A Connection offline
Technical Service Bulletin Transaction No.: 2076994/7
27 Valeo 48V starter generator (BSG) DTC POA1A00 P19F800 POA1E00 U014600 .
U300100 P10F300 P056200 P056100 P065200 PO69800 Release date: Mar 20, 2026
Condition
Model(s) VIN Range Vehicle Specific Equipment
A8, and Q8 2024 — 2026
A6 and A7 2024 - 2025 All PR Code 8GK — MHEV with 48V Belt Starter
Generator
A6 allroad, and
REVISION HISTORY
revision [pate [purpose
7 Revised Production Solution (Updated verbiage)
Revised Service (Updated verbiage, software versions revised)
01/05/2026 Revised header (Corrected models)
Revised Condition (Added model table)
Revised Service (DTCs and scenario added)
Revised Warranty (Scenario claiming added)
5 10/24/2025 Revised header (Added MY26 and software versions)
Revised Condition (added customer concerns and workshop findings)
Revised Service (Updated verbiage and ETA for further software arrival)
Revised Warranty (Updated warranty table)
Customer states:
+ The engine warning lamp (MIL) is on (Figure 1).
260m, >) @Danger (featensniflaiul
ee +4
/ =40

Figure 1. MIL is illuminated.
Workshop findings:
The following DTCs are stored paired in their respective modules during a workshop visit (service/inspection) or
while the customer used the car:

Engine Electronics, J623 (address word 0001):

+ U046900: Alternator control module, implausible signal

+ Other DTCs — See below

In the starter-generator control unit (address word 0OCC) or in the functional check C29:

+ Other passive entries - See below

Technical Background
The software for the Starter Generator, C29 (address word 00CC) needs to be updated.

Production Solution

New software implemented in production week 07/2025 // 12/2026.

Service
This TSB closes PSS 2076029, 27 PSS Valeo 48V Starter Generator (BSG) DTCs POA1A00 + P19F800.
Please check which of the three scenarios apply to the vehicle:
Scenario 1)

+ Starter Generator (address word 00CC), or functional check C29 contains NO POE0*00 / P2DC* DTCs
Check whether any of the listed DTCs are logged in the Starter Generator, C29 (address word 00CC) in your
specific case. If they are, this TSB applies. The software for the Starter Generator, C29 (address word OOCC) must
be updated (software part number 4M0.903.028). It is not permitted to replace parts in this case.

U014600 38877 Software Solution 0610 - SVM Code CCA005

U300100 41556 Software Solution 0610 - SVM Code CCA005

P10F300 41572 Software Solution 0610 - SVM Code CCA005

P056100 41825 Software Solution 0610 - SVM Code CCA005

P19F800 38806 Software Solution 0610 - SVM Code CCA005

POA1E00 38862 Software Solution 0610 - SVM Code CCA005

POA1A00 45888 Software Solution 0610 — SVM Code CCA005

P069800 414833, 41832 Software Solution 0610 — SVM Code CCA005

P056200 Software Solution 0610 - SVM Code CCA005
P065200 41831, 41826 Software Solution 0610 - SVM Code CCA005
If necessary, from the DTCs above:
1. Follow all instructions in TSB 2011732: 00 Software Version Management (SVM), operating instructions.
2. Update the Starter Generator, C29 (address word OOCC) using the SVM action code as listed in the table
below, if necessary:
Old Software Part Hardware Part Old Software New Software SVM Code Input
Number Number Version Version
(or higher)
4M0.903.028 4M0.903.028 0606 or 0608 0610 CCA005
The software for the starter-alternator control unit must be updated on this vehicle. Please observe the
information and instructions under “Additional Information” regarding this.
Scenario 2)
+ Starter Generator, C29 (address word 00CC) contains POE0*00 / P2DC* DTCs
There is a hardware issue and the Starter Generator, C29 (address word OOCC) may be replaced. Do not perform a
software update as this could lead to repeat complaints.
Scenario 3)
* Scenario 2 does not apply and diagnostic address 00CC or functional check C29 contain static
P0A1E00 entries
In this scenario, erase the DTC memory and wait for the system to complete a bus sleep cycle. Reassess the DTC
entries.
If the POA1E00 DTC entry remains static, there is a hardware issue and the belt-driven starter-alternator may be
replaced.
Do not perform a software update as this could lead to repeat complaints.
Warranty
Unjustified work/replacement parts will be charged back. Invoicing under warranty is not permitted.
Claim Type: + If the vehicle is outside of any warranty, this Technical Service Bulletin is
informational only.
Damage Code: Scenario 1: 0039

Scenario 2: 0040
Scenario 3: 0040
Labor Operations: | Scenario 1: Only if 48V starter/generator is NOT replaced
Software Update 0151 0010 Time stated on the
diagnostic protocol
Software Update 0151 0060 Time stated on the
diagnostic protocol
Please note the information on predecessors and items that are included and excluded in
the repair operations, as well as any associated tasks.
Scenario 2 & 3: Only if 48V starter/generator IS replaced
Remove and install 48V starter/generator 2726 1944 See SRT with
associated
operations
GFF/Guided Functions 0150 0060 Time stated on the
diagnostic protocol
Scenario 3 ONLY: Only if 48V starter/generator IS replaced
Check vehicle (bus sleep cycle) 0689 0199 10 TU
Please note the information on predecessors and items that are included and excluded in
the repair operations, as well as any associated tasks.
Claim Comment: As per TSB 2076994/7
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures
Manual. Claims are subject to review or audit by Audi Warranty.
Additional Information
The software must be updated on a control unit in this vehicle, or the software must be updated on several control
units in this vehicle to ensure they function correctly in conjunction with the other control units in the vehicle. Please
inform the customer about the software update in question and ask whether they or other third parties have modified
the software (e.g. tuning or retrofitting involving modifications to the vehicle’s software). Please refer the customer to
the Warranty and Maintenance booklet to learn more about how chip tuning can impact warranty coverage. Please
inform the customer that this software update may neutralize previous modifications to the vehicle’s software
performed either by the customer or other third parties.
If the customer declines the software update, please inform them that this could lead to issues or restrictions with
the use of the vehicle or individual components.
Make a note to this effect on the order before it is signed by the customer. Include this information in the customer
file.
All part and service references provided in this TSB (2076994) are subject to change and/or removal. Always check
with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair
Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.
©2026 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time
without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form