GROUP

NUMBER

CAMPAIGN

26-01-015H

DATE

Technical Service Bulletin

MODEL(S)

FEBRUARY 2026

SANTA FE (MX5A)

FPM SOFTWARE UPDATE
(LIMITED COVERAGE CAMPAIGN LA6)

SUBJECT:

 IMPORTANT
Dealers must perform this field action on all affected vehicles within 5 / 60,000 New Vehicle Limited
Warranty (NVLW) prior to customer retail delivery and whenever an affected vehicle is in the shop
for any maintenance or repair. See Warranty Information section for more details.
Access the “Vehicle Information” screen via WebDCS to verify “Warranty Start Date” and ensure the
vehicle is within NVLW, observing mileage prior to any repair work.
Description: Certain Santa Fe (MX5A) vehicles may experience a discharged battery condition due to
the Fingerprint Module (FPM) not entering 'SLEEP' mode when the ignition is turned off. This bulletin
provides instructions to perform a software update with revised logic for the FPM.
Applicable Vehicles (Certain):
Model Year

Model

Production Dates

2024 - 2025

Santa Fe (MX5A)

12/28/2023 – 02/10/2025

SST Information
Tool Name

Tool Number

VCI 3

G0VHNNN06

19-Pin Cable

Figure

Remarks

Ordering Information

+

VCI 3 comes with
the 19-pin cable
(P/N G1XDDCA020
included here
for reference)

Website:
https://hyundaiessentialtools.com/

G1XDDCA020

Email:
[email protected]

VCI 2
Ethernet
Communication
Interface (ECI)
Kit

G1XDDMN001

+
G0XDDMN052

If using VCI 2, the
ECI Kit will be
required to
complete software
updates.

Phone: 1-855-763-9199
Hours: 7 AM – 7 PM CST

Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

SUBJECT:

GDS Information:
System

Event Number

Description

FPM

1280

MX5A/MX5A HEV/MX5 HEV FPM LOGIC IMPROVEMENT

(*or use a later available event as listed in the GDS FPM Update screen if one is available.)
NOTE: The software update is subject to an OTA (Over-the-Air) option and may be completed by
customers with active Bluelink subscriptions.

Warranty Information:
Model

Op. Code

Operation

Op.
Time

Causal Part

Nature
Code

Cause
Code

Santa Fe
(MX5A)

50DA56R0

FPM Software Update

0.4
M/H

955C0-P6000

I11

ZZ3

NOTE 1: Submit claim on Claim Entry Screen as “Campaign” type.
NOTE 2: If any part(s) not subject to this TSB are found in need of replacement while performing the
repair procedure, and the affected part(s) are still under warranty, the dealer may submit a separate
claim using the same repair order. If the part(s) not subject to this TSB are out of warranty coverage,
the dealer has the option to submit a PA Request for goodwill consideration on a case-by-case basis.
NOTE 3: This TSB includes repair validation photos. Op times include VIN, mileage, and photo
capture of the ECU Update “Success” screen as outlined in the Digital Documentation Policy.

ROM ID Information:
Model

Event

System

ECU
Part Number

Santa Fe
(MX5A)

1280

FPM

955C0-P6000

TSB #: 26-01-015H

ROM ID
Old
1.00
1.10
1.20
1.30
1.40

New

1.80

Page 2 of 8

SUBJECT:

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

Service Procedure:

DIGITAL DOCUMENTATION
This TSB includes repair validation photos. Refer to the latest Warranty Digital Documentation
Policy for requirements.

NOTICE
You must initially perform the GDS ECU update in Auto Mode.
• If the ECU update starts but then fails in Auto Mode, perform the update in Manual Mode
to recover.

NOTICE
Ensure the vehicle’s battery charge is above 11.0 Volts and the tablet’s battery charge is above
30% before performing a software update to avoid update failure.

i

Information

•

Turn OFF all lamps (do NOT leave head lamp switch in auto mode) and all accessories.

•

Perform update with the ignition switch in the ON position.

•

Do NOT disconnect any cables connected to the vehicle or scan tool during the update.

•

Do NOT start the engine OR place in Ready mode during the update.

•

Do NOT turn OFF the ignition switch during the update.

TSB #: 26-01-015H

Page 3 of 8

SUBJECT:

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

Configuration of Ethernet Communication on Tablet PC

i

Information

Refer to TSB 23-GI-006H for detailed information on configuring Ethernet communication for
setup.
1.

Connect the Ethernet Communication
Interface (ECI) DLC cable to the OBD
connector of the vehicle.

2.

Connect the VCI DLC cable to the ECI.

3.

Select the appropriate tablet cable
(type C, 5-pin) to the ECI.

4.

Connect the cable to the tablet PC.

i

Information

The connection between the VCI 2 and tablet PC is wireless, whereas the tablet PC is connected
to the vehicle through the ECI (Ethernet adapter).
If using the VCI 3, the ECI is NOT needed. Connect the tablet directly to the VCI 3 using the
USB-C to 19-Pin Cable supplied in the VCI 3 Kit.

TSB #: 26-01-015H

Page 4 of 8

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

SUBJECT:

ECU Update Procedure
1.

Perform the ECU update in Auto Mode.

i

Information

Refer to TSB # 25-GI-011H, “ECU
Update Procedure for Tablet-Based
GDS-Smart,” for additional information.

2.

Select the FPM system to scan the vehicle’s
current ROM ID.

NOTICE
Check the current ROM ID version and
compare it to the ROM ID Information
table before attempting to perform the
software update.

NOTICE
If the update fails, remove the power
connector from the in-cabin fuse box for
at least 5 seconds. Reassemble and
retry the update.

TSB #: 26-01-015H

Page 5 of 8

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

SUBJECT:

3.

After the ECU update process shows 100%
complete, follow the prompts on the screen to
cycle the ignition OFF for at least 10 seconds
to reset the control unit (certain models may
take up to 30 seconds).

i

Information

Use the Refresh button to reset the
timer.

4.

OTA initialization should perform
automatically:
• If OTA initialization performs
automatically, then proceed with the
service procedure.

•

If the OTA initialization process fails,
complete it manually under:
S/W Management > CCU_CCNF Central Communication Unit (CCNF)
> OTA Initialization (A).
Follow the instructions on the screen.
A

TSB #: 26-01-015H

Page 6 of 8

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

SUBJECT:

5.

DIGITAL
DOCUMENTATION

Using the tablet or GDS screen capture
function, take a screenshot of the ECU
update "Success" result screen.
Upload the photo to STUI.
NOTE: The VIN/Date/Time/Mileage photo
imprint is NOT required for GDS
screenshots.

6.

Perform an All Systems Fault Code search
and erase DTC history that had incidentally
occurred from the ECU update.

7.

Disconnect the power connector of the indoor
fuse box, wait at least 5 seconds, then
reconnect it.

i

Information

Alternatively, disconnect the negative (–)
12V battery terminal, wait 5 seconds,
then reconnect it.

TSB #: 26-01-015H

Page 7 of 8

SUBJECT:

FPM SOFTWARE UPDATE (LIMITED COVERAGE CAMPAIGN LA6)

8.

Start the engine to confirm proper operation of
the vehicle.

9.

The service procedure is now complete.

NOTICE
If the ECU update fails in Auto Mode, perform the update in Manual Mode using the password(s)
below.
Manual Mode Password:
Event

Menu

Password

1280

MX5A/MX5A HEV FPM 955C0-P6000

0559

TSB #: 26-01-015H

Page 8 of 8