+ Note: The vehicle uses acoustic signals and flashing lights to indicate when user input is required during and at the end of the test
program.
+ Important: Please prepare the required USB-C sticks (see parts information) before starting the repair. The update media can be used
for multiple vehicles.
+ This update package also includes new software for the MIB3 infotainment system. Useful information for MIB3 software updates can be
found in TSB 2060523, 91 M/B3: Software Update Instructions.
Repair procedure
1. Software update for emergency call module (0075), gateway (0019) and information electronics (005F)
Determine the software version in diagnostic address 0019 with SVM code DUCIDENT0019
(SVM — Authorized Multiple Code Entry)
See
ne
=F
ates
You must then use the appropriate SVM code chain for the determined software version in the function “SVM — Authorized Multiple Code
Entry”.
Software version in diagnostic address 0019 = 0042
DUCDTCPR0075MLB,FLIGHTON0075MLB,ZGDOIP,CL3BPA001US, 19A027,19B027,TGU1MDMVB,CL3BPA002US,FLIGHTOFF0075MLB
f=) + am Me [=]
=
eo 4 Loe
Al E; | ms
Lo x
IZ J + SE 43
OS ee :
= = 4 ris + a. 4
ix. "= 7
Opa oO Se oO
Me oe ei
", Ld fs
wrap Syste: ol
—-=
A Be mat Nay
oo W 1 _
lo aap “out O17,
a ieee
Only software version 0042 in diagnostic address 0019
All other versions in diagnostic address 0019
DUCDTCPRO0075MLB,FLIGHTON0075MLB,ZGDOIP,CL3BPA001US, TGU1MDMVB,CL3BPA002US, FLIGHTOFF0075MLB

io goede * [a]
. ‘
Lat I
* _ in OM} Ab
erait “13
eae] he a
7 = same on
er Dee
om A cat = hy =
fo= a Er OF.
- L. | * ike
om ha 1
ae ers tt
— aL, uh PT
a om te oe
Toe koe
Oo} ee i oy =
7 =
The test program initially prompts you to use a USB medium (see parts information for part number).
The automatic execution of software updates results in inactive time. This is considered in the warranty accounting instructions.
The USB-C stick can be removed after completing the program.
Note: If the procedure has been interrupted, please repeat step 1. The test program will then automatically perform the missing part of the
update.
2. Bus sleep mode
Put the vehicle in bus sleep mode after performing the software update.
Then switch the ignition back on and start the MMI.
3. Check emergency cal] LED
Check whether the emergency call LED in the roof module lights up in green again
If the LED does not turn green, please refer to TSB 2079652 Emergency call LED in roof module not lit up in green.
4. End diagnostic session and send off diagnostic log online.
Warranty
Claim Type: + Ifthe vehicle is outside of any warranty, this Technical Service Bulletin is informational only.
Service Number: Complaints about online services or the emergency call function:
Service number: 9145
Complaints about MMI functions:
Service number: 9196
Damage Code: 0041
Labor Operations: Prepare repair 0151 0010 20TU
- Vehicle parked
- Charge 12 V battery
Launch software update for MMI and emergency call module 0151 0040 60 TU
- Connect tester, start ODIS
- Flash mode
- Function Authorized Multiple Code Entry
- Copy/paste the code chain ==> Start
- Insert the USB stick.

- Program runs automatically (service technician is not required) ee |

Claim Comment: As per TSB 2079979/3
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject
to review or audit by Audi Warranty.
When carrying out this TSB, time stamps are not required for billing under warranty.
You are therefore permitted to work on other vehicles at the same time. The update can also be performed by non-productive personnel
The Guided Fault Finding test plans should not be carried out for diagnostic entries that are repaired by performing this TSB and cannot be
invoiced.
Required Parts and Tools
The following applies when creating the update media:
Please prepare the required USB-C sticks before starting the repair.
You must not use an SD card with an adapter USB stick.
The USB-C stick and downloading the software via the SD creator cannot be invoiced.
General information on USB-C sticks for software updates can also be found in TSB 2060523, 91 MIB3: Software Update Instructions.
MIB3 update media:
Download the software with the corresponding part number onto a USB-C stick (min. USB 2.0 with 32 GB).
Please do not use a USB-C stick with a larger storage capacity as such USB sticks have a different formatting process.
e-tron GT 4014 8W0906961GB.

4026

4404
4318 8W0906961GF
Additional Information
All part and service references provided in this TSB (2079979) are subject to change and/or removal. Always check with your Parts Department
and/or ETKA for the latest information and parts bulletins. Please check the Repair Manual for fasteners, bolts, nuts, and screws that require
replacement during the repair.
©2026 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest information available at the
time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies, and its
licensors. Alll rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be
modified or reposted to other sites, without the prior expressed written permission of the publisher.