitting trolley

Additionally required tool to replace the left or right surround view camera:
•
Apr 20, 2026
Page 2 of 14

Torque wrench, 0.4 - 2 Nm (0.3-1.5 ftlb.), e.g.VAS 6253A - torque wrench, 0.4 - 2 Nm (0.3-1.5 ftlb.)

AfterSales

Service

Technical Information

2025

ENU

ASA3

9

Overview of actions
Information
Every vehicle is assigned to exactly one campaign scope.
⇒ To determine the scope assigned to the relevant vehicle, see PCSS Vehicle Information.
The action to be carried out for the respective scope can be read in the following table.
Scope 1 and 2 only include the required programming of the reversing camera control unit.
Vehicles that are assigned to scope 2 are also assigned to the workshop campaign WSJ0 - extension to
software network VR28.13 - and have not yet received this software update.
On these vehicles, the reversing camera control unit is programmed as part of the software update WSJ0.
For this purpose, please carry out the workshop campaign WSJ0 without fail.
Action
Scope 1

Re-program reversing camera control unit.
⇒ Technical Information '270689 Re-program reversing camera control unit'

Scope 2

Re-program reversing camera control unit as part of the WSJ0 campaign implementation.
⇒ Technical Information '270689 WSJ0 – Update to Software Network VR28.13 (Workshop
Campaign)'

Scope 3
- 10

Re-program reversing camera and replace various cameras.

⇒ Technical Information '270689 Replace reversing camera and, if necessary, various
surround view cameras'

Replace reversing camera and, if necessary, various surround view cameras
Work Procedure: 1

Replace the reversing camera and, if necessary, various surround view cameras according to the
assigned scope of the vehicle.
Replacement of the following cameras:
Reversing camera
control unit

Front surround
view camera
(Front camera)

Left surround view
camera

Right surround
view camera

Scope 3

Yes

No

No

No

Scope 4

Yes

Yes

No

No

Scope 5

Yes

No

Yes

No

Scope 6

Yes

No

No

Yes

Scope 7

Yes

Yes

Yes

No

Scope 8

Yes

Yes

No

Yes

Scope 9

Yes

No

Yes

Yes

Scope 10

Yes

Yes

Yes

Yes

AfterSales

Apr 20, 2026
Page 3 of 14

9

Service
ASA3

ENU

Technical Information

2025

Replace reversing camera.
For work procedure, see: ⇒ Workshop Manual '914319 Remove and install reversing camera control
unit (J772)'
Replace front surround view camera (front camera).
For work procedure, see: ⇒ Workshop Manual '916919 Remove and install front camera'
Replace left/right surround view camera or both.
For work procedure, see: ⇒ Workshop Manual '916719 Remove and install side camera (R244)'
2

Continue with ⇒ Technical Information '916719 Re-programming reversing camera control unit'.

Re-program reversing camera control unit
NOTICE
Sitting inside the vehicle during the update
•

Update cancelled by automatic ignition activation

Þ
⇒

Avoid sitting inside the vehicle during the update.
NOTICE

The specified update process was not followed
•

Update cancellation

•

Destruction of control units

Þ
⇒

Observe and follow the process displayed for the update and instructions for the PIWIS Tester

Þ
⇒

Do not replace ignition without instructions from PIWIS Tester

Þ
⇒

Repeat the programming only if a failed update is displayed on the PIWIS Tester

Apr 20, 2026
Page 4 of 14

AfterSales

Service

Technical Information

2025

ENU

ASA3

9

Information
Vehicle update – general information
The entire vehicle network will be checked for a necessary update or computed to ensure fault-free functioning of the vehicle. For this purpose, the following preparations are to be made:
•

Latest release on PIWIS Tester 4 and PiUS available

•

Vehicle is fully built up

•

VCI and PIWIS Tester 4 must be connected to each other via workshop Wi-Fi

•

The user must be logged in to the PIWIS Tester 4 in the PPN

•

Vehicle must be supported with an external charger

•

Seat heating and seat ventilation are not active

•

Place the original hand-held transmitter in the emergency start tray (see Workshop Manual)

The vehicle performs the update independently. The current status can be retrieved on the diagnostic tester
or on the front display and control panel (R238) under Messages (RPC+).

Information
The entire update process for this action takes approx. 5 minutes.
However, the download speed of the update package depends on the performance of the local network and
can vary accordingly.
Work Procedure: 1

Observe preconditions for control unit programming.

⇒ Technical Information '9X10IN Basic instructions and procedure for control unit programming using
the PIWIS Tester'

Information
An active Internet connection with the PIWIS Tester must be ensured.
The technician must log in to PPN with the PIWIS tester.
The PIWIS Tester must not be charged using the cigarette lighter!

Information
Before starting the diagnosis, it is essential for an ignition change to be performed on the vehicle.
Subsequently, after starting the diagnosis, the VCI is automatically initialized and the control unit data is
loaded.
For additional information on the programming procedure and if the process is aborted, see ⇒ Technical
Information '9X10IN FAQs on control unit programming and coding'.
2

Prepare the programming of the reversing camera control unit (J772).

AfterSales

Apr 20, 2026
Page 5 of 14

9

Service
ASA3

ENU

Technical Information

2025

2.1

Start new logging via •P2“.

2.2

As soon as the control unit overview is displayed, open the additional menu •F7“.
An overview of all campaigns to be carried out for the respective vehicle is then displayed automatically.

3

2.3

Confirm the campaigns to be carried out for the respective vehicle by pressing •F12“, but do
not start for the time being.

2.4

Create Vehicle Analysis Log. Flag the created VAL with "before repair".

2.5

During the automatic integration test on the PIWIS Tester, press •F11“ to cancel it.

Re-program the reversing camera control unit (J772).
In the displayed additional menu, select and confirm the "Control unit programming and coding
(campaign)" menu item.
The required software update for the reversing camera control unit is then displayed.
Start the software update with •F8“ and program as per the menu.
After updating is complete, a corresponding confirmation is displayed on the PIWIS Tester.
Information
During the update process, all displays in the vehicle (instrument cluster, central display and passenger
display) are occasionally switched off. Programming nevertheless continues. The ignition sequence
must not be changed.
If Wi-Fi coverage is insufficient, the connection
between the PIWIS Tester and VCI can be interrupted
(battery charge indicator inactive on the Tester
display at the top right). The vehicle will, nevertheless,
continue programming independently. In the
meantime, no entry may be made on the PIWIS Tester,
and the programming must not be restarted. In such
a case, the progress of the update can still be followed
inside the vehicle via the central display by activating
the ''Messages'' tile.

For specific information on control unit programming
during this campaign, see the table below.

Update progress on central display

Required PIWIS Tester software release:

43.300.040 (or higher)

Type of control unit programming:

Control unit programming via the "Programming and
coding control units (campaign)" function.

Campaign to be carried out: ASA3

Apr 20, 2026
Page 6 of 14

AfterSales

Service

Technical Information

2025

Programming sequence:

ENU

ASA3

9

Read and follow the information and instructions on
the PIWIS Tester during the guided programming
sequence.
Do not interrupt the programming and coding
process.
A backup documentation process for the
re-programmed software releases starts after
programming and coding.

Programming time (up to):

5 minutes

Procedure if error messages appear during
programming sequence:

⇒ Technical Information '9X10IN Basic instructions

Procedure in the event of a termination in the
control unit programming:

Continue the campaign sequence to the end, then
carry out the integration test again when the test is
complete and restart programming by entering the
programming code.

and procedure for control unit programming using
the PIWIS Tester'

Specific information on how to proceed if aborted: ⇒
Technical Information '9X10IN FAQs on control unit
programming and coding'
4

5

After programming is completed, perform a vehicle bus idle.
4.1

Go back to the control unit overview by pressing •F11“.