Classification:

Reference:

BR24-002A

Date:

NTB24-050A

January 10, 2025

FALSE ACTIVATION OF AEB OR FCW
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES:

2022-2023 Kicks (P15)

APPLIED DATES:

Built on or before August 3, 2024

APPLIED SYSTEMS:

Automatic Emergency Braking/Forward Collision Warning

IF YOU CONFIRM
The customer states they have experienced false activation and/or unexpected braking of
the Automatic Emergency Braking (AEB) or Forward Collision Warning (FCW) system with
a red/white flashing message in meter and a loud noise,

AND
There are no related DTCs stored.

ACTION
1.

Confirm the current ICC/ADAS 2 part number.

2.

Reprogram the ICC/ADAS 2, if applicable.

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/22

SERVICE PROCEDURE
Reprogram the ICC/ADAS 2
IMPORTANT: Before starting, make sure:

1.



ASIST on the CONSULT PC has been synchronized (updated) to the current date.



All CONSULT-III plus (C-III plus) software updates (if any) have been installed.



During the reprogramming process, you may receive some errors. These errors
are expected. Please follow all of the steps in this procedure to successfully
complete the reprogramming process.



Connect a battery maintainer or smart charger set to reflash mode or a similar
setting. If the vehicle battery voltage drops below 12.0V or rises above 13.5V
during reprogramming, the ICC/ADAS 2 control module may be damaged.



Be sure to turn OFF all vehicle electrical loads. If a vehicle electrical load remains
ON, the ICC/ADAS 2 control module may be damaged.



Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops
during reprogramming, the process will be interrupted and the ICC/ADAS 2 control
module may be damaged.



Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within
range of the CONSULT PC and the VI. If Bluetooth® signal waves are within range
of the CONSULT PC or VI during reprogramming, reprogramming may be
interrupted and the ICC/ADAS 2 control module may be damaged.

Connect the Vehicle Interface (VI) to the vehicle.


Make sure to use the correct VI for the CONSULT PC.

2.

Turn the ignition ON with the engine OFF.

3.

Turn ON the hazard warning lamps.

4.

Start C-III plus.

5.

If prompted, select USA/CANADA Dealers from the drop down menu, and then
select OK.

6.

Login using your NNAnet credentials.
IMPORTANT: If not prompted to enter your username and password, the CONSULT
PC may not be connected to Wi-Fi. Close C-III plus, confirm the CONSULT PC is
connected to Wi-Fi, and then reopen C-III plus.

2/22

NTB24-050A

7.

Wait for the VI to be recognized.


8.

The serial number will display when the VI is recognized (Figure 1).

Select Re/programming, Configuration.

Figure 1

3/22

NTB24-050A

9.

Check the box to confirm the precaution instructions have been read, and then select
Next.
HINT: Use the arrows (if needed) to view and read all precautions.

Figure 2

10.

Select Automatic Selection(VIN).

Example

Figure 3

4/22

NTB24-050A

11.

Confirm the VIN or Chassis # is correct, and then select Confirm.

XXXXXXXXXXXXXXX
KICKS
XXXXMY

Figure 4

12.

Confirm the VIN is correct for the vehicle, and then select Confirm.

XXXXXXXXXXXXXXXXX

Figure 5

5/22

NTB24-050A

13.

Select ICC/ADAS 2.

Figure 6

14.

Select Reprogramming.

Figure 7

6/22

NTB24-050A

15.

Find the ICC/ADAS 2 Part Number and write it on the repair order, and then select
Save.
HINT: This is the current Part Number (P/N).

XXXXXXXXXXXX

ICC/ADAS 2

XXXXXXXXXX
KICKS

XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX

Figure 8

16.

Compare the Part Number you wrote down in step 15 to the numbers in the
CURRENT ICC/ADAS 2 PART NUMBER column in Table A.


If there is a match in Table A, continue with the reprogramming procedure.



If there is not a match, in Table A, this bulletin does not apply. See the ESM
(Electronic Service Manual) for further diagnostic information.

Table A
MODEL

CURRENT ICC/ADAS 2 PART NUMBER: 284E7-

Kicks

5R00A, 5R01A

7/22

NTB24-050A

17.

Check the box to confirm the precaution instructions have been read, and then select
Next.
HINT: Use the arrows (if needed) to view and read all precautions.

Figure 9

8/22

NTB24-050A

18.

Make sure OK is highlighted green (battery voltage must be between 12.0 and 13.5
volts).
To avoid damage to the control unit, ensure a battery maintainer or smart charger is
connected. The battery voltage must be between 12.0V and 13.5V during
reprogramming.

19.

Select Next.

Figure 10

9/22

NTB24-050A

20.

Confirm the Judgement for all the Monitor Items are “OK”, and then select Start.

13.1

EXAMPLE

Figure 11

21.

Allow Transfer Data to complete.

Figure 12

10/22

NTB24-050A

22.

Once the reprogramming completes, select Next.
HINT:
o If the screen in Figure 13 does not display (indicating that reprogramming did
not complete), refer to the information on page 12.
o Additional steps/operations are required before CONSULT will provide the final
reprogramming confirmation report. Continue with the reprogramming
procedure on page 13.

Figure 13

11/22

NTB24-050A

ICC/ADAS 2 Control Module Recovery

Do not disconnect the VI or shut down CONSULT if reprogramming does not
complete.

If reprogramming does not complete and the “!?” icon displays, as shown in
Figure 14:


Check battery voltage
(12.0 - 13.5 V).



Ignition is ON, engine OFF.