Service

Technical Information

11/24

Programming sequence:

ENU

APB6

0

Read and follow the information and
instructions on the PIWIS Tester during the
guided programming sequence.
Do not interrupt the programming and
coding process.
A backup documentation process for the
re-programmed software releases starts as
soon as programming and coding is complete.

Programming time (approx.):

10 minutes

Software release programmed during
this campaign:

•
•

Porsche Mobile Charger: 0142
Porsche Mobile Charger Plus: 3000

When programming is complete, the software
release can be read out of the charger (Porsche
Mobile Charger) in the “Extended identifications”
menu using the PIWIS Tester.
Procedure in the event of a termination
in the control unit programming:

Repeat programming by entering the
programming code again.

Procedure in the event of error
messages appearing during the
programming sequence:

 Workshop Manual '9X00IN Basic instructions
and procedure for control unit programming
using the PIWIS Tester – section on “Troubleshooting”'.

1.7

Remove the VAS diagnostic tool from the charger (Porsche Mobile Charger).

1.8

Disconnect the supply cable from the power supply and remove it from the diagnostic
adapter.

2

Include the charger (Porsche Mobile Charger) with the vehicle or give it to the customer.

3

Enter the campaign in the Warranty and Maintenance logbook.

Continue with invoicing, scope 3 – 12.  Technical Information '9X00IN Warranty processing'

Re-programming Porsche Mobile Charger (Powerboard and Communication Board) - Connect
Action:

1

Re-program the power board.

AfterSales

Nov 25, 2024
Page 7 of 20

0

Service
APB6

ENU

Technical Information

11/24

1.1

Fasten supply cable  Connecting diagnostic
adapter -1- to the diagnostic adapter
for high-voltage charging system
Connecting diagnostic adapter -2- and
connect this to charger (Porsche Mobile
Charger Connect)  Connecting diagnostic
adapter -3-.

1.2

Connect the supply cable to the power
supply.

Connecting diagnostic adapter
1.3

Wait at least 3 minutes before connecting
P90999 - P90999 - PIWIS Tester 4 to the
vehicle communication module (VCI) via the
USB cable and connect the communication
module  Connecting communication
module (VCI) -1- to the diagnostic adapter
for high-voltage charging system
Connecting communication module (VCI) -2-.

1.4

On the PIWIS Tester start screen, call up the
‘Diagnostics’ application.
The vehicle type is then read out, the diagnostic application is started and the control
unit selection screen is populated.

Connecting communication module (VCI)

1.5

On the ‘manual model line selection’ screen, select the ‘External components’ model
line and confirm with ‘Next’.

1.6

Re-program the power board.
The basic procedure for control unit programming is described in the Workshop Manual 
Workshop Manual '9X00IN Basic instructions and procedure for control unit programming
using the PIWIS Tester'.
For specific information on programming the power board during this campaign,
see the table below:

Nov 25, 2024
Page 8 of 20

Required PIWIS Tester software
release:

42.950.010 (or higher)

Type of control unit programming:

Carry out control unit programming using the
‘Automatic programming’ function in the
Universal charging cable control unit.

AfterSales

Service

Technical Information

11/24

Programming sequence:

ENU

APB6

0

Read and follow the information and
instructions on the PIWIS Tester during the
guided programming sequence.
Do not interrupt the programming and
coding process.
A backup documentation process for the
re-programmed software releases starts as
soon as programming and coding is complete.

Programming time (approx.):

10 minutes

Software release programmed during
this campaign:

•

Procedure in the event of a termination
in the control unit programming:

Repeat programming by entering the
programming code again.

Procedure in the event of error
messages appearing during the
programming sequence:

 Workshop Manual '9X00IN Basic instructions

4501

When programming is complete, the software
release can be read out of the charger (Porsche
Mobile Charger Connect) in the “Extended
identifications” menu using the PIWIS Tester.

and procedure for control unit programming
using the PIWIS Tester – section on “Troubleshooting”'.

1.7

Remove the VAS diagnostic tool from the charger (Porsche Mobile Charger).

1.8

Disconnect the supply cable from the power supply and remove it from the diagnostic
adapter.

Information
A connection to a WiFi network is required for the communication board update.
If it is not possible to establish an Internet connection to the charger (Porsche Mobile Charger
Connect), the update can also be downloaded manually via the web address under E-Performance at
https://www.porsche.com and installed using the web application. This procedure is described further in
the instructions for the web application.

AfterSales

Nov 25, 2024
Page 9 of 20

0

Service
APB6

ENU

2

Technical Information

11/24

Re-program the communication board.
2.1

Secure the supply cable to the charger
(Porsche Mobile Charger) and connect it to
the power supply.

2.2

Wait for at least 30 seconds for the charger to
start.

2.3

Select the ‘Settings’ icon in the menu bar to
open the main menu  Opening Settings -1-.

Opening Settings
2.4

Select the ‘Networks’ function in the main
menu  Selecting Networks function -1-.

2.5

Activate WiFi  Connecting WiFi network -1and then select “WiFi networks” in order to
select the relevant network from the list of
detected WiFi networks  Connecting WiFi
network -2-.

2.6

Enter the WiFi password and confirm it.

Selecting Networks function

Nov 25, 2024
Page 10 of 20

AfterSales

Service

Technical Information
2.7

11/24

ENU

APB6

0

Return to the selection screen using the
arrow key and select the ‘Software updates’
function.

Connecting WiFi network
2.8

Deactivate automatic software updates 
Installing software update -1- and select the
‘Download’ function  Installing software
update -2-.

2.9

Once the latest software has been downloaded successfully, select the ‘Install’
function in order to confirm the message
Software update available.
The update can take up to 5 minutes.

2.10

Once the update is complete, confirmation
of the software update that was performed is
displayed. Confirm with ‘OK’.
Software release programmed during
this sequence
•

Communication board: 3030

Installing software update
Following the update, the software release is
displayed at the bottom of the screen in the ‘Software updates’ menu.
2.11
3

Switch off the charger (Porsche Mobile Charger Connect)

Include the charger (Porsche Mobile Charger Connect) with the vehicle or give it to the customer.

AfterSales

Nov 25, 2024
Page 11 of 20

0

Service
APB6

ENU

Technical Information

11/24

Information
Please perform the following to ensure proper functionality of the new cable and software after
performing the updates: - with the updated charger and the new/replacement APB6 Charger Power
Supply Cable, perform 3-5 boot-up cycles by plugging/unplugging charger from the wall, and
monitor the status LED's. - with the updated charger and the new/replacement APB6 Charger Power
Supply Cable, plugged into the wall, stress/manipulate/twist the cable while monitoring the status
LED's. - with the updated charger and the new/replacement APB6 Charger Power Supply Cable,
plugged into the wall and plugged into the vehicle, set at 100% charging rate (not 50%), charge the
vehicle for at least 1 hour.
If the status LED's do not indicate any issues, there are no charger faults or vehicle faults, the vehicle
charges successfully, and the vehicle is operating as designed, it can be released to the customer.
If the status LED's do indicate an issue, please provide a video recording of the flashing lights, a
screen shot of the charger fault memory, and a current VAL in a PRMS technical support ticket.
4

Enter the campaign in the Warranty and Maintenance logbook.

Continue with invoicing, scope 20 – 24.  Technical Information '9X00IN Warranty processing'

Warranty processing
Information
The specified working times were determined specifically for carrying out this campaign and include all
necessary preliminary and subsequent work.
The working times may differ from the working times published in the Labor Operation List in PCSS.
In cases where a customer returns with a complaint due to their newly received hardware or otherwise in
relation to their home charging installation, an exception to the standard process for claiming of consequential damage after the vehicle has left the PC will be allowed. In these exceptional cases the PC should
troubleshoot accordingly, and file a PRMS technical support or warranty / campaigns support ticket if
necessary. The subsequent credit must be submitted within a 4-week period from the customer pick up
date on the RO where the APB6 was performed.
Scope 1:

Removing Porsche Mobile Charger industrial (250V) supply cable from vehicle
Labor time:
Removing Porsche Mobile Charger industrial (250V) supply cable from
vehicle
 Damage Number APB6 099 000 1

Scope 2:

Nov 25, 2024
Page 12 of 20

Not valid.

AfterSales

Labor time: 10 TU

Service

Technical Information
Scope 3:

11/24

APB6

ENU

0

Replacing industrial (250V) supply cable and performing charger (Porsche Mobile Charger) software
update
•

Valid for Porsche Mobile Charger Basic
Labor time:
Replacing industrial (250V) supply cable and performing charger (Porsche
Mobile Charger) software update
Includes:
Connecting and disconnecting PIWIS Tester
Connecting and disconnecting diagnostic adapter for
high-voltage charging system

Labor time: 54 TU

Part required
V04015005BA
(or V04015001MH)

Supply cable (NEMA 6-30)

1 piece

 Damage Number APB6 099 000 2
Scope 4:

Replacing industrial (250V) supply cable and performing charger (Porsche Mobile Charger) software
update
•

Valid for Porsche Mobile Charger Basic
Labor time:
Replacing industrial (250V) supply cable and performing charger (Porsche
Mobile Charger) software update
Includes:
Connecting and disconnecting PIWIS Tester
Connecting and disconnecting diagnostic adapter for
high-voltage charging system

Labor time: 54 TU

Part required
V04015005BB
(or V04015001MJ)

Supply cable (NEMA 14-30)

1 piece

 Damage Number APB6 099 000 2
Scope 5:

Replacing industrial (250V) supply cable and performing charger (Porsche Mobile Charger) software
update
•

Valid for Porsche Mobile Charger Basic

AfterSales

Nov 25, 2024
Page 13 of 20

0

Service
APB6

ENU

Technical Information