Technical Service Bulletin (TSB)
Partial Rear Window Molding Detachment
REFERENCE:

TSB: 23-024-25 REV. A
GROUP: 23 - Body

Date:

August 1, 2028

VEHICLES
AFFECTED:

2024 (FG) FIAT 500e
This bulletin applies to vehicles built on or after January 15, 2024
(MDH 0115XX) and on or before September 03, 2024 (MDH 0903XX).

REVISION: 23-024-25

MARKET APPLICABILITY:
NA

MEA

SA

IAP

EE

CH

NOTE: This bulletin applies
to the North America,
South America, Middle
East and Africa
and Enlarged Europe
markets.
CUSTOMER
SYMPTOM:

Customers may experience the following:
● Noise/vibration from rear side window while driving.

CAUSE:

Rear window trim not fully sealed to the body at assembly

This bulletin supersedes Technical Service Bulletin (TSB) 23-024-25, date of issue June 17, 2025,
which should be removed from your files. All revisions include removal of a Sales Code not
highlighted with **asterisks** and updated Spare Parts table.
This Technical Service Bulletin (TSB) has also been released as a Rapid Service Update (RSU) 25-111,
date of issue June 17, 2025. All applicable RSU VINs have been loaded. To verify this RSU service
action is applicable to the vehicle, use VIP or perform a VIN search in DealerCONNECT/Service Library.
All repairs are reimbursable within the provisions of warranty.
REPAIR SUMMARY:
This bulletin involves inspecting the rear side window trim molding and possibly replacing the window trim
molding if necessary.

M23 FSAR-TSB-6105

-2-

CLAIMS DATA:

Labor Operation No:
23-30-30-96

23-30-30-97

23-30-30-98

Failure Code

Labor Description
Inspect Left and Right
Quarter Glass Trim
Molding
(2 - Skilled)
Inspect and Replace
Quarter Glass Trim
Molding (One Side)
(2 - Skilled)
Inspect and Replace
Quarter Glass Trim
Molding (Both Sides)
(2 - Skilled)
ZY

Skill Category
6 - Electrical and Body
Systems

Labor Time
0.2 Hrs.

6 - Electrical and Body
Systems

0.4 Hrs.

6 - Electrical and Body
Systems

0.5 Hrs.

Part No.
68730931AA - MOPAR
52261019 - EMEA
68730989AA - MOPAR
52261020 - EMEA

Description
Molding, Right

Service Action

SPARE PARTS:

Qty
**1 (AR)
1 (AR)

Notes

Molding, Left**

DIAGNOSIS:
If a customer’s VIN is listed in VIP or your RSU VIN list, perform the repair. If any vehicle not on the VIN list
exhibits any of the symptom listed above in the customer symptom section, perform the Repair Procedure.
SPECIAL TOOLS/EQUIPMENT:

Description
Trim Stick
Gauges, Clearance Measurement,
Non-Metallic

Ref. No.
C-4829A
2022300230

Notes
Essential Tool
Essential Tool

-3-

M23 FSAR-TSB-6105

REPAIR PROCEDURE:
NOTE: Repair Procedure is to be performed on both side windows.
1. Inspect for correct attachment of the molding by pushing on the clip position shown in Fig. 1.

Fig. 1
Area On Trim Molding To Inspect
2. Using a feeler gauge with a measurement of 1.19 mm (3/64 in.) check the upper contact area of the
molding with the rubber gasket gap at the clip points. The gap must be less than 1.19 mm (3/64 in.).
NOTE: Be sure to pull on the molding to ensure adherence to the frame.
3. Does the gap exceed 1.19 mm (3/64 in.) or did the molding pull away from the mounting clips?
● YES >>> Proceed to Step 4.
● NO >>> This bulletin does not apply. Use Inspection LOP (23-30-30-96). Perform further diagnostics.
NOTE: Operation is the same for left or right side of the vehicle.
4. Open the front door.
5. Apply a double layer of paper tape to the body to protect the paint.
6. Using a trim stick, remove the trim from the seal clips and retaining clips then remove and discard the trim
Fig. 2.

Fig. 2
Trim Stick Locations For Removal Of Trim
1 - Trim Stick

M23 FSAR-TSB-6105

-4-

7. Check that the retaining clips and the seal clips are not damaged Fig. 3 and Fig. 4.

Fig. 3
Retaining Clip

Fig. 4
Seal Clip

-5-

M23 FSAR-TSB-6105

8. Put the NEW trim in place by first lining up the trim retainer on the door pillar side to the corresponding seal
clip Fig. 5.

Fig. 5
New Trim In Place
NOTE: First lock the lower profile of the trim followed by the upper profile until it clicks into place.
9. Position the trim so that it is parallel with the upper lip profile of the seal Fig. 6.

Fig. 6
Trim In Position
10. Secure the remaining retainers of the trim to the corresponding clips.

NOTE: Ensure the lower lip of the seal has not been pinched by the trim and remains positioned
outside the trim Fig. 7.

Fig. 7
Trim Installed
1 - Lower Lip Of The Seal
2 - Trim

NOTE: For SA market only, after applying this TSB, it is not necessary to send DID-I or DID-A.
POLICY:
Reimbursable within the provisions of the warranty.
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise, without written permission of FCA US LLC.