Technical Service Bulletin (TSB)
Flash: Battery Pack Control Module (BPCM) Updates
REFERENCE:

TSB: 08-039-26
GROUP 08 - Electrical

Date:

February 4, 2026

VEHICLES
AFFECTED:

2023 (JL) Jeep Wrangler
This bulletin applies to vehicles equipped with a 2.0L I4 DOHC DI
Turbo PHEV Engine (Sales Code ECX).

REVISION: —

MARKET APPLICABILITY:
NA

IAP

EE

MEA

SA

CH

NOTE: This bulletin applies
to the North America,
Enlarged Europe, Middle
East & Africa, China
and India & Asia Pacific
markets.
CUSTOMER
SYMPTOM:

Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must
exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs):
● P0B28-00 - Hybrid/EV Battery “B” Voltage Unstable.
● P0BBE-00 - Hybrid/EV Battery Pack Voltage Variation.
● P0AA1-00 - Hybrid/EV Battery Positive Contactor “A” Stuck Closed.
● P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long.
● P0CA6-00 - Hybrid/EV Battery Charging Current High.
● P0B24-00 - Hybrid/EV Battery "A" Voltage Unstable.
● P1C5E-00 - Hybrid/EV Battery State Of Health Failed.
● P0DAB-00 - Hybrid/EV Cell Balancing Performance.
● P0607-00 - ECU Internal Performance.
Customers may also comment on the following:
● Vehicle does not start.
NOTE: The no start condition is accompanied with the following DTCs: P0DAB-00, P0607-00, P0AA1-00,
P0AA4-00, P0C78-00, P0CA6-00, P0B24-00 and/or P1C5E-00. P0B28-00 will result in a MIL for 49
days. After 49 days of the MIL, the vehicle will no longer be allowed to start.

CAUSE:

BPCM software

M08 FSAR-TSB-6894

-2-

REPAIR SUMMARY:
This bulletin involves reprogramming the BPCM with the latest available software.
NOTE: Additional module flashes are required for this update to be effective, the following modules
are all to be updated along with this BPCM update:
● Powertrain Control Module (PCM).
● Integrated Dual Charging Module (IDCM).
● Transmission Control Module (TCM).
● Auxiliary Hybrid Control Processor (AHCP), Hybrid Control Processor (HCP) also known as
the Power Inverter Module (PIM).
CLAIMS DATA:

Labor Operation No:
18-19-87-AU

Failure Code

Labor Description
Battery Pack Control
Module (BPCM) Reprogram
(0 - Introduction)
CC

Skill Category
6 - Electrical and Body
Systems

Labor Time
0.3 Hrs.

Customer Concern

The dealer must use failure code CC with this Technical Service Bulletin.
● If the customer’s concern matches the SYMPTOM identified in the Technical Service Bulletin, failure code
CC is to be used.
● When utilizing this failure code, the 3C’s (customer’s concern, cause and correction) must be provided for
processing Technical Service Bulletin flash/reprogramming conditions.
DIAGNOSIS:
Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in DealerCONNECT/
Service Library, verify all related systems are functioning as designed. If DTCs or symptom conditions, other
than the ones listed above are present, record the issues on the repair order and repair as necessary before
proceeding further with this bulletin.
If the customer describes any of the symptoms listed above in the customer symptom section, perform the
Repair Procedure.
SPECIAL TOOLS/EQUIPMENT:

Description
wiTECH or Equivalent

Ref. No.
–

Notes
–

-3-

M08 FSAR-TSB-6894

REPAIR PROCEDURE:
NOTE: The IDCM, PCM, AHCP/HCP and TCM must be updated to the latest available software at
the conclusion of this repair procedure. Refer to all applicable published technical service
bulletins for detailed repair procedures and labor times regarding updating the IDCM, PCM,
HCP / AHCP and TCM software.
CAUTION!
Failure to update the IDCM, PCM, AHCP/HCP and TCM module following an HCP and AHCP software
update may result in vehicle malfunctions.
WARNING!
● Before performing the software reprogramming, it is necessary to make the vehicle safe.
● When performing repairs that directly involve or imply possible contact with live high voltage
components/systems, the technician must ensure that the power supply of the high-voltage system
is disconnected throughout the operation.
● Only specifically trained technicians qualified to perform repairs on vehicles with high voltage
systems under current national laws/regulations are authorized to work on the vehicle.
● Before performing any diagnostic repair work on the vehicle, carefully read and comply with
the general instructions for working safely on hybrid/electric vehicles and use suitable general
equipment and Personal Protective Equipment (PPE).
NOTE: Install a battery charger to maintain a 12 volt system voltage.
NOTE: If this flash process is interrupted/aborted, the flash should be restarted.
1. Disable HV Battery Contactors using wiTECH - Go to the Misc Functions tab --> Select Disable HV Battery
Contactors --> then follow the wiTECH prompts.
2. Use wiTECH to confirm that the contactors are open and waiting five minutes. If the contactors do not
open turn the ignition on then off. Once successful a note will appear on the wiTECH screen indicating the
contactors are open.
3. Reprogram the BPCM with the latest software. If issues arise when flashing a module using the wiTECH
Diagnostic Application, please submit a ticket to the Helpdesk. The helpdesk can be found within the Help
menu.
4. Clear all DTCs that may have been set in any module due to reprogramming. The wiTECH application will
automatically present all DTCs after the flash and allow them to be cleared.
5. Enable HV Battery Contactors using wiTECH - Go to the Misc Functions tab --> Select Enable HV Battery
Contactors For Service--> then follow the wiTECH prompts.
6. Verify the IDCM, PCM, AHCP/HCP and TCM are also programmed with the latest available software.
Refer to all applicable published service bulletins for detailed repair procedures and labor times regarding
updating the IDCM, PCM, AHCP/HCP and TCM software.
POLICY:
Reimbursable within the provisions of the warranty.
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.