TECHNICAL INSTRUCTIONS
FOR
CUSTOMER SUPPORT PROGRAM 22TE09
HV FLOOR UNDER WIRE HARNESS AND REAR TRACTION MOTOR CABLE
CORROSION

CERTAIN 2022 MODEL YEAR NX450H+

The repair quality of covered vehicles is extremely important to Lexus. All dealership technicians
performing this recall are required to successfully complete the most current version of the E-Learning
course “Safety Recall and Service Campaign Essentials”. To ensure that all vehicles have the repair
performed correctly; technicians performing this recall repair are required to complete the following
course:
•

LIC209A – EPV Repair

It is the dealership’s responsibility to select technicians with the above certification level or greater to
perform this recall repair. Carefully review your resources, the technician’s skill level, and ability before
assigning technicians to this repair. It is important to consider technician days off and vacation
schedules to ensure there are properly trained technicians available to always perform this repair.

I.

OPERATION FLOW CHART
Verify Vehicle Eligibility
1. Confirm vehicle VIN matches R.O.
2. Check vehicle is covered under CSP

Not Covered

No further action required.

Covered
Inspect the vehicle for DTC and or AM
static

Vehicle not affected

Condition confirmed

Does the Rear Traction Motor Cable have
corrosion on the chamfer per inspection

Yes

No

Replace HV Floor Under Wire

Replace both HV Floor Under Wire
Harness and Rear Traction Motor Cable

Repair Complete

II. BACKGROUND
Although the HV Floor Under Wire Harness and Rear Traction Motor Cable is covered by Lexus’s New Vehicle
Limited Warranty for 3 years or 36,000 miles (whichever comes first), we at Lexus care about the customers’
ownership experience. Lexus is providing coverage for repairs related to excessive corrosion to the wire harness
connections at the Rear Motor Generator. Excessive corrosion can cause AM Radio Static during certain drive
cycles, or the vehicle may not start.

III. IDENTIFICATION OF AFFECTED VEHICLES
•
•

Check TIS to confirm the VIN is involved in this Customer Support Program
TMS warranty will not reimburse dealers for repairs conducted on vehicles that are not affected

2

IV. PREPARATION
A. PARTS
Dealers are not to order parts for stock.
HV Floor Under Wire Harness Repair Parts
Part Number
Description
821H1- 78040
72693-06030
90917-A6002
17451-F0100
17173-25020
90177-A0021
90105-A0369
90068-14011
90099-14155

Qty

HV Floor Under Wire Harness
Rear Seat Cushion Hook Clips
Gasket, Exhaust Pipe
Gasket, Exhaust Pipe
Gasket, Exhaust Manifold to Head
Nut, Lock
Bolt, Flange

1
2
1
1
1
2
2
1
1

Ring, O, No. 3 for Liquid Tube
Ring, O, No. 9 for Discharge Tube

Rear Traction Motor Cable Parts: Only requires replacement based on inspection s.
Part Number
Description
Qty
G1149-42010
G114D-47021
90105-A0420
90119-A0512

Rear Traction Motor Cable
Cap Motor Cable Terminal
Bolt, w Washer
Bolt, W Washer

1
1
2
1

B. TOOLS & EQUIPMENT
•
•

GTS+
Basic Hand Tools

•
•

Transmission Jack
Torque wrench

•
•

Screw Jack
DVOM

SST- The following tools are essential service tools that all dealers are required to have.
Part Number
01413-00072 (Small)
01413-00073 (Medium)
01413-00074 (Large)

Part Description
Insulated Tools

Quantity
As needed

Insulated Glove Set, Rubber with Leather
Protectors*

1

CAUTION
ALWAYS inspect the insulated gloves before use for cracks, ruptures, tears, pinholes, or damage. Do
NOT wear if damaged.

V. CONFIRM CONDITION EXISTS AND CABLE INSPECTION
1) Perform a health check and confirm if DTC P0AA649 OR P1C8049 are present
YES – Continue to Step 3
NO – Continue to Step 2
For part release a screenshot is required of DTC from GTS+ and the VIN must be in screenshot.
2) Inspect the vehicle for AM static radio interference.
a) Ready on vehicle
b) Change the radio to a known AM station.
c) After the radio is on a known station, place the vehicle into Drive or Reverse while applying the brake.
d) Return the vehicle to Park after 3 seconds.
e) Repeat (c) and (d) 3 times.
When placing the vehicle into drive or reverse is AM static introduced each time placed into Drive or Reverse?
YES – Continue to Step 3
NO – This CSP does not apply. Please consult the repair manual and continue the diagnosis.
For part release, vehicles with No DTC and Only AM static radio, will require a video with audio of the
AM static radio interference.
3

3) Disable High Voltage Circuit for Inspection.
a) Temporarily disconnect 12 v battery.
b) Remove the hybrid service plug.
c) Remove bolt (b) at the inverter as shown.
d) Using a T25 "TORX" socket wrench, remove the bolt (a)and
connector cover assembly from the inverter with converter
assembly.
NOTICE:
• Do not touch the connector cover assembly waterproof seal.
• Do not allow any foreign matter or water to enter the inverter
with converter assembly.
e) Using a voltmeter, measure the voltage between the
terminals of the 2-phase connectors.
Standard Voltage: 0 V
NOTICE: Do not allow any foreign matter or water to enter the
inverter with converter assembly.
HINT: Use a measuring range of DC 750 V or more on the
voltmeter.
CAUTION
Be sure to wear insulated gloves.

4) Remove No. 1 Floor Under Cover
a) Remove the 3 bolts, 3 clips, and No. 1 floor under cover
from the rear suspension member sub-assembly.

4

Y6 connector under the vehicle at MGR

5) Inspect the Y6 connection for corrosion.
f) Disconnect the Y6 connector at the MGR and inspect for
corrosion, dirt, or debris.
CAUTION
Orange wire harnesses and connectors indicate high-voltage
circuits. To prevent electric shock, always follow the procedure
described in the repair manual to disable
the high-voltage system.
To prevent electric shock, wear insulated gloves when working on
wire harnesses and components of the high-voltage system.

YES – Continue to Section VI.
For parts release take a photo of the connector housing with
R.O. in the picture.
NO - This CSP does not apply. Please consult the repair
manual and continue the diagnosis.
6) Inspect the connector housing of the MGR.
a) Inspect the chamfer of the MGR connector housing for pitting and corrosion on the sealing surface.
Corrosion in this area will cause the seal to leak. Are pitting and corrosion present?
YES – Rear Traction Motor Cable requires replacement continue to Section VI.
Take a photo of the connector housing with R.O. in the picture for parts release.
NO – Cable does NOT require replacement continue to Section VI.

NG

VI. CABLE REMOVAL PROCEDURE
A. HV FLOOR UNDER WIRE REMOVAL
1. Remove the HV Floor Under Wire following the repair manual procedure.
Refer to TIS, applicable model, and model year Repair Manual:
• 2022 NX450H+:

“Engine/Hybrid System – Hybrid/Battery Control System – “Hybrid / Battery Control:
Frame Wire: Removal”

5

B. REAR TRACTION MOTOR CABLE REMOVAL (if required, if not required skip to Section VII.B)
1. Disconnect MGR Ground Plug/Sensor (if equipped).

a) Remove the bolt from the ground and bracket.

2. Place the transmission jack under MGR and secure it.

6

3. Remove MGR mounting bolts.

a
a) Remove the MGR rear mount bolt.
b) Remove the front mount inner bolts (Do not remove outer
bolts).
c) Slowly tilt the MGR assembly 3 inches to gain clearance with
the body. (Do not remove assembly).

b
4. Remove the Rear Traction Motor Cable side mount bolts.

V

5. Remove Motor Cable Terminal Cap (Non-Reusable).
a) Slide the cover on the top side of the rear traction motor cable.
b) Clean the area with shop air and rag around the cover to avoid
debris falling in.
NOTICE:
• Some vehicles may be extremely dirty in this area, ensure
you clean thoroughly before removing the cover.

7

c) Disengage the 2 claws to remove the motor cable terminal cap
from the rear traction motor with transaxle assembly.

6. Rear Traction Motor Cable.
a) Remove Rear Traction Motor Cable High Voltage Mount Bolts.

b) Remove Rear Traction Motor Cable from MGR Assembly.

8

VII. CABLE INSTALL PROCEDURE
A. REAR TRACTION MOTOR CABLE INSTALLATION (if required, if not required skip to Section VII. B)
1. Install the Rear Traction Motor Cable onto the MGR.
a) Clean the area around the terminal of the rear traction motor
cable, and then blow air on the terminal to remove dust and
other foreign matter.
NOTICE:
• Blowing air without cleaning first may cause dust and other
foreign matter to enter the terminal.
• Dust or other foreign matter entering the terminal when
installing the rear traction motor cable may cause a short
or electrical leakage.
b) Using an insulated tool, install the rear traction motor cable to
the rear traction motor with transaxle assembly with the 3 bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
Torque is critical at this electrical connection. Ensure
proper torque is applied to each bolt.
2. Install the new motor cable terminal cap.
a) Engage the 2 claws to install a new motor cable terminal cap to
the rear traction motor with transaxle assembly.
NOTICE:
• Do not pinch the O-ring.
• Check that the motor cable terminal cap is properly
installed.
b) Slide the cover on the top side of the rear traction motor cable.

3. Install the 4 bolts for the rear traction motor cable.
Torque:
22 N·m {224 kgf·cm, 16 ft·lbf}

9

4. Raise the MGR with Transmission Jack.

5. Reinstall the MGR mounting bolts.
a) Temporarily install bolts (A) and (B).
b) Torque bolts to specification starting with (A) and then moving
to (B).

A

A

Torque:
for bolts A :
55 N·m {561 kgf·cm, 41 ft·lbf}
for bolt B :
130 N·m {1326 kgf·cm, 96 ft·lbf}

B

c) After tightening bolt (B), make sure the inner cylinder mark (a)
and rubber part mark (b) are positioned as shown.

10

6. Reinstall MGR Ground Plug/Sensor.
a) Reinstall ground wire to bracket with bolt and torque to
specification.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}

B. INSTALL THE HV FLOOR UNDER WIRE
1. Install the HV Floor Under Wire following the repair manual procedure.
Refer to TIS, applicable model, and model year Repair Manual:
• 2022 NX450H+:

Engine/Hybrid System – Hybrid/Battery Control System – “Hybrid / Battery Control:
Frame Wire: Installation”
NOTICE: When installing the new HV Floor Under Harness ensure to leave the cover on the wire harness
for the inverter connector to protect it during the installation and routing.

2. Using GTS+, run a Health Check to verify DTCs P0AA649 and/or P1C8049 are no longer present.
3. Test-drive the vehicle to ensure the condition no longer exists and the vehicle exhibits proper operation.

◄ VERIFY REPAIR QUALITY ►
−
−
−
−

Confirm the high voltage bolts are properly torqued to specification.
Confirm the MGR bolts are torqued to specification and that the rear mount is properly aligned.
Confirm the cables are properly routed and secured.
Confirm related DTCs P0AA649 and/or P1C8049 are no longer present.
If you have any questions regarding this update, please contact your regional representative.

11