SERVICE BULLETIN
Subject: TS35 Camera Connection
Improvement

Bulletin Type: Field Fix Conditional

Bulletin No: TS35-FC-2501

PQR No: 500000007779

Rev No: 00

Ref. No: 700004856

Vehicle Model: TS35

Flat Rate Time / Code: 60 min.

Date of issue: 24.12.2025

Modify Before: 24.12.2028

What to do with off coming parts:

What to do with outstanding parts of previous
revision:

☒Scrap
☐Return
☐Use with additional parts
☐On consignment
☐No off coming parts

☐Scrap
☒Return
☐Use with additional parts
☐On consignment
☐No outstanding parts

Modification Description: This bulletin aims to check and improve Camera connections.

Bulletin Responsible: Ahmet Altın

Published & Approved By: Esin Arısoy

SERVICE BULLETIN
SAFETY INSTRUCTIONS
1. Mechanical Requested Dress Code
WARNING:
 Dress properly to avoid personal injury and damage to the
vehicle
Always wear protective clothing
Do not wear any worn or loose-fitting clothing
Remove jewelry before starting to work
In case of long hair, use hairnet
The illustration on the left shows some of the correct and
incorrect clothing
 Sharp edged items should be avoided in order not to
scratch vehicle (i.e. belts, watches, necklace)






2. Protect Seats when Mechanic Starts Working

 Seats, trimming, upholstery stuff and carpeting should be
protected with appropriate coverings.

3. Welding on the Chassis
a. Always disconnect the batteries (starting with the negative lead).
b. Disconnect the connectors of electrical and electronic equipment (electronic control
units, sensors and actuators) if they are less than 2 meters away from the chassis
part to be welded or the earth terminal of the welding equipment.
c. The earth terminal should never be attached to vehicle components such as engine,
axles and springs. Arcing on these parts is not permitted, because of the risk of
damage to bearings, springs, etc.
d. The earth terminal must make good contact and be placed as close as possible to
the part to be welded.
e. Plastic pipes, rubber parts and parabolic springs should be well protected against
welding spatter and temperatures higher than 70°.
f. The contact switch must not be in the accessory or contact position. The contact key
should be removed.
g. Reconnect in reversed order of disconnecting. Ensure that a good earth connection
is made between chassis, engine and cab.

SERVICE BULLETIN
ADDED PARTS
No

Part No

Part Name

1

9404-94Y

2

Picture

Quantity

Unit

CABLE PROTEC.SLOTTED
SPIRAL PA6

5

meter

9402-96Y

T-MALE-0,5-1,0 mm2

1

piece

3

9402-78Y

T-MALE-0.75-1 mm2

2

piece

4

TH992002Y

TERMINAL, FEMALE

1

piece

5

9401-372

CABLE 1.0mm W-TXL

5

meter

6

9440-001Y

FUSE 3A AUTOMATIC

1

piece

7

RP554159

REAR VIEW CAMERA VEHICLE
CON. HARNESS

1

piece

8

64426-6003001Y

IZOLEBANT (19*33M*0.15)

1

piece

Quantity

Unit

1

piece

REMOVED PARTS
No

Part No

Part Name

1

HD554131Y

REAR VIEW CAMERA
MID-CABLE

Picture

SERVICE BULLETIN
APPLİCATİON STEPS
HARDWARE (HARNESS) APPLICATION
Application to be made in the Relay Panel Area


Open the vehicle's relay panel area.

Relay Panel

SERVICE BULLETIN
1) Cut 2 meters from cable number 9401-372.
2) Using a crimping tool, connect the 9402-78Y terminal to one end of the white cable
numbered 9401-372 and the TH992002Y terminal to the other end.

3) Connect the terminal of cable number 9401-372 to the empty pin of fuse number 100BH
located in the relay panel area.

SERVICE BULLETIN
4) Open the compartment containing the transition sockets in the luggage area on the relay
panel side of the vehicle.

5) Pass cable number 9401-372 through the slotted spiral. Pass the cable you connected to
the fuse through the gaps shown in the images below to the area where the transition
sockets are located. Remove the sealant from the gap opening into the luggage
compartment so that the cable can pass through.

SERVICE BULLETIN


Remove the white plug from the pin connected to the SP-08 cable (blue) in the F.BODY
labeled socket in this area. Connect the end of the numbered 9401-372 cable, with the
9402-78Y terminal to this pin.

6) Using a crimping tool, attach terminal 9402-96Y to one end of numbered 9401-372 3 meter
cable and terminal 9402-78Y to the other end.

7) Open the cover on the dashboard area of the front door of the vehicle. Find the socket
labeled F.BODY in this area.



Connect the end of the numbered 9401-372 cable you connected to terminal 9402-78Y to
the pin to which the SP-08 numbered cable is connected in this socket.

SERVICE BULLETIN
Numbered RP554159 Cable Harness


Remove the cover section under the dashboard by unscrewing the screws.

1) Locate the vehicle connection wiring for the rearview camera numbered HD554131Y
located in the front body area.

SERVICE BULLETIN
2) Find the RP999155 cable that connects to the camera, and disconnect the socket connection shown in the
diagram between the RP999155 and HD554131Y 6 pin S-Video Connector.

3) Disconnect the BNC connector of cable number HD554131Y from the Multiviu.

4) Disconnect the 4-pin socket connected to the vehicle wiring harness for cable number
HD554131Y.

SERVICE BULLETIN


The harness numbered HD554131Y will be scrapped.

5) Disconnect the power cable connected to the pin 2 of socket 9460-573 and isolate it on the
vehicle.
6) Take the numbered 9401-372 cable, which you previously connected to pin SP-08 in the
socket labeled F.BODY in the front door dashboard area, and route it from the front door
dashboard area to the steering wheel lower area through the slotted spiral, using the gap
shown in the image below.

7) Connect the end of the numbered 9401-372 cable connected to terminal 9402-96Y to pin 2
of socket 9460-573, which is connected to the vehicle wiring harness of cable HD554131Y.
8) Find the RP999155 cable on the device that connects to the camera. Connect the socket
connection shown in the figure between the RP999155 and RP554159, 6 pin S-Video
Connector.

9) Connect the four-pin socket numbered 929504-1 of the harness numbered RP554159 to
the socket numbered 9460-573.

SERVICE BULLETIN
10) Connect the BNC connector to the BNC input on the Multiviu.

11) Insert the 3A fuse into the 100BH fuse slot on the fuse panel.

SERVICE BULLETIN
DISTRIBUTION OF WORKING TIME
IMPLEMENTATION

Rear View camera hardware improvement
TOTAL

TIME
60 min
60 min

SERVICE BULLETIN
AFFECTED VEHICLE LIST
No
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.

Otpa No
OA18153
OA18152
OA18218
OA18219
OA18220
OA18240
OA18241
OA18346
OA18348
OA18347
OA18505
OA18504
OA18506
OA18507
OA18508
OA18528
OA18529
OA18535
OA18534
OA18530
OA18633
OA18634
OA18635
OA18666
OA18746
OA18747
OA18721
OA18748
OA18852
OA18862
OA18864
OA18863
OA18980
OA18981
OA18865
OA18866
OA18982
OA18983
OA18997
OA18984
OA18998