A Connection offline
Technical Service Bulletin Transaction No.: 2079692/5
00 Aid for TSB 2079690 (00 Combined software update 03.10.00/C (28.13.01) KD2)) Release date: Mar 20, 2026
Condition
Model(s) VIN Range Vehicle Specific Equipment
AS, $5 (FU), A6 Sportback e-
tron, S6 Sportback e-tron, Q5, O0A5 Software:
Q5 Sportback, SQ5, SQ5
Sportback (GU), Q6 e-tron, Q6 2025 All 0250
Sportback e-tron, SQ6 e-tron, 0295
and SQ6 Sportback e-tron

REVISION HISTORY
revision [onto [pupoe

5 Revised header (Added software)

Revised Condition (Updated model table)

02/06/2026 | Revised Service (Updated configuration of information, verbiage)
01/22/2026 | Revised Service (Updated verbiage)
Aid document if flashing is aborted for TSB 2079690, 00 Combined software update 03.10.00/C (28.13.01) KD2.
Technical Background
Not applicable.
Production Solution
Not applicable.
Service
General information:
If a vehicle has already been updated partially using a code and an error occurred during the update, do not attempt
to repair the vehicle via "SVM - Check vehicle configuration".
Please make absolutely sure to observe the information displayed on the tester before sending a support request.
0x0009 Control module in | Programming conditions Erase event memory and

after-run not met perform update again

ignition off and on again
or wait for a bus sleep
cycle):
DA -— control unit name
8060 or 8096 Possible causes: lost Perform bus sleep cycle (at
configuration after a least 15 minutes) and then
software update or control | repeat procedure using
units which can no longer | SVM code.
be reached due to a
software update.
9024 or ODS1008E When the GSB bus times __| Perform update again. If
Connection out, the ODIS-S tester this is unsuccessful, please
makes four attempts to contact the ICT
Negative response from __| establish the connection. administrator.
server
Vibration of the steering Refer to TSB 2076547, 48
wheel during the flashing General information on
procedure is a normal flashing procedure
occurrence. If the steering | (vibrating steering wheel).
wheel still vibrates after the
update has been
completed.
File transmission freezes | The data required for the Please check the EdgeBox
for longer than 5 software update cannot be | and firewall settings with
minutes. ODIS tester downloaded from the the help of your IT
displays message about | workshop server administrator and configure
this for longer than 5 (EdgeBox). the firewall in accordance
minutes. a with the ODIS release
This is generally caused by | jotes.
a firewall setting on the
workshop tester. If this In particular, it is necessary
error occurs for the first to enable port 8080.
time, please check the
firewall settings (refer to
campaign description) and
enter the code again.
8060, 8118, 8125, 8090, Flashing aborted at Please note the information
SDB20FOE (control diagnostic address 006C; |in TSB 2080613, 00
module cannot be diagnostic address 8117 Workshop info:
reached) (diagnostic can no longer be reached. | irregularities when
addresses 8117 and performing KD2 combined
006C) software update on
diagnostic address
8117+006C - PPE/PPC.
8060 or 8118 (possible Multiple electric exterior Please note the information
diagnostic address: door handles can no longer | in TSB 2080648, 57 One or
4200, 4201, 4202, 4203) be reached after flashing is | more electric exterior door
aborted. handles cannot be reached
during KD2 update.
“A further attempt can be started subsequently in order to try to update the vehicle to the new version. Please
perform the procedure again until the software update is successful...”

This dialogue can be confirmed by selecting “Yes” if the SVM code has already been used and therefore if
modifications to the vehicle have already been made.

If the SVM code is being used for the first time on this vehicle, please refer to the information on the ODIS tester.
Warranty

This TSB is informational only and not applicable to any Audi Warranty.

Additional Information

All part and service references provided in this TSB (2079692) are subject to change and/or removal. Always check
with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair
Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.

©2026 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time
without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form
or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be
modified or reposted to other sites, without the prior expressed written permission of the publisher.