Connection offline
Technical Service Bulletin

Transaction No.: 2080413/3

91-25-06 - Front Assist Not Available and/or ACC Temporarily Disabled

Condition
Applicable Vehicles
Year

Eng. Code

Trans. Code

VIN Range
From

VIN Range To

Atlas

2024-2026

All

All

All

All

Atlas Cross
Sport

2024-2026

All

All

All

All

fo
ri

nt

er

na

lu

se

.

Model(s)

ly

Revision Table
Published Date

Version Number

2080413/3

1/27/26

91-25-06

To update incorrect GFF labor
operation number

2080413/2

1/2/26

91-25-06

To update incorrect bulletin sequence
(version) number

2080413/1

12/17/25

91-25-04

Original publication.

lu
si

ex
c
e
ar

en
ts

do
cu

m

Reason For Update

ve

Instance Number

NOTICE

es
e

.

?:

Th

If software updates are performed on a vehicle, a charger with at least 70A charging current MUST be
used in order to avoid problems during software updates and flash campaign/actions.

The following fault code must be stored in the AW0013 Front Radar for Driver Assistance System -J428-.
If the code below is not present this bulletin does not apply and will not be covered under warranty.

DTC

Description

C110300, Symptom (791)

Adaptive Cruise Control sensor misadjusted

C110300, Symptom (204873)

Adaptive Cruise Control sensor misadjusted

NOTICE
DO NOT diagnose or replace the -J428- ACC module 0013 before per forming the updated function as
explained in this bulletin.

Technical Background
In certain highway scenarios the elevation performance is less adequate if there are low locations affecting
the drift of elevation angle which results in setting of C110300.
New software for front radar (ACC) with more robust auto-calibration algorithm for vertical misalignment.

se

.

Production Solution

lu

Not applicable.

er

na

Service

ly

fo
ri

nt

Update-Programming Procedure:

lu
si

ve

WARNING

en
ts

ar

e

ex
c

Critical Warning: The Midtronics battery charger must be connected to the vehicle battery for the duration
of the programming, to ensure the battery state of charge remains above 12.5 volts during the update
process. If the battery drops below 12.5 volts, the programming could fail which may result in damage to
the control module. Control modules damaged by inadequate voltage will not be covered under the
warranty policy. The technician should verify the vehicle voltage prior to starting the update process, and
should monitor the voltage for the duration of the programming.

do
cu

m

– The procedure may cancel itself if the hazard warning lights are not switched On. The hazard warning
lights prevent the system from switching to bus sleep mode during the update.

?:

Th

es
e

– ODIS-Service tester should be updated to the latest GFF technical version 25.1.1 or higher and SW
version 2.54.13 or higher.

NOTICE
Prior to launching the ODIS Service diagnostic applications and starting control module update process,
confirm the tester screen saver and power settings in accordance with Diagnostic Device Hardware &
Windows® - VHW-20-02 Change Power Options After Windows®10 Upgrade. Failure to do so may result
in the tester entering power save mode during data transfer, and subsequent control module failure. When
using a VAS 6150/X or 6160/X tester in conjunction with a VAS6154 wireless transmitter head for a flash
procedure, connect a USB cable between the transmitter head and the tester. Failure to do so may lead to
errors during the flash procedure.
– VAS tools must only be used with their power adapters plugged in. Under no circumstances should
they be used on battery power alone during the programming procedure.

To Update-Programming using Software Version Management (SVM), review and follow instructions in
Technical Bulletin Instance 2014603 “Software Version Management”.
The SVM process must be completed in its entirety, so the database receives the update confirmation
response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim
or action is carried out that is not explicitly stated in the Technical Bulletin.

•

Update the Engine Control Module using the SVM Unit code as listed in the table below:

Engine

Old Software Part
No.

Old
Software
Version

New Software
Part No.

Atlas

All

5WA.907.572.C

0461

5WA.907.572.C

Atlas Cross
Sport

All

5WA.907.572.C

0461

5WA.907.572.C

New
Software
Version (or
higher)

SVM Unit
Code

0464

5293

0464

5293

fo
ri

nt

er

na

lu

se

.

Model

e

ex
c

lu
si

ve

ly

The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.

After the Software update please reactivate the ACC function in the MFI/MIB menu and road test the
vehicle to validate system operation.

?:

Warranty

Th

es
e

•

do
cu

m

en
ts

ar

The procedure can be found in GFF under Functions/Component Selection, Software Version Management,
Adapting Software.

Active VW Customer Mobility Program (VWCMP) loaner vehicles are eligible to receive $35 per day for
loaner expense reimbursement under warranty (refer to document VWS-14-03 for applicable labor
operation).

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
Procedures Manual 1)
Model(s)

Year(s)

Eng. Code(s)

Trans. Code(s)

VIN Range
From

VIN Range
To

Atlas

2024-2026

All

All

All

All

Atlas Cross
Sport

2024-2026

All

All

All

All

SAGA Coding
Use applicable Claim Type 1)

Claim Type:

Damage

Service Number:

Code
0039

-WWO 2)

Atlas Cross Sport

VOA 2)

.

Atlas, Atlas Cross Sport

se

Parts Manufacturer

--

lu

9163

HST

Damage Location
(Depends on
Service No.)

01500010 = See Elsa for latest time units

Labor Operation 3): Update Programming Driver
Assistance Control Module

GFF time with a max of 50 TUs

ve

ly

fo
ri

nt

er

na

Labor Operation 3): GFF/Guided functions (including
Battery charge)

ex
c

lu
si

Diagnostic Time 4)

01500060 = Actual GFF
print out with a max of
50TUs

YES

en
ts

ar

e

GFF Time expenditure

do
cu

m

Road Test

YES

01320000 = 00 TU max.

NO

es
e

Technical Diagnosis

01210004 = see Elsa
for latest time units

Th

Claim Comment: Input “As per Technical Bulletin 2080413” in comment section of Warranty Claim.
Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only.

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

?:

1)

Required Parts and Tools
No Special Parts required.
No Special Tools required.

Tool Description

Tool No:

Midtronics Battery Tester/Charger

MYRMSP0702 battery maintainer/charger

VAS Diagnostic Tool

VAS 6150/X & VAS 6160/X with
ODIS Service with current online updates

* Call Volkswagen Tools and Equipment Program, Snap-On® Business Solutions (SBS at 1-800-892-9650
for product.

Additional Information

er

na

lu

se

.

All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.

?:

Th

es
e

do
cu

m

en
ts

ar

e

ex
c

lu
si

ve

ly

fo
ri

nt

© 2026 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is
based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors.
All rights are reserved to make changes at any time without notice. No part of this document may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites,
without the prior expressed written permission of the publisher.