GROUP

NUMBER

CAMPAIGN
DATE

Technical Service Bulletin

25-01-090G
MODEL(S)

DECEMBER 2025

G80 (RG3)
GV80 (JX1)

CCP SOFTWARE UPDATE
(LIMITED COVERAGE CAMPAIGN L05G)

SUBJECT:

 IMPORTANT
Retailers must perform this field action on all affected vehicles within 5 / 60,000 New Vehicle Limited
Warranty (NVLW) prior to guest retail delivery and whenever an affected vehicle is in the shop for
any maintenance or repair. See Warranty Information section for more details. Access the “Vehicle
Information” screen via WebDCS to verify “Warranty Start Date” and ensure the vehicle is within
NVLW, observing mileage prior to any repair work.
Description: Certain G80 (RG3) and GV80 (JX1) vehicles may exhibit battery drain due to the Central
Control Panel (CCP) not entering sleep mode. This occurs when a communication error causes the
touch-module control IC and MCU to repeatedly reinitialize, preventing the system from entering sleep
mode. This bulletin provides instructions to perform a software update for the CCP.

Applicable Vehicles (Certain):
Model Year

Model

2025

Production Dates

G80 (RG3)

06/03/2024 – 09/10/2024

GV80 (JX1)

03/05/2024 – 08/26/2024

SST Information:
Tool Name

Tool Number

VCI 3

G0VPNNN006

Figure

Ordering Information

Website:
https://genesisessentialtools.com/
Email:
[email protected]

VCI 2

G1XDDMN002

Phone: 1-855-763-6630
Hours: 7 AM – 7 PM CST

NOTE: VCI 2 can NO longer be ordered but can be used for the updates in this TSB.

Circulate To: General Manager, Service Manager, Parts Manager, Warranty Manager, Service
Advisors, Technicians, Body Shop Manager, Fleet Repair

SUBJECT:

CCP SOFTWARE UPDATE

(LIMITED COVERAGE CAMPAIGN L05G

)

GDS Information:
System

Event Number*

Description

1298

JX1 PE CCP LOGIC IMPROVEMENT

1299

RG3 PE CCP LOGIC IMPROVEMENT

FPM
(*or use a later available event as listed in the GDS FPM Update screen if one is available.)
Warranty Information:
Model

Op. Code

GV80 (JX1)

50D216R0

G80 (RG3)

50D216R1

Operation

Op.
Time

CCP Software
Update

0.3 M/H

Causal Part

Nature
Code

Cause
Code

I14

ZZ3

96540-T6500NX4
96540-T1AA0NX4

NOTE 1: Submit claim on Claim Entry Screen as “Campaign” type.
NOTE 2: 5 / 60,000 New Vehicle Limited Warranty (NVLW) applies to the part(s) and repair
procedure(s) outlined in this TSB. Prior to beginning any repair work, ensure the part(s) associated
with the repair procedure are within NVLW, observing mileage and Warranty Start Date or date of first
use. If the subject part(s) are out of warranty coverage, the retailer has the option to submit a PA
Request for goodwill consideration on a case-by-case basis.
NOTE 3: If any part(s) not subject to this TSB are found in need of replacement while performing the
repair procedure, and the affected part(s) are still under warranty, the dealer may submit a separate
claim using the same repair order. If the part(s) not subject to this TSB are out of warranty coverage,
the retailer has the option to submit a PA Request for goodwill consideration on a case-by-case basis.
NOTE 4: This TSB includes repair validation photos. Op times include VIN, mileage, and photo
capture of the ECU Update “Success” screen as outlined in the Digital Documentation Policy.
ROM ID Information:
Model

GV80 (JX1)

Event

System

1298

ECU
Part Number

96540-T6500
FPM

G80 (RG3)

1299

96540-T1AA0

TSB #: 25-01-090G

ROM ID
Current

1.00
1.01
1.02
1.03
1.04
1.06
1.07
1.00
1.01
1.02
1.03
1.04
1.05

Latest

1.08

1.06

Page 2 of 6
SUBJECT:

SUBJECT:

CCP SOFTWARE UPDATE

(LIMITED COVERAGE CAMPAIGN L05G

)

Service Procedure:

DIGITAL DOCUMENTATION
This TSB includes repair validation photos. Refer to the latest Warranty Digital Documentation
Policy for requirements.

NOTICE
You must initially perform the GDS ECU update in Auto Mode.
• If the ECU update starts but then fails in Auto Mode, perform the update in Manual Mode
to recover.

NOTICE
Ensure the vehicle’s battery charge is above 11.0 Volts and the tablet’s battery charge is above
30% before performing a software update to avoid update failure.

i

Information

•

Turn OFF all lamps (do NOT leave head lamp switch in auto mode) and all accessories.

•

Perform update with the ignition switch in the ON position.

•

Do NOT disconnect any cables connected to the vehicle or scan tool during the update.

•

Do NOT start the engine during the update.

•

Do NOT turn OFF the ignition switch during the update.

TSB #: 25-01-090G

Page 3 of 6
SUBJECT:

SUBJECT:

1.

CCP SOFTWARE UPDATE

(LIMITED COVERAGE CAMPAIGN L05G

)

Perform the ECU update in Auto Mode.

i

Information

Refer to TSB # 25-GI-020G, “ECU
Update Procedure for Tablet-Based
Genesis Smart”, for additional
information.

2.

Verify the ROM ID by selecting the FPM
system to scan the vehicle’s current ROM ID.

NOTICE
Check the current ROM ID version and
compare it to the ROM ID Information
table before attempting to perform the
software update.

NOTICE
If the update fails, remove the power
connector from the in-cabin fuse box for
at least 5 seconds. Alternatively,
disconnect the negative (–) 12V battery
terminal, wait at least 5 seconds.
Reassemble and retry the update.

TSB #: 25-01-090G

Page 4 of 6
SUBJECT:

SUBJECT:

3.

CCP SOFTWARE UPDATE

(LIMITED COVERAGE CAMPAIGN L05G

)

After the ECU update process shows 100%
complete, follow the prompts on the screen to
cycle the ignition OFF for at least 10 seconds
to reset the control unit (certain models may
take up to 30 seconds).

i

Information

Use the Refresh button to reset the
timer.

4.

DIGITAL
DOCUMENTATION

Using the tablet or GDS screen capture
function, take a screenshot of the ECU
Update “Success” result screen.
Upload the photo to STUI.
NOTE: The VIN/Date/Time/Mileage photo
imprint is NOT required for GDS
screenshots.

TSB #: 25-01-090G

Page 5 of 6
SUBJECT:

SUBJECT:

CCP SOFTWARE UPDATE

(LIMITED COVERAGE CAMPAIGN L05G

5.

Perform an All Systems Fault Code search
and erase DTC history that had incidentally
occurred from the ECU update.

6.

Remove the power connector from the
in-cabin fuse box for at least 5 seconds, then
reconnect it.

i

)

Information

Alternatively, disconnect the negative (–)
12V battery terminal, wait at least 5
seconds, then reconnect it.

7.

Start the engine to confirm proper operation of
the vehicle.

8.

The service procedure is now complete.

NOTICE
If the ECU update fails in Auto Mode, perform the update in Manual Mode using the password(s)
below.
Manual Mode Password:
Event

ECM Menu

Password

1298

JX1 PE CCP 96540-T6500

6500

1299

RG3 PE CCP 96540-T1AA0

1515

TSB #: 25-01-090G

Page 6 of 6
SUBJECT: