NHTSA ID Number: 11016784
Manufacturer Communication Number: L-SB-0036-22 Rev2
TSB/Document Date: 2025-04-08
Summary
Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Global Techstream+ (GTS+) ECU flash reprogramming procedures and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard+ (CUW+). To ensure the correct ECU software is installed, ECUs will require a Security Signature before the ECU will initialize the flash reprogramming sequence. This bulletin also details the process for acquiring a Security Signature from TIS during the GTS+ ECU flash reprogramming process.
© 2025 Lexus, a division of Toyota
Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
Page 9 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
F. To review the Service Bulletin and access
the calibration file, click the Service Bulletin
link in the Document Title column of the
Calibration Search Result portlet.
Figure 8.
NOTE
ONLY Lexus certified technicians and other
authorized users may access
calibration files.
2. Connect the DCA-8000 battery diagnostic tool.
NOTE
Refer to Vehicle Reprogramming Tips for other approved chargers, located at
TIS – Diagnostics – Reprogramming – Reference Documents.
A. Connect the DCA-8000 battery diagnostic tool to the vehicle and turn it ON.
B. Select Power Supply Mode.
NOTICE
• ECU damage may occur if the correct battery charger and mode setting are NOT used.
• The battery diagnostic tool MUST be used in Power Supply Mode to maintain battery
voltage at 13.5V while flash reprogramming the vehicle.
• For details on how to use the battery diagnostic tool, refer to the
DCA-8000 Instruction Manual located at TIS – Diagnostics – Tools & Equipment –
Battery Diagnostics.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
Page 10 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
3. Click the appropriate calibration ID and reprogram the vehicle’s ECU with GTS+.
A. AFTER reviewing the procedures outlined in the selected Service Bulletin, click the
appropriate calibration ID link by matching the vehicle’s current calibration ID to the
Previous Calibration ID in the Calibration Identification Chart.
NOTE
• Calibration files are embedded as live links in the Service Bulletin.
• Some vehicles require special preparation. Review the selected Service Bulletin carefully.
Figure 9.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
Page 11 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
B. Click Open to load the calibration file information. If prompted to choose GTS or GTS+,
select GTS+.
NOTE
• GTS+ downloads calibration files as needed to ensure the latest calibration file is used.
• Do NOT save calibrations locally on the hard drive or other media for future use.
Figure 10.
Figure 11.
NOTICE
Errors during the flash reprogramming process can permanently damage the vehicle
ECU. Minimize the risk by following the steps below.
• Battery voltage MUST NOT FALL BELOW 12V during reprogramming. Confirm battery
voltage is higher than 12V but be sure voltage DOES NOT RISE ABOVE 16.0V
during reprogramming.
• Turn OFF ALL vehicle accessories (audio system, A/C, interior lights, DRL, etc.).
• Do NOT add to or significantly change the vehicle’s electrical load
while reprogramming.
• Confirm the hood is open and ensure under-hood temperature does NOT exceed
158°F (70°C ).
• Confirm cable connections between the vehicle and Techstream are secure.
• Do NOT disconnect or turn off Techstream or vehicle ignition during reprogramming.
• Set the parking brake.
• Complete ALL flash calibration updates provided for each ECU.
• If the battery’s State-Of-Charge (SOC) or capacity is in question, test with SST No.
DSS-5000P T (Battery Diagnostic Tool), and follow the DSS-5000 Instruction Manual
located at TIS – Diagnostics – Tools & Equipment – Battery Diagnostics.
• The DCA-8000 battery diagnostic tool MUST be used in Power Supply Mode to
maintain battery voltage at 13.5V while flash reprogramming the vehicle.
For details on how to use the DCA-8000 battery diagnostic tool, refer to the
DCA-8000 Instruction Manual located at TIS – Diagnostics – Tools & Equipment –
Battery Diagnostics.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
Page 12 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
C. Click Next to start the calibration
update process.
Figure 12.
D. Confirm the following:
• The PC is connected to VIM.
• The VIM is connected to DLC3 connector.
• The Ignition is ON and the engine is OFF or READY-OFF (hybrid vehicles).
Then, click Next.
Figure 13.
1
1
Select the Correct Device Tool (“MongoosePro MFC,” “MongoosePro MFC2,” or
“Mongoose-Plus MFC3” VIM)
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
E. Verify the correct current and NEW
calibration information, then click Next.
Figure 14.
NOTICE
• The total number of calibration IDs
in the calibration file corresponds to
the number of reprogrammable
processors in the ECU.
• The figure to the right shows an
example of the update procedure for
a two-processor ECU.
F. Turn the ignition OFF, click Next, and wait
at least 10 seconds before proceeding.
Figure 15.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
Page 13 of 20
L-SB-0036-22
Rev2
August 15, 2022
Page 14 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
G. Turn the Ignition ON (IG ON Ready-OFF
for hybrid vehicles).
Figure 16.
H. Confirm the following:
• The PC is connected to VIM.
• The hood is open.
• ALL accessories are OFF.
• Battery voltage is above 12V.
NOTICE
Verify the vehicle is connected to a
battery charger before continuing. If
battery voltage falls below 12V, ECU
damage may occur.
Then, click Start.
NOTE
If the key cycle is NOT done properly, reprogramming will fail, and an error message will appear
prompting you to restart.
I.
Based on the version of GTS+ being used, please follow the appropriate steps listed below:
• GTS+ software version 2024.03 or newer, go to sub step P.
• GTS+ software version 2024.02 or older, continue to sub step J.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
Page 15 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
J. This vehicle is equipped with additional security measures requiring a Signature from TIS.
Select Next to open TIS and retrieve the Signature.
Figure 17.
K. Input TIS login credentials and select Login.
Figure 18.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
L. Input TIS login credentials for secondary authentication and select Login.
Figure 19.
M. Select Send.
Figure 20.
N. Click Copy to Clipboard to copy the signature from TIS.
Figure 21.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
Page 16 of 20
L-SB-0036-22
Rev2
August 15, 2022
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
O. Paste the Signature into CUW+ and select Next.
Figure 22.
P. Select OK to continue.
Figure 23.
NOTE
Sub steps P and Q are ONLY required for
GTS+ software version 2024.03 and newer.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
Page 17 of 20
L-SB-0036-22
Rev2
August 15, 2022
Page 18 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
Q. Enter your password and select LOG IN
to continue
Figure 24.
R. Do NOT disturb the vehicle during
flash reprogramming.
Figure 25.
NOTE
• ECU flash reprogramming may take
3 – 30 minutes per calibration file.
• Reprogramming time will vary
depending on model and ECU
communication protocol. Vehicles using
CAN communication protocol will
reprogram much faster (2 – 7 minutes).
S. Does the vehicle require only ONE calibration update?
• YES — Go to sub step T.
• NO — If the vehicle requires a SECOND calibration update, continue as follows:
• For serial communication vehicles, continue to sub step T.
• For CAN communication vehicles, go to sub step V.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
L-SB-0036-22
Rev2
August 15, 2022
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
T. When Cal 1 completes the update
process, turn the ignition OFF, click Next,
and wait a MINIMUM of 10 seconds
before proceeding.
Figure 26.
U. Turn the ignition to the ON position,
then click Start.
Figure 27.
NOTE
If the key cycle is NOT done properly,
reprogramming may fail, and an error
message will appear prompting you to
restart Cal 2.
V. Do NOT disturb the vehicle during
flash reprogramming
Figure 28.
.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
Page 19 of 20
L-SB-0036-22
Rev2
August 15, 2022
Page 20 of 20
GTS+ ECU Flash Reprogramming With Security Signature
Operation Procedure (continued)
W. Turn the ignition OFF, click Next, and
wait a MINIMUM of 10 seconds
before proceeding.
Figure 29.
X. Turn the ignition to the ON position, then
click Next.
Figure 30.
Y. Confirm calibrations were updated and
click Finish.
Figure 31.
NOTE
On some models, DTCs may set as a result of reprogramming. If DTCs are present, clear codes and
run the Health Check again. Troubleshoot ANY remaining current, pending, or history codes.
Permanent codes will NOT be cleared using GTS+. Permanent codes do NOT illuminate the MIL and
do NOT require troubleshooting. They will clear during normal driving once the Universal Trip Drive
Pattern is performed.
© 2025 Lexus, a division of Toyota Motor Sales, USA
Submitted to NHTSA on 03/07/2025
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: L-SB-0036-22 Rev2
Replacement Service Bulletin Number:
MFR Communication Date: 2025-02-10
MFR Internal Campaign ID/Software Version: L-SB-0036-22 Rev2
Communication Type: Service Bulletin/Repair Instructions
NHTSA Components: ELECTRICAL SYSTEM
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU coding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Programming): Allows for Ford, for Lincoln, and for Mazda ECU programming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- Cost-effective ECU Coding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 3 Years Software Update, Value for Money: With 3 years of software updates and 22+ languages(no IP restrictions), XTOOL D7S auto scanner code scanner ensures ongoing compatibility for the latest car models and improved diagnostic functions. This all system vehicle diagnostic scanner comes with a 30-day return policy and a 24-month repair for dependable performance. XTOOL are dedicated to your satisfaction, so enjoy seamless support and lifetime expert assistance. Should you encounter any issues or concerns, don’t hesitate to reach out XTOOL. D7S with newest update with 22 languages freely transfer without authorization, check details from setting-language or from XTOOL
- 🔥 Historical lowest pr-ice now on sa-le--hot se-lling.
- 【🎈𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝟲 𝗲𝘀𝘀𝗲𝗻𝘁𝗶𝗮𝗹 𝗿𝗲𝘀𝗲𝘁 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗔𝗕𝗦 𝗕𝗹𝗲𝗲𝗱𝗶𝗻𝗴, 𝗢𝗶𝗹 𝗥𝗲𝘀𝗲𝘁, 𝗘𝗣𝗕, 𝗦𝗔𝗦, 𝗧𝗵𝗿𝗼𝘁𝘁𝗹𝗲 𝗥𝗲𝗹𝗲𝗮𝗿𝗻, 𝗮𝗻𝗱 𝗕𝗠𝗦—𝗽𝘂𝘁𝘁𝗶𝗻𝗴 𝗽𝗿𝗼𝗳𝗲𝘀𝘀𝗶𝗼𝗻𝗮𝗹-𝗴𝗿𝗮𝗱𝗲 𝗺𝗮𝗶𝗻𝘁𝗲𝗻𝗮𝗻𝗰𝗲 𝗯𝗮𝗰𝗸 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗵𝗮𝗻𝗱𝘀.】Spongy brakes? Stuck oil light? Parking brake won't release? Off-center steering? Rough idle after battery disconnect? Draining battery? IF745 handles all with a few taps. One tool covers six dealer-level resets, saving hundreds in labor costs. ❗ NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨ 𝗜𝗙𝟳𝟰𝟱 𝗴𝗼𝗲𝘀 𝗯𝗲𝘆𝗼𝗻𝗱 𝗯𝗮𝘀𝗶𝗰 𝗰𝗼𝗱𝗲 𝗿𝗲𝗮𝗱𝗶𝗻𝗴 𝘄𝗶𝘁𝗵 𝟭𝟬 𝗶𝗻𝘁𝗲𝗴𝗿𝗮𝘁𝗲𝗱 𝗳𝘂𝗻𝗰𝘁𝗶𝗼𝗻𝘀—𝗗𝗧𝗖 𝗟𝗼𝗼𝗸𝘂𝗽, 𝗜/𝗠 𝗥𝗲𝗮𝗱𝗶𝗻𝗲𝘀𝘀, 𝗙𝗿𝗲𝗲𝘇𝗲 𝗙𝗿𝗮𝗺𝗲, 𝗟𝗶𝘃𝗲 𝗗𝗮𝘁𝗮, 𝗢𝟮𝗦, 𝗢𝗕𝗠, 𝗘𝗩𝗔𝗣, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Pulling a code tells you something is wrong. IF745 tells you what the code means, when the fault happened, and what data surrounds it. Pass emissions with one I/M Readiness tap. Freeze the fault moment with Freeze Frame. Monitor live sensor data in real time. Turn cryptic codes into clear answers.
- 【🛒 𝗜𝗙𝟳𝟰𝟱 𝗽𝗲𝗿𝗳𝗼𝗿𝗺𝘀 𝗳𝘂𝗹𝗹-𝘀𝘆𝘀𝘁𝗲𝗺 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀 𝗮𝗰𝗿𝗼𝘀𝘀 𝗮𝗹𝗹 𝗺𝗼𝗱𝘂𝗹𝗲𝘀—𝗲𝗻𝗴𝗶𝗻𝗲, 𝗔𝗕𝗦, 𝗮𝗶𝗿𝗯𝗮𝗴, 𝘁𝗿𝗮𝗻𝘀𝗺𝗶𝘀𝘀𝗶𝗼𝗻, 𝘀𝘁𝗲𝗲𝗿𝗶𝗻𝗴, 𝘀𝘂𝘀𝗽𝗲𝗻𝘀𝗶𝗼𝗻, 𝗯𝗼𝗱𝘆 𝗲𝗹𝗲𝗰𝘁𝗿𝗼𝗻𝗶𝗰𝘀, 𝗮𝗻𝗱 𝗺𝗼𝗿𝗲. 】Warning lights on but you don't know why? Skip the $100+ diagnostic fee at the shop. Run a complete self-check from your driveway. IF745 reads and clears fault codes, retrieves ECU info, and displays live data from every accessible module—delivering a full vehicle health report in minutes, without leaving home.
- 【✅𝗜𝗙𝟳𝟰𝟱 𝗳𝗲𝗮𝘁𝘂𝗿𝗲𝘀 𝗮 𝟳-𝗶𝗻𝗰𝗵 𝗱𝗶𝘀𝗽𝗹𝗮𝘆, 𝗲𝗿𝗴𝗼𝗻𝗼𝗺𝗶𝗰 𝗱𝗲𝘀𝗶𝗴𝗻, 𝗪𝗶-𝗙𝗶 𝘂𝗽𝗱𝗮𝘁𝗲𝘀, 𝗮𝗻𝗱 𝘇𝗲𝗿𝗼 𝘀𝘂𝗯𝘀𝗰𝗿𝗶𝗽𝘁𝗶𝗼𝗻 𝗳𝗲𝗲𝘀 𝗳𝗼𝗿 𝗵𝗮𝘀𝘀𝗹𝗲-𝗳𝗿𝗲𝗲 𝗱𝗶𝗮𝗴𝗻𝗼𝘀𝘁𝗶𝗰𝘀.】Large screen means no squinting. Intuitive navigation and customizable data displays put key info at your fingertips. Wi-Fi delivers lifetime free updates without a computer. No recurring fees. No hidden costs. Just a reliable tool that works as hard as you do.
This product presentation was made with AAWP plugin.