T-SB-0047-25

July 31, 2025

2026 Sequoia HV Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2026

Sequoia HV

ADDITIONAL INFORMATION

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer
feedback indicates the following areas deserve special attention when performing PDS:


Careful inspection for paint chips/scratches and body dents/dings.



Proper operation of electrical accessories (including interior light, clock, and radio reset).



Interior cleanliness.



Proper function of mechanical systems.

The PDS process helps identify potential vehicle concerns before customer delivery. After
completing the PDS process, maintain accurate PDS records by ensuring the required
documents listed below are completed and recorded in accordance with Toyota Warranty Policy.


GTS+ Health Check.



Completed PDS Check Sheet.



Battery Charge Test Print Out.



GTS+ Tire Pressure Information.

Customer retention and proper maintenance of vehicles are and have always been a major focus
for Toyota. To help remind customers that regular service is essential to the proper maintenance
of the vehicle, dealers are required to install a service reminder sticker before delivery. By doing
this, customers will be reminded to return to your dealership for service. Your current service
reminder sticker may be used. (See PDS Check Sheet item 7 of “Final Inspection and Cleaning.”)

© 2025 Toyota Motor Sales, USA

Page 1 of 8

T-SB-0047-25

July 31, 2025

Page 2 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Introduction (continued)

This bulletin contains the PDS procedures that apply specifically to 2026 model year Sequoia
Hybrid vehicles.
Refer to T-SB-0023-25, the universal Check Sheet that contains PDS steps that apply to all 2026
model year Toyota vehicles. To properly perform a complete PDS, you must complete all
procedures contained in this TSB as well as the universal PDS Check Sheet. In addition, if the
vehicle is stored for over 30 days, refer to T-SB-0009-25, Long-Term Vehicle Storage Guidelines.
Refer to the table below for a definition of terms that may be used in this bulletin.
Table 1.
TERM

ACRONYM

Conventional Vehicle

CV

A vehicle with only a gasoline engine for propulsion

DEFINITION

Electrified Vehicle

EV

A vehicle that utilizes a hybrid, plug-in hybrid, fuel cell, or
battery electric system for propulsion

Hybrid Electric Vehicle

HEV

Plug-in Hybrid Electric Vehicle

PHEV

A vehicle with both a gasoline engine and a HV Battery that can
be charged externally

Battery Electric Vehicle

BEV

A vehicle with only a HV Battery that can be charged externally

Fuel Cell Electric Vehicle

FCEV

A vehicle with both a hydrogen fuel cell and a HV Battery

State of Charge

SOC

The remaining capacity available in a battery

12-Volt

12V

Standard 12V battery used to power electrical systems separate
from high voltage components

High Voltage

HV

HV Battery used to power the electrified vehicle

A vehicle with both a gasoline engine and a HV Battery

© 2025 Toyota Motor Sales, USA

T-SB-0047-25

July 31, 2025

Page 3 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Table of Contents



Warranty Policy ........................................................................................................................ 4



Warranty Information ............................................................................................................... 4



Required Tools and Equipment ................................................................................................ 4



D/C Cut Fuse Installation ......................................................................................................... 5



Front License Plate and Mounting Bracket Installation* ........................................................... 6



Tire Pressure Warning System (TPWS) Initialization ............................................................... 6



Seating Position Control ECU Initialization ............................................................................... 7



Head Unit System Reset .......................................................................................................... 7



Dealer Contact Information for Call Dealer Head Unit Function* .............................................. 7



Navigation — Set Date & Time by GPS .................................................................................. 8
*If applicable.

© 2025 Toyota Motor Sales, USA

T-SB-0047-25

July 31, 2025

Page 4 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Warranty Policy

If the need for additional repairs or adjustment is noted during PDS, the required service should be
performed under warranty. Reimbursement will be managed under the warranty policy.
The Warranty Policy and Procedures Manual requires that you maintain the completed
Check Sheet in the customer’s file. If you cannot produce a completed form for each retailed
vehicle upon TMS and/or Region/Distributor audit, the PDS payment amount will be subject
to debit.
An additional Repair Order completed in conjunction with normal PDS MUST have time punch/flags
for service. If multiple repairs are performed, separate time flags MUST be punched for
each repair.

Warranty Information
OP CODE

DESCRIPTION

MODEL

TIME

OFP

T1

T2

001013

Pre-Delivery Service (PDS)

Sequoia HV

0.9

–

–

–

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream ADVi*
Techstream Lite

PART NUMBER

QTY

TSADVUNIT
ADE

Techstream Lite (Green Cable)

TSLITEPDLR01
TSLP2DLR01

*Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 GTS+ software version 2025.02.006.02 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE) at
1-800-368-6787 or by visiting TIS – Diagnostics – Tools & Equipment – Techstream Order Portal.

© 2025 Toyota Motor Sales, USA

1

T-SB-0047-25

July 31, 2025

Page 5 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

Check the location of the D/C cut fuse (30A). It may have been removed at the assembly plant
and temporarily stored in the blank space of the relay block in the engine compartment to
minimize battery discharge during transportation and storage.


If the D/C cut fuse (30A) is still in its original location in the relay block, proceed with
performing a Health Check using GTS+.



If the D/C cut fuse (30A) is NOT in its original location, it is necessary to remove the D/C cut
fuse (30A) from the blank space in the relay block and reinstall it to its original location as
shown. After installation, confirm ALL related DTCs are cleared.

Figure 1.

3
1

2

1

Relay Block

2

Remove the D/C Cut Fuse (30A) (Blank Space)

3

Install the D/C Cut Fuse (30A) (Original Location)

NOTE
 With the D/C cut fuse (30A) removed, if ANY DTCs are detected when the ignition is turned ON during
transportation, use GTS+ to clear ALL DTCs AFTER ensuring that there are NO malfunctions.
 While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to T-SB-0017-25, Battery Inspection and Maintenance During PDS, for
battery maintenance information.

© 2025 Toyota Motor Sales, USA

T-SB-0047-25

July 31, 2025

Page 6 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate bracket along with two long self-tapping and two short self-tapping screws
are loaded in the vehicle at the assembly plant. Follow this procedure to install the front license
plate mounting bracket and front license plate in states where it is required by law.
NOTICE
 Do NOT drill holes through the bumper.
 Do NOT overtighten screws.

1. Align the holes on the front license plate mounting bracket with the dimples on the front of
the bumper.
2. Install the two long self-tapping screws through the bracket securing the front license plate
mounting bracket to the front bumper.
3. Insert the license plate onto the tabs on the license plate mounting bracket.
4. Align the holes on the license plate with the holes on the license plate mounting bracket.
5. Install two short self-tapping screws through the license plate holes extending into the license
plate mounting bracket.

Tire Pressure Warning System (TPWS) Initialization

Refer to the applicable Repair Manual for the TPWS initialization procedure.


2026 Sequoia HV:
Suspension – Tire Pressure Monitoring – Tire Pressure Warning Receiver – Initialization
NOTE
 To adjust the tire pressure correctly when the outside temperature is significantly colder than shop
temperature, perform a Health Check using GTS+ and select the compensation tire pressure
checkbox. Compensation pressures will display on the Health Check results screen. Adjust the tire
pressure when the tires are cold.
 This model has four TPWS sensors.

© 2025 Toyota Motor Sales, USA

T-SB-0047-25

July 31, 2025

Page 7 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Seating Position Control ECU Initialization

Refer to the applicable Repair Manual for the seating position control ECU initialization
procedure (procedure 2).


2026 Sequoia HV:
Vehicle Interior – Seat –
Front Power Seat Control System (w/ Memory with Seat Vibration System) – Registration



2026 Sequoia HV:
Vehicle Interior – Seat –
Front Power Seat Control System (w/ Memory without Seat Vibration System) – Registration

Head Unit System Reset

Prior to vehicle delivery, please confirm that the welcome screen with language options appears
on the head unit display when ignition is switched to the ON position. There may be instances
where the welcome screen with language options may not properly appear on the head
unit display.
If the welcome screen showing language options is NOT displayed, complete the following steps:
1. Select the Settings option (gear icon).
2. Scroll down and select the Info & Security option.
3. The System Reset dialogue box will appear. Select Reset to confirm the resetting of system.
4. Confirm that the welcome screen with language options is now displayed.

Dealer Contact Information for Call Dealer Head Unit Function (Premium Audio Only)

Refer to the Multimedia System Owner’s Manual to add dealer contact information.


2026 Sequoia HV:
Section 2-9 Vehicle settings – Setting dealer information

© 2025 Toyota Motor Sales, USA

T-SB-0047-25

July 31, 2025

Page 8 of 8

2026 Sequoia HV Pre-Delivery Service (PDS)
Navigation — Set Date & Time by GPS

Prior to vehicle delivery, it is necessary to turn the Set Date & Time by GPS setting to the
ON position.
1. Turn the engine switch (power switch) to the ON position (ON mode).
2. Navigate the following menus in the head unit: Settings – General – Date & Time –
Set date & time by GPS.
3. Ensure the Set Date & Time by GPS function is set to the ON position.

© 2025 Toyota Motor Sales, USA