ATTENTION:
GENERAL MANAGER

q

PARTS MANAGER

q

CLAIMS PERSONNEL

q

IMPORTANT - All
Service Personnel
Should Read and
Initial in the boxes
provided, right.

SERVICE MANAGER

q

© 2024 Subaru of America, Inc. All rights reserved.

SERVICE BULLETIN
APPLICABILITY:

2022-24MY BRZ

SUBJECT:

DTCs P2404, P0016-19, P0021,
& U0100 Diagnostic Procedures

NUMBER: 09-128-24R
DATE: 10/08/24
REVISED: 11/14/24

INTRODUCTION:
This bulletin announces availability of new reprograming files for the Engine Control Module (ECM)
developed to remedy the following DTCs:
•

P0016: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor A

•

P0017: Crankshaft Position - Camshaft Position Correlation Bank 1 Sensor B

•

P0018: Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor A

•

P0019: Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor B

•

P2404: Evap System Leak Detection Pump Sense Circuit Range/Performance

•

P0011: “A” Camshaft Position - Timing Over-Advanced or System Performance Bank 1

•

P0012: “A” Camshaft Position - Timing Over-Advanced or System Performance Bank 2

•

U0100: Lost Communication with ECM/PCM “A”

These new files contain the following enhancements:

•

Enhanced logic for the self-diagnosis program of the ECM and to optimize stabilization of
fuel pressure.

•

Optimized fuel trim providing stabilized engine combustion during Exhaust Gas Recirculation
(EGR) valve operation.

•

Enhanced logic to prevent the ELCM pump from seizing.

•

Self-shutdown logic for the starter motor relay program, eliminating the possibility frozen
relay contacts.

CAUTION: VEHICLE SERVICING PERFORMED BY UNTRAINED PERSONS COULD
RESULT IN SERIOUS INJURY TO THOSE PERSONS OR TO OTHERS.
Subaru Service Bulletins are intended for use by professional technicians ONLY. They
are written to inform those technicians of conditions that may occur in some vehicles,
or to provide information that could assist in the proper servicing of the vehicle. Properly
trained technicians have the equipment, tools, safety instructions, and know-how to
do the job correctly and safely. If a condition is described, DO NOT assume that this
Service Bulletin applies to your vehicle, or that your vehicle will have that condition.

Subaru of America, Inc. is
ISO 14001 Compliant
ISO 14001 is the international standard for
excellence in Environmental Management
Systems. Please recycle or dispose of
automotive products in a manner that is friendly
to our environment and in accordance with all
local, state and federal laws and regulations.

Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 1 of 15

PFC FILE INFORMATION:
Model

Model Year

Transmission

File Description

Old Part Number

New CID/ROMID

AT

22765AR283.pfc

22765AR280
22765AR281
22765AR282

ZF2L500D00G

MT

22765AR293.pfc

22765AR290
22765AR291
22765AR292

ZF2L500C00G

AT

22765AT543.pfc

22765AT540
22765AT541
22765AT542

ZF2M500D00G

MT

22765AT553.pfc

22765AT550
22765AT551
22765AT552

ZF2M500C00G

AT

22765AU492.pfc

22765AU490
22765AU491

ZF2P300D00G

MT

22765AU502.pfc

22765AU500
22765AU501

ZF2P300C00G

2022MY

BRZ
2023MY

2024

The files listed above can be found on SSM5-R
SERVICE PROCEDURE INFORMATION:
Perform a DTC scan. Refer to the table below for the next course of action.
DTC

Course of Action

P0016-19

Proceed to SECTION A

P2404

Proceed to SECTION B

U0100

Proceed to SECTION C

P0011-12

Connect the vehicle to a recommended power supply. See APPENDIX A for additional information regarding
power supply. Reprogram the ECM following the normal SSM5-R procedure. Detailed information regarding
the SSM5-R reprograming procedures can be found in TSB 14-28-21R.

SECTION A - DTC P0016-19 SERVICE PROCEDURE INFORMATION:
(*1) IMPORTANT: Use the following instructions to perform and read the OBD MODE test results.
This procedure will be required when performing the diagnostic steps outlined below.

Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 2 of 15

Read the following data monitor values:
1. MID - $35 TID - $8B
2. MID - $35 TID - $8C
3. MID - $35 TID - $8D
4. MID - $35 TID - $8E
5. MID - $36 TID - $8B
6. MID - $36 TID - $8C
7. MID - $36 TID - $8D
8. MID - $36 TID - $8E

STEP 1: Confirm DTCs P0016, P0017, P0018, or P0019 displayed in the ECM fault memory.
STEP 2: Review the battery charging information supplied in APPENDIX A. Reprogram the ECM following the
normal SSM5-R procedure. Detailed information regarding the SSM5-R reprograming procedures can
be found in TSB 14-28-21R.
STEP 3: Start the vehicle and allow to idle. Using the SSM, read the value the following four data monitor items
(ALWAYS Save SSM Data):
1. VVT Initial Position Learning Value #1
2. VVT Initial Position Learning Value #2
3. VVT EX Initial Position Learning Value #1
4. VVT EX Initial Position Learning Value #2

Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 3 of 15

Are all of the data monitor item values within the acceptable range listed in the table above?
YES - proceed to STEP 5.
NO - proceed to STEP 4.
STEP 4: Perform the procedures outlined in “#7 INSPECTION MODE N” and “#11
INSPECTION MODE T”. Then re-check the threshold values in STEP 3 along with the OBD MODE
test results (*1)
“#7 INSPECTION MODE N” procedure.
Using the applicable Service Manual, refer to: DIAGNOSTICS > ENGINE> Inspection Mode> #7
DRIVE CYCLE N
A. Confirm the battery voltage is 12 Volts or more and the fuel tank is at least half full.
B. Using SSM, clear the fault memory. Prepare the SSM to be kept in the vehicle during the
following road test.
C. With gear selector in the park position (neutral for MT models), idle the engine at
approximately 2500 rpm for 40 seconds or more.
D. Move the gear selector into the drive position (appropriate gear range for MT models.
Accelerate the vehicle to 31 mph or more.
E. When the vehicle speed is 31 mph or more, release the accelerator pedal and brake pedal
(and clutch for MT models) and allow the vehicle to decelerate without any gear shift
changes. Maintain the engine speed between 2500 rpm to 1900 rpm for 5 seconds during this
deceleration.
NOTE: Depending on road conditions, an appropriate gear might have to be selected to maintain the
desired engine speed. The vehicle speed is not important as long as the engine speed is within range
during the declaration.
F. In a suitable area, safely bring the vehicle full stop and allow it to idle for 5 minutes.
“#7 INSPECTION MODE N” procedure is complete. Proceed to “#11 INSPECTION MODE T”
procedure.
“#11 INSPECTION MODE T” procedure.
Using the applicable Service Manual, refer to: DIAGNOSTICS > ENGINE> Inspection Mode > #11
INSPECTION MODE T
A. Confirm the battery voltage is 12 Volts or more the fuel is at least half full.
B. Start the engine.
C. Allow the engine to idle for at least 3 minutes.
Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 4 of 15

D. Accelerate the vehicle speed to approximately 37 mph.
E. While maintaining approximately 37 mph, cycle the accelerator from a 0% to 20% opening
angle. Try to keep these cycles within 5 second intervals. Maintain this driving pattern for 20
minutes or more.
NOTE: It is acceptable to stop the vehicle if needed depending on road/traffic conditions during this
driving pattern.
F. Release the accelerator pedal and brake pedal (and clutch for MT models) and allow the
vehicle to decelerate with any gear shift changes.
G. In a suitable area, safely bring the vehicle full stop and turn off the engine.

“#11 INSPECTION MODE T” procedure is complete.
Read the threshold values from STEP 3 (pictured below) and the OBD MODE test results (*1)
Are all of the data monitor item values within the acceptable range listed in the table below? Are the
threshold values between -1000 to + 1000?

YES - The procedure is FINISHED.
NO - Repeat STEP 4 ONE TIME ONLY and if the result answer is still “NO”, proceed to STEP 6.
STEP 5: Perform the “#7 INSPECTION MODE N” and “#11 INSPECTION MODE T” procedure.
“#7 INSPECTION MODE N” procedure.
Using the applicable Service Manual, refer to: DIAGNOSTICS > ENGINE> Inspection Mode > #7
INSPECTION MODE N
A. Confirm the battery voltage is 12 Volts or more the fuel is at least half full.
B. Using SSM, clear the fault memory. Prepare the SSM to be kept in the vehicle during the
following road test.
C. With gear selector in the park position, idle the engine at approximately 2500 rpm for 40
seconds or more.
Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 5 of 15

D. Move the gear selector into the drive position. Accelerate the vehicle to 31 mph or more.
E. When the vehicle speed is 31 mph or more, release the accelerator pedal and brake pedal, allow
the vehicle to decelerate without any gear shift changes. Maintain the engine speed between 2500
rpm to 1900 rpm for 5 seconds during this deceleration.
NOTE: Depending on road conditions, an appropriate gear might have to be selected to maintain the
desired engine speed. The vehicle speed does is not important as long as the engine speed is within range
during the declaration.
F. In a suitable area, safely bring the vehicle full stop and allow it to idle for 5 minutes.
“#7 INSPECTION MODE N” procedure is complete. Proceed to “#11 INSPECTION MODE T”
procedure.
“#11 INSPECTION MODE T” procedure.
Using the applicable Service Manual, refer to: DIAGNOSTICS > ENGINE> Inspection Mode > #11
INSPECTION MODE T
G. Confirm the battery voltage is 12 Volts or more the fuel is at least half full.
H. Start the engine.
I. Allow the engine to idle for at least 3 minutes.
J. Accelerate the vehicle speed to approximately 37 mph.
K. While maintaining approximately 37 mph, cycle the accelerator from a 0% to 20% opening
angle. Try to keep these cycles within 5 second intervals. Maintain this driving pattern for 20
minutes or more.
NOTE: It is acceptable to stop the vehicle if needed depending on road/traffic conditions during this
driving pattern.
L. Release the accelerator pedal and brake pedal (and clutch for MT models) and allow the vehicle
to decelerate with any gear shift changes.
M. In a suitable area, safely bring the vehicle full stop and turn off the engine.
“#11 INSPECTION MODE T” procedure is complete.
N. Using SSM, select Diagnosis > Each System > Engine > DTC > Readiness Code

Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 6 of 15

O. Read the readiness codes for P0016, P0017, P0018, P0019, P000A, P000B, P000C, and P000D.
Confirm the self-diagnosis is complete and that the codes are not pending.

P. Check the DTC and data monitor threshold values. Using SSM, select Diagnosis > Select
Vehicle > OBD System – Each System > ECM-EngineControl > OBD MODE test results (*1)
Are there NO DTCs present and the threshold values between -1000 to + 1000?
YES - The procedure is FINISHED.
NO - Proceed to STEP 6

STEP 6: Inspect the engine oil level and condition.
IMPORTANT: If the engine oil and filter were replaced prior to diagnosis, there is no need for
inspection. Proceed to STEP: 7.
Is there any abnormal condition or inappropriate oil level??
YES - Perform the engine oil and filter change. Repeat STEP 4 or STEP 5, then continue
diagnosis.
NO – Proceed to STEP 7

STEP 7: Performed the outlined timing chain inspection outlined below:
IMPORTANT: If the timing chain was replaced prior to diagnosis, there is no need to perform
the inspection. Proceed to STEP 8.
A. Using SSM, clear the fault memory.
B. Switch the ignition to the “OFF” position.
C. Disconnect the oil control solenoid valve connector on the bank with associated DTC.
D. Switch the ignition switch to the “ON” position.
Continued...
Bulletin Number: 09-128-24R; Revised: 11/14/24

Page 7 of 15

E. Using SSM and the engine not running, read the “VVTAdvance Angle Value” data monitor
value.
F. Start the engine and read the “VVTAdvance Angle Value” data monitor value for a duration of
10 seconds.
G. Switch the ignition to the “OFF” position.
Is the “VVTAdvance Angle Value” data monitor value out of -10 degrees to +10 degrees?
YES - Adjust and / repair the timing chain as needed. Repeat STEP 4 and STEP 5, then continue
diagnosis.
NO - Proceed to STEP 8.
STEP 8: Perform a visual inspection of the engine harness and the connectors specified below for any
physical damage.
IMPORTANT: If the engine harness was replaced prior to diagnosis, there is no need to perform
the inspection. Proceed to STEP 9.
Connectors:
•

ECM

•

Oil Control Solenoid

•

CAM Position Sensor

•

Crank Position Sensor

Was there any damage found?
YES - Repair the damaged harness and / or connector. Repeat STEP 4 and STEP 5, then continue
diagnosis.
NO – Proceed to STEP 9.
STEP 9: Perform the following Ohm tests:
A. Switch the ignition to the “OFF” position.
B. Disconnect the ECM and the Crank Position Sensor. Disconnect the Oil Control Valve and
Cam Position Sensor associated with the DTC.
C. Measure the resistance between the following connectors specified in the tables below and
record the results:
P0016
Right Intake Oil Control Solenoid
ECM

BRZ

Right Intake Camshaft Position
Sensor

Solenoid

ECM

Crankshaft Position Sensor

Sensor

ECM

Sensor

Connector

Terminal

Connector

Terminal

Connector

Terminal

Connector

Terminal

Connector

Terminal

Connector

Terminal

E53

99

E105

2

E53

78

E61

2

E53