BULLETIN NOTES
This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red.
Previous TSBs:

Date(s) Issued:

Previous TSBs: Date(s) Issued: Previous TSBs: Date(s) Issued:

SA-007/25

10/22/25, 06/02/25 and 02/03/25

01-002/19

01/02/19

01-013/10

02/15/10

SA-032/24

05/21/24

01-009/18

03/26/18

01-032/07

08/01/07

01-007/23

11/07/23 and 05/09/23

01-005/16

05/23/12

01-025/04

07/21/04

01-003/22

03/17/22

01-018/12

05/23/12

01-005/21

02/08/21

01-054/10

12/13/10

APPLICABLE MODEL(S)/VINS
2020-2026 Mazda3

2020-2026 CX-5

2023-2026 CX-50 (All)

2020-2021 Mazda6

2020-2023 CX-9

2024-2026 CX-90 (All)

2020-2021 CX-3

2020-2026 CX-30

2025-2026 CX-70 (All)

2020-2026 MX-5

2022-2023 MX-30

NOTE: For 2026 CX-5, the DCA-8000 will not read the VIN. Manually enter a 2025 CX-5 for testing purposes. This
will be updated in a future software release.
DESCRIPTION
The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery
testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test
Mazda vehicle batteries and to generate a Warranty Code.
NOTE: A Warranty Code is required for warranty claim submission
Battery Identification (Mazda batteries have 2 rating types)
1. JIS (Japanese Industrial Standard):
JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the
battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in
Japan come from the factory with a JIS rated battery.
NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery.

Page 1 of 7

04/22/2026 09:33 AM tlawrenc

2. CCA (Cold Cranking Amps):
CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps.
CCA rated batteries are supplied with domestically produced vehicles.
NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty
Code from the tester. This will also result in unnecessary replacement of batteries.
TEST PROCEDURE
1. Connect the charger clamps to the appropriate battery posts.
NOTE: For CX-90/CX-70 Clamp Attachment, use duct tape (A) or equivalent to hold the cable as shown.

2. At the Main Menu, select In Vehicle Charge and the Acquire VIN screen is displayed.

Page 2 of 7

04/22/2026 09:33 AM tlawrenc

3. Scan the barcode located on the driver’s side door frame using the provided wireless barcode scanner. A single beep
indicates the scan was successful.
NOTE: For 2026 CX-5, the DCA-8000 will not read the VIN. Manually enter a 2025 CX-5 for testing purposes. This
will be updated in a future software release.
NOTE:
• If the DCA-8000 isn't used very often, the scanner might go dead because it only charges when the unit is
plugged in and on.
• If your barcode scanner is unavailable for some reason, the VIN can also be entered manually.
• If the battery parameters were not filled in from the VIN scan, manually enter the battery information.
• Select the correct rating system for the battery by identifying the correct JIS code (A) stamped onto the battery top
or CCA code (B) printed on the battery label. The battery hold down may need to be removed in order to read the
JIS code.
• Look at the actual battery in the vehicle and enter the JIS/CCA code.

• For CX-90/CX-70 H3T (inline 6) M Hybrid Boost, use the following information for DCA-8000 test/charging since
the battery label is not visible without removing the battery.
JIS (Japanese Industrial Standard) - 75D23L
CCA (Cold Cranking Amps) - 465A
• For CX-90/CX-70 PHEV (2.5L), the battery label is not visible, but the battery type is Q85. Use the following
temporary Q85 Battery Charging Procedure until DCA-8000 software update is available.
○
○

a. Change Cranking Units to CCA.
b. Edit Battery Info, then Select Continue.
•
•
•
•
•
•

Battery Type - I-ELOOP
Cranking Units - CCA
Cranking Rating - 520 (Q85 type battery) or 622 (S95 and LN3 type battery)
Post Location - Top Post
Capacity Units - Rated Ah
Capacity Rating - 65 (Q85 type battery) or 72 (S95 and LN3 type battery)

4. Complete the battery test by following the on-screen instructions and entering the appropriate information. Refer to the
Mazda DCA-8000 Quick Start Guide or Midtronics online Instruction Manual for more information.

Page 3 of 7

04/22/2026 09:33 AM tlawrenc

5. After the test, the DCA-8000 will display one of the possible battery test results listed below. Review the results and
follow the Action for the displayed result.
Battery Tester Display
“GOOD BATTERY”

Action
Return the battery to service.

“GOOD - RECHARGE”

Fully charge the battery and return it to service.

“CHARGE AND RETEST”

Fully charge the battery and retest. Failure to fully charge th
e battery before retesting may cause false readings. If CHA
RGE AND RETEST appears again after you fully charge th
e battery, replace the battery.

“REPLACE BATTERY”

A REPLACE BATTERY result may also mean a poor conne
ction between the battery and the vehicle. If you tested the
battery using the System test, disconnect the battery cables
and retest using the Battery Test before replacing it.

6. Select Send Results then select Print to get a test result print out.

Page 4 of 7

04/22/2026 09:33 AM tlawrenc

TEST PROCEDURE FOR VEHICLES EQUIPPED WITH I-STOP

NOTE: Check the specifications before entering information because the i-stop vehicle markings vary depending on the
vehicle model.
1. Connect the charger clamps to the appropriate battery posts.
2. At the main menu, select In Vehicle Charge and the Aquire VIN screen is displayed.
3. Scan the barcode located on the driver’s side door frame using the provided wireless barcode scanner.
NOTE: A single beep indicates the scan was successful.
4. After VIN is scanned, clicked "enter VIN manually" or "manual entry". Then enter the battery information manually.
NOTE: This will autocmatically transfer the 17-digit VIN.
5. For I-STOP batteries, enter the battery type as i-ELOOP.

Page 5 of 7

04/22/2026 09:33 AM tlawrenc

NOTE: Select the correct rating system for the battery by identifying the correct JIS code (A) stamped onto the battery
top or CCA code (B).

6. Run battery test by following the on-screen instructions, visit the Midtronics online Instruction Manual for more
information.
7. Select Send Results then select Print to get a test result print out. Write the Warranty Code on the RO and attach the
printed results to the RO (do not attach with tape due to reaction with the printer paper).
NOTE: A Warranty Code is required for warranty claim submission. Claims filed WITHOUT correct codes will be subject
to warranty claim denial.
REPAIR PROCEDURE
1. Perform appropriate repair to vehicle. If needed, use the Battery Diagnostics of the DCA-8000 to test the charging and
starting systems by following the on-screen instructions for entering the appropriate information. Refer to the Mazda
DCA-8000 Instruction Manual for more information.
2. Verify the repair.

Page 6 of 7

04/22/2026 09:33 AM tlawrenc

WARRANTY INFORMATION
1. Write the Warranty Code on the RO and attach the printed results to the RO (do not attach with tape due
to reaction with the printer paper).
NOTE: A Warranty Code is required for warranty claim submission. Claims filed WITHOUT correct codes
will be subject to warranty claim denial.

Page 7 of 7

04/22/2026 09:33 AM tlawrenc