INDIAN MOTORCYCLE

HELP CENTER
What can we help you find?

Search

Help Center Home / Article

02/14/2025

2016+ Indian Springfield Drive Belt Inspection and Tension
Adjustment
Indian Springfield Drive Belt Inspection and Tension Adjustment - Indian Motor…
Motor…

Required Tools and Supplies
Shop Rags
27mm Crowfoot Wrench
Tape Measure
Marking Tool
Belt Tension or 10-Pound Weight
6mm Allen Socket
13mm Socket
Torque Wrench
Motorcycle Lift

Ratchet
27mm Wrench
Safety Glasses and Nitrile Gloves

To learn more about tools, read the Tools and Fasteners Guide.
Always wear safety glasses and nitrile gloves when servicing your Indian Motorcycle. To inspect and
adjust the drive belt tension on your Indian Springfield, follow these steps:

1. Park the bike on a flat, level surface and allow it to cool completely.
2. On each side, pull the upper side cover out evenly to disengage each tab from the frame.
Disconnect the saddlebag lock connector near the seat.
Open the saddlebag and remove the two saddlebag fasteners with a 6mm Allen socket.
Tilt the saddlebag out and lift up to remove.

3. Ensure the motorcycle is in NEUTRAL.
4. Safely elevate the rear wheel. The motorcycle must be stable before proceeding.
5. Inspect the drive belt for wear or damage. Refer to your Owner’s Manual for belt wear analysis.
See your authorized Indian Motorcycle Dealer if replacement is needed.
6. Applying 10 pounds of force, check and record the belt deflection. Ensure the belt is dry before
measuring. Locking the tape measure will help maintain consistent measurements.
Using the tire valve stem as a reference, measure at three additional points 90 degrees apart. The drive belt deflection at 10
pounds of force should be 34mm (1.3 inches) or 11 notches up the belt guard.
If adjustment is needed, rotate the wheel forward and mark the tightest measurement point on the tire for reference.

7. Also mark the current adjuster locations on both sides of the rear wheel for reference.
8. Place a rag against the exhaust to prevent scratching the paint. Loosen but do not remove the
axle nut with a 27mm wrench.
9. Retighten the nut with a 27mm crowfoot wrench to the adjustment specification of 15 ft-lbs (20
Nm).
10. Turn the right-side adjuster nut with a 13mm socket to achieve proper belt tension.
11. When the belt tension is correct, move to the left side to adjust the final belt alignment.
12. To minimize change in belt tension, use only the left-side adjuster to make final adjustments to
belt alignment. Be sure to keep the axle seated forward against the axle adjusters during this
procedure.
13. While rotating the wheel backward, tighten the left-side adjuster nut until the drive belt is
centered in the driven pulley. Sprocket teeth should be visible on both sides of the belt.
14. Once the desired setting is achieved, rotate the wheel forward and verify the sprocket teeth are
still visible on both sides of the belt.

15. If necessary, revert back to the initial settings and repeat this process as needed.
16. Re-check drive belt tension to verify it is still within specification. Improper tension or alignment
can cause driveline noise and damage the drive belt.
17. Once complete, tighten the rear axle nut to the final specification of 65 ft-lbs (88 Nm).
18. Pump the rear brake pedal several times to reset brake pad distance.
19. Then verify the wheel rotates smoothly and freely without drag when the brake pedal is
released.
20. Safely lower your motorcycle to the ground. Refer to your Owner’s Manual for helpful hints and
techniques.
21. Begin reinstalling the saddlebags by placing them on the muffler brackets.
22. Reinstall the saddlebag fasteners. Torque to 18 ft-lbs (24 Nm).
23. Reconnect the electrical wiring, if necessary, and ensure the saddlebags are mounted properly.
24. Align the three side panel grommets and reinstall each upper side panel.
For more information, see your authorized Indian Motorcycle Dealer. Find a dealer near you with
the Dealer Locator.
Maintenance tips, procedures and specifications can be found in your Owner's Manual.
To find diagrams and replacement part numbers, use the online parts catalog.
YouTube® is a registered trademark of Google LLC
Unless noted, trademarks are the property of Polaris Industries Inc.
© 2022 Polaris Industries Inc.
Was this article helpful?
Yes, it answers my question
No, it's missing information or visuals
No, the instructions are unclear
No, What are the next steps?