Customer Satisfaction Program
N242451030 Multiple Module Reprogramming
Release Date:
Revision Description:
Attention:

November 2024

Revision:

02

This bulletin has been revised to remove radio reprogramming. Please discard all
previous copies of N242451030.

This program is in effect until October 31, 2026.

Make
Chevrolet
GMC

Model
Colorado
Canyon

Model Year
From
To
2023

RPO

Description

2023

Involved vehicles are marked “Open” on the Investigate Vehicle History screen in GM Global Warranty Management
system. This site should always be checked to confirm vehicle involvement prior to beginning any required inspections
and/or repairs.
Condition
Correction

Certain 2023 model year Chevrolet Colorado and GMC Canyon vehicles may require software updates
that improve the customer experience and optimize future over-the-air updates.
Dealers will perform a comprehensive software update.

Parts
No parts are required for this repair.
Warranty Information
Labor
Operation
9500009*

Description
Vehicle Wide Programming

ADD: Set up

Labor Time
Use Vehicle
Wide
Programming
receipt time**

Trans.
Type

Net
Item

ZFAT

N/A

0.2

**In base time field, enter time shown on Vehicle Wide Programming receipt. Round up to nearest .10.
Important:

* To avoid warranty transaction rejections, carefully read and follow the instructions below.

Note: For issues related to Warranty Administration, refer to bulletin 24-NA-132.

6125814

• The Warranty Claim Code and Total Time from the programming event must be accurately entered in the
“Warranty Claim Code” field of the transaction.
•

When more than one Warranty Claim Code is generated for a programming event, it is required to document all
Warranty Claim Codes in the “Correction” field on the job card. Dealers must also enter one of the codes in the
“Warranty Claim Code” field of the transaction, otherwise the transaction will reject. It is best practice to enter
the FINAL code provided by SPS2.

For information on submitting Vehicle Wide Programming field action claims, please refer to Warranty Administration
Bulletin (24-NA-132).
Copyright 2024 General Motors. All Rights Reserved.

Page 1 of 6

Customer Satisfaction Program
N242451030 Multiple Module Reprogramming
Warranty Claim Code Information Retrieval

6693878

If the Warranty Claim Code was not recorded on the Job Card, the code can be retrieved in the SPS2 system as
follows:
1.
2.
3.
4.

Open TLC on the computer used to program the vehicle.
Select and start SPS2.
Select Settings (1).
Select the Warranty Claim Code tab (2).

The VIN, Warranty Claim Code and Date/Time will be listed on a roster of recent programming events. If the code is
retrievable, dealers should resubmit the transaction making sure to include the code in the SPS Warranty Claim Code
field.
Service Procedure
Caution: Before downloading the update files, be sure the computer is connected to the internet through a network cable
(hardwired). DO NOT DOWNLOAD or install the files wirelessly. If there is an interruption during programming,
programming failure or control module damage may occur.
Note: Carefully read and follow the instructions below.

•

Ensure the programming tool is equipped with the latest software and is securely connected to the data link connector.
If there is an interruption during programming, programming failure or control module damage may occur.

•

Stable battery voltage is critical during programming. Any fluctuation, spiking, over voltage or loss of voltage will
interrupt programming. Install a GM Authorized Programming Support Tool to maintain system voltage. Refer to
www.gmdesolutions.com for further information. If not available, connect a fully charged 12 V jumper or booster
pack disconnected from the AC voltage supply. DO NOT connect a battery charger.

•

Follow the on-screen prompts regarding ignition power mode but ensure that anything that drains excessive power
(exterior lights, HVAC blower motor, etc) is off.

•

Clear DTCs after Vehicle Wide Programming is complete. Clearing powertrain DTCs will set the
Inspection/Maintenance (I/M) system status indicators to NO.

Important: The service technician always needs to verify that the VIN displayed in the TLC left side drop down menu and
the top center window match the VIN plate of the vehicle to be programmed prior to using Service Programming System
2 (SPS2) for programming or reprogramming a module.

•

For the TLC application, service technicians need to always ensure that the power mode (ignition) is “ON” before
reading the VIN from the vehicle’s VIN master module and that they do not select a VIN that is already in the TLC
application memory from a previous vehicle.

•

If the VIN that shows up in the TLC top center window after correctly reading the VIN from the vehicle does not match
the VIN plate of the vehicle, manually type in the VIN characters from the vehicle VIN plate into the TLC top center
Page 2 of 6

Customer Satisfaction Program
N242451030 Multiple Module Reprogramming
window and use these for programming or reprogramming the subject module with the correct vehicle VIN and
software and/or calibrations.

•

The Engine Control Module (ECM) is the primary module (for VIP ICE vehicles) that TLC reads to determine the VIN
of the vehicle. If the VIN read from the vehicle by TLC does not match the VIN plate of the vehicle, the ECM also
needs to be reprogrammed with the correct VIN, software and calibrations that match the vehicle’s VIN plate.

Caution: Be sure the VIN selected in the drop-down menu (1) is the same as the vehicle connected (2) before beginning
programming.

5743643

Important: If the vehicle VIN DOES NOT match, the message below will be shown.

5877000

5644477

Important: Techline Connect screens shown above.
Important: Vehicle Wide Programming will only work with a wired MDI2 connection. It is also necessary to
remove any wireless dongles from the computer being used as these will not allow the Vehicle Wide
Page 3 of 6

Customer Satisfaction Program
N242451030 Multiple Module Reprogramming
Programming to be selectable. If the Vehicle Wide Programming is not selectable with a wired MDI2,
confirm it shows disconnected in SPS2 and then (if needed) exit out of TLC and log-in again.
Important: It is critical to remove ALL aftermarket devices connected to the DLC and all USB devices
connected to the vehicle USB ports. Additionally, all wireless Bluetooth USB connectors (mouse, keyboard,
etc.) MUST be disconnected from the computer prior to opening Techline Connect.
1.

Perform Vehicle Wide Programming. Refer to: 24-NA-113 in SI. Please read the bulletin in its entirety prior to
programming the vehicle.

2.

Verify all applicable modules display “SUCCESS” or “SKIPPED”, excluding the A11 Radio which is NOT supported
by Vehicle Wide Programming and was manually updated in the previous steps.
•

If any applicable module does NOT display “SUCCESS” or “SKIPPED”:
2.1 Attempt Vehicle Wide Programming a second time.
2.2 If any applicable module fails the second attempt, attempt to program the module
individually through SPS. If the failure continues, contact Techline Customer Service Center.
2.3 Perform Vehicle Wide Programming an additional time to receive a “Status Completed” or
“Status Blocked” message, allowing the field action to be closed. Proceed to step 3.

•

If all modules have successfully updated, proceed to step 3.

6693875
Note: The screenshot above is an example of Vehicle Wide Programming and may not be indicative of the specific
modules that are being programmed. VIN information has been blacked out.
Important: To avoid warranty transaction rejections, you MUST record the Total Time provided on the Warranty
Claim Code (WCC) screen shown above on the job card.
3.

Print a copy of the Warranty Claim Code screen and attach to the repair order. “Status Completed” or “Status Blocked”
must be achieved to close out the field action. It is also critical to record the total time in order to close out the Field
Action.
Unsuccessful Programming
For Techline Connect Support Center help in the US, please open a TCSC support case in the Dealer Case
Management tool, located within Global Connect. Go to the app center and type in “Dealer Case Management
System and Resources”, and then select “New Techline Case”. For all other regions use:
Canada: 1-800-828-6860 (English) / 1-800-503-3222 (French) 8-8 EST Monday-Saturday
Mexico: 800-522-9984

Page 4 of 6

Customer Satisfaction Program
N242451030 Multiple Module Reprogramming
Dealer Responsibility
All new, used, GM Certified Pre-Owned (CPO), courtesy transportation vehicles, dealer shuttle vehicles, CarBravo, etc.
in dealers' possession and subject to this field action must be held and inspected/repaired per the service procedure of
this bulletin before customers take possession of these vehicles. Involved vehicles must be held and not delivered to
customers, dealer-traded, released to auction, used for demonstration, or any other purpose.
All GM Certified Pre-Owned (CPO) vehicles currently in the dealers’ inventory within the SHIFT Digital system will be
de-certified and must be held and remedied per the service procedure in this bulletin. Upon submitting an accepted/paid
warranty transaction in the Global Warranty Management (GWM) system, the vehicle can be re-certified for sale within
the SHIFT Digital system, or once again be used in the Courtesy Transportation Program.
Dealers are to service all vehicles subject to this program at no charge to customers, regardless of mileage, age of vehicle,
or ownership, through October 31, 2026. Customers who have recently purchased vehicles sold from your vehicle
inventory, and for which there is no customer information indicated on the involved vehicle listing, are to be contacted by
the dealer. Arrangements are to be made to make the required correction according to the instructions contained in this
bulletin. A copy of the customer letter is provided in this bulletin for your use in contacting customers. Program followup cards should not be used for this purpose, since the customer may not as yet have received the notification letter.
In summary, whenever a vehicle subject to this program enters your vehicle inventory or is in your facility for service
through October 31, 2026, you must take the steps necessary to be sure the program correction has been made before
selling or releasing the vehicle.
Dealer Reports – For USA & Export
For dealers with involved vehicles, a listing has been prepared and will be available through GM GlobalConnect Maxis
Field Action Reports or sent directly to export dealers. The Inventory tab of the dealer reports will contain VINs that
apply to this field action. This information is intended to assist dealers with the PROMPT COMPLETION of these
vehicles. The Customer In-Service tab will contain customer names and addresses from Motor Vehicle Registration
Records. The use of such motor vehicle registration data for any purpose other than follow-up necessary to complete
this field action may be a violation of law in several states.
Courtesy Transportation – For USA & Canada
Courtesy transportation is available for customers whose vehicles are involved in a product program and still within the
warranty coverage period. See General Motors Service Policies and Procedures Manual for courtesy transportation
program details.
Customer Notification
USA & Canada - General Motors will notify customers of this program on their vehicle. (see copy of customer letter
included with this bulletin).

GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of
conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained
technicians have the tools, equipment, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT
assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your dealer for information on whether your
vehicle may benefit from the information.

We Support
Voluntary Technician
Certification

Page 5 of 6

Customer Satisfaction Program
N242451030 Multiple Module Reprogramming

September 2024
This notice applies to your vehicle, VIN: ________________________________
Dear General Motors Customer:
Your vehicle is due for a software update that must be performed at the dealership. Our highest priority is ensuring that
you have the best ownership experience possible.
What We Will Do: Your GM dealer will perform a comprehensive software update. This service will be performed for
you at no charge until October 31, 2026. After that, any applicable warranty will apply.
Once completed, your vehicle will have up-to-date technology, including the latest infotainment features, performance
enhancements, and more.
What You Should Do: To limit any possible inconvenience, we recommend that you contact your dealer as soon as
possible to schedule an appointment for this repair.
If you have any questions or concerns that your dealer is unable to resolve, please contact the appropriate Customer
Assistance Center at the number listed below.
For the hearing or speech impaired, please contact our Customer Assistance Center using the Telecommunication
Relay Service by dialing 711 then providing the appropriate Customer Assistance Center number for your vehicle.
Division
Chevrolet
GMC
Puerto Rico – English
Puerto Rico – Español
Virgin Islands

Number
1-800-222-1020
1-800-462-8782
1-866-467-9700
1-866-467-9700
1-866-467-9700

Our highest priority is ensuring that you get the best driving experience possible.
Neelie O’Connor
Global Executive Director
Customer Experience Operations
N242451030

Page 6 of 6

GENERAL MOTORS
DCS7069
URGENT - DISTRIBUTE IMMEDIATELY
Date:

November 4, 2024

Subject: REVISION: N242451030-02 – Customer Satisfaction Program
Multiple Module Reprogramming
Revised Warranty and Procedure sections
Models: 2023 Chevrolet Colorado
2023 GMC Canyon

This bulletin has been revised to remove radio reprogramming. Please
discard all previous copies of N242451030.

END OF MESSAGE