9

Install front camera (dashcam) on the windshield
NOTICE

Adhesive films not prepared/installed correctly
•

Damage to adhesive films

•

Inadequate adhesion of adhesive films

Þ
⇒

Carefully clean the areas on which you intend to stick the film to ensure that all traces of oil,
grease and silicone are completely removed.

Þ
⇒

Do not touch the bonding surfaces.

Þ
⇒

Object (adhesive film, vehicle, etc.) and ambient temperature: Minimum temperature 15°C / 59
°F.
2.2.1

Pull 3M privacy film off the backing
Þ Figure 6 -A-).
sheet (⇒
1
2
3

– 3M privacy film
– Marked bonding surface
– Interior mirror base

2.2.2

Position 3M privacy film on the
marked bonding surface on the
Þ Figure 6 -B-).
windshield (⇒

2.2.3

Carefully affix 3M privacy film using
a plastic squeegee, starting from the
center and moving towards the edge.

Figure 6

Tequipment

Mar 24, 2026
Page 7 of 20

9

911 (992)
9163

Installation and Conversion Instructions

ENU 18/22

2.2.4

Pull protective film off the front
Þ Figure 6
camera retainer plate (⇒
-A-).
1
2
3
4

– Protective film
– Front camera
– 3M privacy film
– Interior mirror

Information
Observe the following points during
positioning/alignment:
•

Sufficient distance between
front camera and interior mirror
base: at least 5 mm/ 0.2 in.

•

Get another person standing in
front of the vehicle to check
and confirm the horizontal
alignment of the camera with
the PORSCHE logo!

Illustration may be different,
check dimensions

Align front camera with retainer plate symmetrically with respect to the 3M privacy
Þ Illustration may be different, check dimensions -Bottom-).
film (⇒
2.2.5
2.3

Press front camera with retainer plate firmly onto the 3M privacy film on the windshield.

Routing wire harness
2.3.1

On the connector side, push one protective foam roll onto the wire harness for the
front camera retainer plate and the (3-wire) wire harness.

2.3.2

Make the plug connection (6-pin) under the roof lining.

2.3.3

Guide wire harness for front camera (dashcam) vertically with respect to the
headliner/roof console.

2.3.4

Push protective foam roll over the (6-pin) plug connection.
Secure (6-pin) plug connection and connection for front camera wiring harness
to existing components/lines under the headliner in the roof console area with
tie-wraps. Protective foam roll must also be wrapped around the connection.

Mar 24, 2026
Page 8 of 20

Tequipment

911 (992)

Installation and Conversion Instructions
2.4

18 / 22 ENU

9163

9

Connect electric wire harness coming from DashCam to wiring harness preparation
Function/line:

Connection point

Power supply

Connecting wiring harness to connection point preparation

Left fuse box

Right front fuse box, fuse holder J, slot F4
Mini 5A fuse

2.4.1

Connect power supply accordingly.

2.4.2

Protect the power supply to the front camera with a new fuse slot row F4 with a mini
5A fuse.
Fuse: Setpoint value 5 A

3

Rework roof console trim panel using a round file. Cable MUST run vertically in each variant, adapting
the trim panel accordingly.

File down the area around the line output.
3.1

File down mirror cover using a round file. Prepare a cable guide depending on the country
variant.

3.2

Install roof trim panel. ⇒ Workshop Manual 'Removing and installing roof trim panel'

3.3

Install roof console. ⇒ Workshop Manual 'Removing and installing front roof console'

3.4

Clean inside and outside of the windshield.

For Cabriolet/Targa variant, continue with Step 5. Coupé - continue with Step 4.
4

Install rear dashcam.
4.1

Remove roof trim panel in the rear window area. ⇒ Workshop Manual 'Removing and installing
roof trim panel'

Tequipment

Mar 24, 2026
Page 9 of 20

9

911 (992)
9163

ENU 18/22

4.2

Remove roll-over bar (if installed). ⇒ Workshop Manual 'Removing and installing roll-over
protection bar'

4.3

Installation position and cable routing.

1
2
3
4.4

Mar 24, 2026
Page 10 of 20

Installation and Conversion Instructions

Installation position and line routing
– Installation position of dashcam
– In the retaining strap holder area, pull a Teflon hose (in the set of materials) over the
dashcam wire harness.
– Disconnection point

Dashcam positioning, dimensions based on the rear window edge.

Tequipment

Installation and Conversion Instructions

A
B
C
4.5

911 (992)
18 / 22 ENU

9163

9

Dimensions for rear camera
– 138 mm / 5.43 in to lower edge
– 494 mm / 19.44 in at a right angle to rear window edge
– 497 mm / 19.56 in at a right angle to rear window edge

Installing rear camera (dashcam) on rear window

NOTICE
Adhesive films not prepared/installed correctly
•

Damage to adhesive films

•

Inadequate adhesion of adhesive films

Þ
⇒

Carefully clean the areas on which you intend to stick the film to ensure that all traces of oil, grease and
silicone are completely removed.

Þ
⇒

Do not touch the bonding surfaces.

Þ
⇒

Object (adhesive film, vehicle, etc.) and ambient temperature: Minimum temperature 15°C / 59 °F.

Tequipment

Mar 24, 2026
Page 11 of 20

9

911 (992)

Installation and Conversion Instructions

ENU 18/22

9163

4.5.1

Pull 3M privacy film off the backing
Þ Bonding on backing sheet
sheet (⇒
-A-).
1
2

– 3M privacy film
– Marked bonding surface

4.5.2

Position the 3M privacy film on the
marked bonding surface on the rear
Þ Bonding on backing
window (⇒
sheet -B-) and stick it on.

4.5.3

Carefully affix 3M privacy film using
a plastic squeegee, starting from the
center and moving towards the edge.

4.5.4

Remove the protective film from the rear camera mounting plate.

Bonding on backing sheet

Align rear camera with retainer plate symmetrically with respect to the 3M privacy
film.

Coding:

5

4.5.5

Press rear camera with retainer plate firmly onto the 3M privacy film on the rear
window.

4.5.6

Route wiring harness and secure with a tie-wrap.

4.5.7

Install roll-over bar (if installed). ⇒ Workshop Manual 'Removing and installing
roll-over protection bar'

4.5.8

Install roof trim panel in the rear window area. ⇒ Workshop Manual 'Removing and
installing front roof console'

Code the PORSCHE front camera (dashcam) in Dealer mode
5.1

Preparatory work
1
2
3
4
5
6

Mar 24, 2026
Page 12 of 20

– PORSCHE front camera
– Micro SD memory card (32 GB)
– Retainer plate
– Power button
– WiFi status LED display
– PRESS (release button)

5.1.1

Remove micro SD memory card (32
Þ DashCam overview -2-) from
GB, ⇒
card slot for front camera.

5.1.2

DashCam overview
With the ignition switched on, push
Þ DashCam overview -1-) into the retainer plate on the
the front camera (dashcam ⇒
Þ DashCam overview -3-)
windshield (⇒

Tequipment

Installation and Conversion Instructions

5.2

911 (992)
18 / 22 ENU

9163

9

5.1.3

Þ DashCam overview -4-) for 10 seconds until you hear the
Press the power button (⇒
second double beeping sound.

5.1.4

Þ DashCam overview
The front camera (dashcam) starts in Dealer mode: WiFi LED (⇒
-5-) lights up “yellow”.

Connect the front camera (dashcam) to the device (tablet, smartphone or PC)
Information
The "Dealer mode" network ID name ends with a "D". A password is NOT required!
The language setting can be changed by following the menu prompts after opening
the first page.
5.2.1

Search available networks for Dealer mode WiFi.

5.2.2

Open Dealer mode on the device (tablet, smartphone or PC) using any browser.
To do this, enter “192.168.1.1/diagnostics” in the browser’s address line.

5.2.3

Displays in “Dealer mode” main menu:
Options:
1
2