TECHNICAL INSTRUCTIONS
FOR
SPECIAL SERVICE CAMPAIGN 26TD01

Front Spoiler Hardware
Certain 2025 Model Year 4Runner and 4Runner HV

The repair quality of covered vehicles is extremely important to Toyota. All dealership
technicians performing this recall are required to successfully complete the most current
version of the E-Learning course “Safety Recall and Service Campaign Essentials”. To
ensure that all vehicles have the repair performed correctly; technicians performing this
repair are required to currently have completed the following courses:
•

TIC206A – Electrical Repair I

Always check which technicians can perform the repair by logging on to
https://toyotacertification.com/certlogin.jsp. It is the dealership’s responsibility to select
technicians that have completed the above courses to perform this repair. Carefully
review your resources, the technician’s skill level, and ability before assigning
technicians to this repair. It is important to consider technician days off and vacation
schedules to ensure there are properly trained technicians available to perform this
repair at all times.

I.

OPERATION FLOW CHART

The flow chart is for reference only. DO NOT use it in place of the full technical instructions. Follow ALL
steps as outlined in the full technical instructions to confirm the campaign is completed correctly.

II. IDENTIFICATION OF AFFECTED VEHICLES
1. CHECK VEHICLE FOR CAMPAIGN ELIGIBILITY
a. Compare the vehicles VIN to the VIN listed on the Repair Order to ensure they match.
b. Check the TIS Vehicle Inquiry System to confirm the VIN is involved in this recall, and that it has not already
been completed.
NOTICE:
TMNA warranty will not reimburse dealers for repairs completed on vehicles that are not affected or were
previously completed, even by another dealer.

III. PREPARATION
A. Parts
Part Number

Part Description

Quantity

04005-35106

BOLT KIT

1

* The kit above includes the following parts.
Part Number

Part Name

Quantity

90105-06325

BOLT, WASHER BASED HEAD

7
1

90179-06349

NUT

7

B. TOOLS & EQUIPMENT
•
•

Standard Hand Tools
Plastic Trim Tools

•

¼” Torque Wrench

IV. BACKGROUND
Some of the screws holding the front spoiler to the front bumper can become loose over time and the spoiler can partially
detach at the outer edge of the vehicle. In some cases, the front spoiler can rub against other vehicle components
during driving and cause an intermittent noise.

2

Example of damaged spoiler

Create a documentation only
TAS case (DC designation) with
the following information to get
direction from your FTS.

Example of damaged bumper

Create a documentation only
TAS case (DC designation) with
the following information to get
direction from your FTS.
Damage to the front spoiler
caused by impact of road
debris and/or curbs is not
covered under this LSC.

3

Example of aftermarket bumper

Provide hardware to customer.

Example of no spoiler

Provide hardware to customer.

4

V. REPAIR PROCEDURE
1. REMOVE THE FRONT SPOILER ASSEMBLY
a) Locate and remove the 9 front spoiler bolts.

1

DO NOT DISCARD BOLTS OR REMOVE CLIPS IN LOCATIONS SHOWN ABOVE AND
DESIGNATED WITH YELLOW CIRCLES. THESE BOLTS AND CLIPS WILL BE REUSED.

DO NOT DISCARD 2 OF THESE BOLTS

DISCARD ALL OF THESE BOLTS

5

2. REMOVE BOTH SPOILER RETAINERS
a. Using a plastic trim tool, remove both spoiler retainers.
b. Once the front spoiler is removed, place in a safe location to avoid damage.

3. REMOVE LOWER 10mm FRONT FENDER LINER BOLT LH/RH
a. Remove the 10mm bolt for the lower front fender liner for the LH and
RH sides as shown in image. This bolt will be reused on both sides
and reinstalled in step 7.

6

4.

REMOVE 7 BUMPER CLIPS

NOTE: LOCATIONS WHERE BOLTS ARE REUSED DO NOT HAVE METAL BUMPER CLIPS. DO NOT
ATTEMPT TO REMOVE THESE RETAINERS.
a. Remove 7 bumper clips

5. INSTALL 7 NEW BUMPER CLIPS
a. Install 7 new bumper clips
NOTE: ENSURE NEW CLIPS ARE USED. DO NOT REUSE THE OLD
BUMPER CLIPS.
OLD

NEW

7

6. REINSTALL FRONT SPOILER
a. Insert the centering pin to align the spoiler with the front bumper, then install the LH and RH retainers.

b.
c.

Reinstall the 10mm bolt for the lower front
fender liner for the LH and RH sides.
Tighten bolt until snug.

NOTE: DO NOT OVERTIGHTEN BOLTS.

8

7. Install the (7) NEW bolts to on front spoiler by hand.
a. Torque all the (7) bolts to 6.5 Nm (58 in lb) EXCEPT the bolts circled in yellow.

b. Tighten the two bolts in yellow circles above until snug
NOTE: Do not overtighten the two bolts that are circled in YELLOW.
−
−
−
−

◄ VERIFY REPAIR QUALITY ►
Confirm new bumper clips are installed correctly
Confirm bolts are torqued to proper specifications
Confirm fender liners are secure
If you have any questions regarding this Campaign, please contact your regional representative

VI. APPENDIX
A.

CAMPAIGN DESIGNATION DECODER

Examples:
19TA01 = Launched in 2019, Toyota, Safety Recall Remedy Phase, 1st Safety Recall Launched in 2019
20TC02 = Launched in 2020, Special Service Campaign, 2nd Special Service Campaign Launched in 2020
21TE05 = Launched in 2021, Customer Support Program, 5th Customer Support Program Launched in 2021

9