Classification:

Reference:

BT24-007A

Date:

NTB25-006A

February 17, 2025

LEFT AND/OR RIGHT REAR DOOR REAR SASH COVER IS
LOOSE OR MISSING
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES:

2025 Kicks (P16)

IF YOU CONFIRM
Either the left and/or the right Rear Door Rear Sash Cover is loose or missing.
HINT: A loose Rear Door Rear Sash Cover can be lifted at the top/forward corner shown in
Figure 1 with one (1) finger and only a few pounds of effort. The driver (LH) side is shown
in Figure 1. The passenger (RH) side is similar.

Lift here
Rear Door Rear
Sash Cover

Figure 1
ACTION
Replace the affected Rear Door Rear Sash Cover with part listed in the PARTS
INFORMATION.
IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/11

REQUIRED SPECIAL TOOL

New or replacement Essential Tools are available from Tech•Mate online:
www.techmatetools.com, or by phone: 1-833-397-3493.


Manual Applicator (NI-50816A), or equivalent.

Figure 2

2/11

NTB25-006A

SERVICE PROCEDURE

HINT: The following Figures will be of the driver (LH) side Rear Door Rear Sash Cover.
The passenger (RH) side Rear Door Rear Sash Cover is similar.

1.

If still present, remove the affected
Rear Door Rear Sash Cover.


Use an appropriate tool (Figure 4)
to remove Rear Door Rear Sash
Cover.

Rear Door Rear
Sash Cover

Figure 3

Rear Door Rear
Sash Cover

Appropriate tool

Figure 4

3/11

NTB25-006A

2.

Remove all residual adhesive tape (Figure 5) from the vehicle, as shown in Figure 6.


Use 91% isopropyl alcohol to remove all adhesive tape.

IMPORTANT: All adhesive tape and associated residue MUST be removed.

Residual
adhesive tape

Figure 6

Figure 5

3.

Remove the clip from the new Rear
Door Rear Sash Cover, and then
install the clip into the door where
shown in Figure 7.


Sash molding
endcap

See PARTS INFORMATION.

Rear Door Rear
Sash Cover clip
Figure 7

4/11

NTB25-006A

4.

In preparation to install the new Rear Door Rear Sash Cover, clean the areas shown
in Figure 8 with 91% isopropyl alcohol and confirm that all dirt, debris and finger prints
have been removed.


Confirm that ALL isopropyl alcohol has dried before moving to next step.

Figure 8

5/11

NTB25-006A

IMPORTANT: The preparation of all parts and equipment must happen before mixing the
adhesive in the applicator Mixing Nozzle.
5.

Assemble the Manual Applicator (NI-50816A), Adhesive Single Tube and a Mixing
Nozzle (Figure 9 and Figure 10).
a. Remove and discard the red plug from the Adhesive Single Tube (P/N 999MP3M08237) by unlocking the retaining collar.
b. Attach the Mixing Nozzle by sliding the retaining collar over the Mixing Nozzle and
locking the retaining collar onto the Adhesive Single Tube.
c. Place the Adhesive Single Tube with the Mixing Nozzle attached into the Manual
Applicator (NI-50816A).
HINT: DO NOT squeeze the Manual Applicator handle yet.
Red plug

Adhesive Single Tube

Retaining collar
Mixing Nozzle
Figure 9
Manual Applicator
(NI-50816A)

Figure 10
6/11

NTB25-006A

IMPORTANT: In the next steps the Rear Door Rear Sash Cover MUST be aligned and
completely installed before the adhesive starts to harden.



6.

Please read steps 6-13 before applying adhesive.
Adhesive will start hardening approximately 1 minute after it exits the Mixing
Nozzle. After 3 minutes it will harden.
Mixing Nozzle will begin to clog in 2-3 minutes after mixing has stopped.

Apply a small amount of the adhesive to a scrap piece of cardboard until it appears
that the adhesive exits the Mixing Nozzle and is evenly mixed (Figure 11).

Figure 11
7.

Apply a 6 mm wide, 30 mm long bead of Adhesive Single Tube to the area of the
Rear Door Rear Sash Cover where shown in Figure 12.


8.

IMPORTANT: The Rear Door Rear Sash Cover must be installed immediately
after adhesive is applied. Adhesive will start hardening approximately 1 minute
after it exits the Mixing Nozzle. After 3 minutes it will harden.

Remove three (3) red protective adhesive tape strips from new Rear Door Rear Sash
Cover.

6 mm wide bead of
adhesive

Red protective adhesive
tape strips (3)
30 mm long
Figure 12
7/11

NTB25-006A

9.

Align the lower Rear Door Rear Sash Cover tab and lower clip to the vehicle door as
shown in Figure 13.

Rear Door Rear
Sash Cover

Rear Door Rear Sash
Cover lower clip
Lower Rear Door Rear Sash
Cover tab

Figure 13

10.

Align the upper Rear Door Rear Sash Cover tab to the sash molding endcap.

Sash molding
endcap

Upper Rear Door
Rear Sash Cover tab

Rear Door Rear
Sash Cover

Figure 14

8/11

NTB25-006A

11.

Push the Rear Door Rear Sash Cover clip at the bottom to snap it in place.

12.

Push the Rear Door Rear Sash Cover upper clip to snap it in place.

13.

Apply consistent, even pressure to the Rear Door Rear Sash Cover for at least 30
seconds.


Using both hands, as shown in Figure 15, apply pressure by leaning at a slight
angle in relation to the vehicle.

Figure 15

9/11

NTB25-006A

14.

Confirm that the double-sided tape
has adhered properly by gently trying
to lift the leading edge of the Rear
Door Rear Sash Cover at the three (3)
points shown in Figure 16, Figure 17
and Figure 18.


Top of Rear Door
Rear Sash Cover

The leading edge of the Rear Door
Rear Sash Cover should not lift.
Figure 16

15.

Allow the vehicle to sit undisturbed for
1 hour, after the repair has been
completed.

16.

Using the same method as in step 14,
re-confirm that the double-sided tape
has adhered properly.


If excessive movement is observed
please contact your local FQM
(Field Quality Manager) for further
direction.

Middle of Rear Door
Rear Sash Cover
Figure 17

IMPORTANT: Once the repair is completed,
do not wash the vehicle. It is recommended
that the vehicle should avoid excess sun
(heat) and water exposure as much as
reasonably possible for up to 24 hours as
the tape and adhesive cures.

Bottom of Rear Door
Rear Sash Cover

Figure 18

10/11

NTB25-006A

PARTS INFORMATION

(1)
(2)

(3)

DESCRIPTION

PART NUMBER

Rear Door Rear Sash Cover RH

(1)

Rear Door Rear Sash Cover LH

(1)

Adhesive Single Tube (2)

999MP-3M08237

Nozzles Bag of six (2)

999MP-3M08193

QUANTITY
1
If needed
1
If needed
As needed
(3)
As needed

Look up the part number in the Electronic Parts Catalog by vehicle VIN.
Order this item through the Nissan Maintenance Advantage program: Phone 877-NISNMA1 (877-647-6621). Website order via link on the dealer portal; www.NNAnet.com
and click on the “Maintenance Advantage-Tire/Battery/Chemical” link.
Use a new nozzle for each side of the vehicle. 1 (one) nozzle will attach 1 (one) Rear
Door Rear Sash Cover; a total of 2 (two) per vehicle.

CLAIMS INFORMATION
Submit a Primary Part (PP) type line claim using the following claims coding:
DESCRIPTION

PFP

Inspect Both Rear Door Sash Covers
Inspect Both Rear Door Sash Covers &
Replace One
Inspect and Replace Both Rear Door
Sash Covers
(1)

OP CODE

SYM

DIA

FRT

SX35AA
(1)

SX36AA

0.2
ZA

0.4

32

SX37AA

0.7

Reference the electronic parts catalog and use the Rear Door Rear Sash Cover as
the Primary Failed Part (PFP).

Expense Code:
EXPENSE CODE

DESCRIPTION

MAX AMOUNT

068

Adhesive Single Tube (1)

$8.01

069

Nozzles Bag of six (2)

$2.94

(1)
(2)

One 6.75 oz. cartridge of “Adhesive Single Tube” (P/N 999MP-3M08237) will cover
twelve (12) vehicles.
Two Nozzles from “Nozzles Bag of six” (P/N 999MP-3M08193) will cover one (1)
vehicle.

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
January 17, 2025

NTB25-006

February 17, 2025

NTB25-006A

DESCRIPTION
Original bulletin published
PARTS INFORMATION and Expense Code
updated

11/11

NTB25-006A