Connection offline
Technical Service Bulletin

Transaction No.: 2078469/1

37-25-01 - Transmission Control Module -J217-, DTC P0613 S/W Update

Condition
Applicable Vehicles
Model(s)
Atlas
FWD
Atlas
4MOTION

Year

Eng. Code
2.0T

2025

(DRKB)
2.0T

2025

Atlas Cross
Sport FWD

2025

Atlas Cross
Sport 4MOTION

2025

(DRKB)
2.0T
(DRKB)
2.0T
(DRKB)

Trans. Code

VIN Range From

VIN Range To

ALL

CA_SC000001

CA_SC571274

ALL

CA_SC000001

CA_SC570020

ALL

CM_SC000001

CM_SC228965

ALL

CM_SC000001

CM_SC228647

Revision Table
Instance Number Published Date Version Number Reason For Update
2078469/1

07/17/2025

37-25-01

Original publication.

One or more of the following fault code(s) must be stored in the - J217-Transmission Control Module:

DTC

Description

P0613

TCM Processor

NOTICE
One or more of the following symptom codes must be present:
– 42514, 42516, 42518, 42519, 42522, 42524, 42526, 42914, 42915, 42916, 42917, 42918, 42919,
42920, 43035, 43036, 43088, 43089, 43090, 43091

NOTICE
DO NOT diagnose or replace any components for the above fault(s) before performing the update function
as explained in this bulletin.

Technical Background
Improved fault code diagnosis to prevent erroneous fault code detection.

Production Solution
Improved TCM software implemented in production.

Service
Update-Programming Procedure:
WARNING
Critical Warning: The Midtronics battery charger with at least 70A charging current must be connected to
the vehicle battery for the duration of the programming, to ensure the battery state of charge remains
above 12.5 volts during the update process. If the battery drops below 12.5 volts, the programming could
fail which may result in damage to the control module. Control modules damaged by inadequate voltage
will not be covered under the warranty policy. The technician should verify the vehicle voltage prior to
starting the update process, and should monitor the voltage for the duration of the update.

WARNING
Radiator Fan(s) may cycle ON high speed during the Update Process! There is a risk that personal injury
may result if contact is made with spinning fan blades.
– Keep hands and objects away from Radiator Fan(s) during update process.

NOTICE
Prior to launching the ODIS service diagnostic applications and starting control module update process,
confirm tester screen saver and power settings in accordance with Special Tools and Equipment - Service
Information Circular # VHW-22-13. Failure to do so may result in the tester entering power save mode
during data transfer, and subsequent control module failure.
– When using a VAS 6150/X or 6160/X tester in conjunction with a VAS 6154/X wireless transmitter head
for a flash procedure, connect a USB cable between the transmitter head and the tester. Failure to do
so may lead to errors during the flash procedure. VAS tools must only be used with their power
adapters plugged in. Under no circumstances should they be used on battery power alone during the
programming procedure.

To Update-Programming using Software Version Management (SVM), review and follow instructions in
Technical Bulletin Instance 2014603 “Software Version Management”.

The SVM Process must be completed in its entirety, so the database receives the update confirmation
response. A warranty claim may not be reimbursed if there is no confirmation response to support the claim
or action is carried out that is not explicitly stated in the Technical Bulletin.

•

Update the -J217- Transmission Control Module using the SVM Unit code as listed in the table below:

Model

Engine

Atlas

2.0T

FWD

(DRKB)

Atlas

2.0T

4MOTION

(DRKB)

Atlas Cross
Sport FWD

2.0T

Atlas Cross
Sport
4MOTION

(DRKB)
2.0T
(DRKB)

Old Software
Part No.

09H 927 158 H

09H 927 158 J

09H 927 158 H

09H 927 158 J

Old
Software
Version
1507
1508
1507
1508
1507
1508
1507
1508

New Software
Part No.

New Software
Version (or
higher)

SVM
Unit Code

09H 927 158 H

1509

50B5

09H 927 158 J

1509

50B5

09H 927 158 H

1509

50B5

09H 927 158 J

1509

50B5

The procedure can be found in GFF under Functions/ Component Selection, Software Version Management,
Adapting Software.
Ensure attached ECM/TCM Tuning Form has been completed and signed by customer as required in SVM
Technical Bulletin Instance 2014603.

Warranty

To determine if this procedure is covered under Warranty, always refer to the Warranty Policies and
Procedures Manual (1)
Model(s)
Atlas
FWD
Atlas

Year

2025

Eng. Code
2.0T
(DRKB)
2.0T

Trans. Code

VIN Range
From

VIN Range To

ALL

CA_SC000001

CA_SC571274

4MOTION

2025

Atlas Cross
Sport FWD

2025

Atlas Cross
Sport
4MOTION

2025

(DRKB)
2.0T
(DRKB)
2.0T
(DRKB)

ALL

CA_SC000001

CA_SC570020

ALL

CM_SC000001 CM_SC228965

ALL

CM_SC000001 CM_SC228647

SAGA Coding
Use applicable Claim Type (1)

Claim Type:

Service Number:
3730

Damage
Code

HST

--

--

--

0039

Parts Manufacturer

Atlas, Atlas Cross Sport

Labor Operation 3): GFF functions (including Battery
Charge)

VOA (2)

01500010 = See Elsa for latest time units.

Labor Operation 3): Update Programming

See GFF Time expenditure

Causal Part: Select Labor Operation

01500060
Diagnostic Time (4)

GFF Time expenditure

01500060 = 50 TU max.

YES

Road Test

01210004 = 00 TU

NO

Technical Diagnosis

01320000 = 00 TU max.

NO

Claim Comment: Input “As per Technical Bulletin “2078469” in comment section of Warranty Claim.
1)

Vehicle may be outside any Warranty in which case this Technical Bulletin is informational only

2)

Code per warranty vendor code policy.

3)

Labor Time Units (TUs) are subject to change with ELSA updates.

4)

Documentation required per Warranty Policies and Procedures Manual.

Required Parts and Tools
No special parts required.

Tool Description

Tool No.
GRX3000VAS

Midtronics Battery Tester/Charger

or
MTRMSP0702 battery maintainer/charger

VAS Diagnostic Tool

VAS 6150/X & VAS 6160/X with:
ODIS Service with current online updates.

Additional Information
All part and service references provided in this Technical Bulletin are subject to change and/or removal.
Always check with your Parts Dept. and Repair Manuals for the latest information.
© 2025 Volkswagen Group of America, Inc. All rights reserved. Information contained in this document is
based on the latest information available at the time of printing and is subject to the copyright and other
intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors.
All rights are reserved to make changes at any time without notice. No part of this document may be
reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites,
without the prior expressed written permission of the publisher.

OWNER INFORMATION ABOUT CONTROL MODULE TUNING*
ACKNOWLEDGEMENT AND AUTHORIZATION FOR
REPROGRAMMING (REFLASHING) OF CONTROL MODULE(S)
*) “TUNING” is described as the addition of or modification of any component which causes a
Volkswagen vehicle to perform outside the normal parameters and specifications approved by
Volkswagen Group of America / Volkswagen Group Canada.

Date:
Dealer Number:
Vehicle Identification Number:
Repair Order Number:
Dealer stamp

I

, owner or driver of the above identified Volkswagen, confirm:

- “Tuning” as described above (especially power increasing modifications) has NOT been
performed on my vehicle.
- “Tuning” as described above has been performed on my vehicle and the following components
were modified or installed:

TUNING was performed by (Please provide Company name and telephone number, if you wish us
to contact them):

I understand that if my Control Module is determined to have been tuned, any damage caused by
the tuning of the Control Module (including adverse emissions consequences) will not be covered
by VWGoA / VGC warranties.
I am permitting an authorized Volkswagen Dealer to reflash (update) my Control Module, and by
doing so, I understand that this process will automatically overwrite (destroy) and permanently
delete any tuning program that was previously installed on the Control Module of my Volkswagen
vehicle.
By signing below, I fully acknowledge and understand that the tuning program will not be restored
and VWGoA / VGC, will not be liable in any way for the loss of tuning data.

Signature of Customer
E

2025 Volkswagen Group of America Inc.

All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright
intellectual property
rights of VGoA / VGCA Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or
other
and
by any means, .electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites, without the prior expressed written permission of the publisher.