NHTSA ID Number: 11006914
Manufacturer Communication Number: 2024.32_0824.pdf
TSB/Document Date: 2024-09-04
Summary
Tesla does not provide physical owner's manual copies. Instead, all available owner’s manual content is integrated into the vehicle software, and only the content relevant for a given vehicle, based on vehicle configuration and software version installed, is displayed on its touchscreen. This file contains all available owner’s manual content for the vehicle converted to PDF format, and given the distribution method and NHTSA’s submission format requirements, it is the best available representative copy of owner’s manual content. However, a customer who accesses the owner’s manual via their vehicle’s touchscreen would only see the parts of this PDF file that are relevant to their vehicle.
Cargo - Weight Limits
CAUTION: Exceeding the weights specified can cause damage not covered by the warranty.
The front trunk and under bed compartments are designed to hold the following weights:
Front Trunk
Maximum 441 lb (200 kg)
Under Bed Compartment
Maximum 220 lb (100 kg)
Cargo - Volumes
WARNING: The loading capacity of your vehicle is limited either by how much space is available (volume capacity) or by
how much weight the vehicle can carry (payload capacity). When you have loaded Cybertruck to its maximum weight
capacity, do not add more cargo, even if there is space available. Overloading, or improper loading, can contribute to
property damage, personal injury, or death.
Location
Cubic Feet
Front trunk
7.1
200
Cargo Bed (enclosed) - Above load floor
56.2
1,591
Cargo Bed - Lower storage compartment
3.4
Cabin - Behind front seats with rear seat cushions folded up
54.2
Owner's Manual
Liters
97
1,533
1053
Specifications
Location
Cubic Feet
Liters
Total volume with five passengers
66.7
1,888
Total volume with two passengers
120.9
3,421
Subsystems
Motor Type
Motor Type Dual Motor
Tri-Motor
Front
One AC induction motor, liquid-cooled, with variable
frequency drive.
One AC permanent magnet synchronous motor,
liquid-cooled, with variable frequency drive.
Rear
One AC permanent magnet synchronous motor,
liquid-cooled, with variable frequency drive.
Two AC induction motors, liquid-cooled, with variable
frequency drive.
Transmission
Type
Dual Motor
Tri-Motor
Type
Single speed fixed gear
Single speed fixed gear
Overall Final Drive
Ratio
Front and Rear unit motors: 15.02:1
Front unit motor: 15.02:1
Rear unit motor: 2
Independent Gearsets: 15.02:1
Reverse Gear
Reverse direction of motor, limited to
15 mph (24 km/h).
Reverse direction of motor, limited to 15 mph (24 km/h).
Specifications
Type
4-wheel directional steer-by-wire
Number of turns lock to lock
0.94 (340 degrees)
Turning Circle (curb to curb)
Approximately 43.5 ft (13.25 meters)
Specifications
Type
4-wheel anti-lock braking system (ABS) with Electronic Brake Force
Distribution, Integrated Advanced Stability Control and Electronic
Accelerator pedal actuated regenerative braking system.
Calipers
Front: Four piston, fixed
Rear: Single piston, floating
Rotor Diameters (ventilated)
Front: 13.8 in (351 mm)
Rear: 14 in (356 mm)
Front Rotor thickness
1054
New: 1.26 in (32 mm)
Owner's Manual
Specifications
Brakes
Specifications
Service limit: 1.18 in (30 mm)
Rear Rotor thickness
New: 0.91 in (23 mm)
Service limit: 0.83 in (21 mm)
Front Brake Pad Thickness (excluding back
plate)
New: 0.39 in (10 mm)
Rear Brake Pad Thickness (excluding back
plate)
New: 0.43 in (11 mm)
Electrically actuated parking brake calipers
Service limit: 0.12 in (3 mm)
Service limit: 0.08 in (2 mm)
Specifications
Front
Independent, double wishbone, air spring with adaptive damper, stabilizer bar.
Rear
Independent, double wishbone, air spring with adaptive damper, stabilizer bar.
Battery - Low Voltage
Battery - Low Voltage
Specifications
Rating
4 amp hour
Voltage
48V
Battery - High Voltage
Battery - High Voltage Specifications
Type
Liquid-cooled lithium ion (Li-ion)
Nominal Voltage
700V DC
Temperature Range
Do not expose CybertruckModel SModel X to ambient temperatures above 149° F (65° C) or
below -22° F (-30° C) for more than 24 hours at a time.
Owner's Manual
1055
Instructions for Transporters
Instructions for Transporters
DO NOT TRANSPORT WITH WHEELS ON THE GROUND
The front motor and rear motor(s) in CybertruckModel SModel X may generate power when the wheels spin. Always transport
CybertruckModel SModel X with all four tires off the ground. Ensure that the tires are unable to spin at any time during
transport.
WARNING: NEVER TRANSPORT YOUR VEHICLE WITH THE TIRES IN A POSITION WHERE THEY CAN SPIN. DOING SO
CAN LEAD TO SIGNIFICANT DAMAGE AND OVERHEATING. IN RARE CASES EXTREME OVERHEATING MAY CAUSE
THE SURROUNDING COMPONENTS TO IGNITE.
Do not transport CybertruckModel SModel X using any method that is not specified by Tesla. Adhere to the instructions
provided here and observe all warnings and cautions. Damage caused by improper transporting of your vehicle is not covered
by the warranty.
NOTE: Tesla is not liable or responsible for reimbursing services not dispatched through Tesla Roadside Assistance.
Approved Methods for Transporting
A flatbed truck or comparable transport vehicle is the recommended method of transporting CybertruckModel SModel X.
CybertruckModel SModel X can face either direction on the truck bed.
CAUTION: Use a flatbed truck with a bed that is at least 21 ft (6.5 meters) long (A). Before attempting to tow
CybertruckModel SModel X, always check the tow truck's recommended loading capacity against the gross vehicle
weight rating (GVWR) of CybertruckModel SModel X (see Dimensions, Weights, and Cargo Capacity on page 1050) to
ensure that the flatbed truck is capable.
Activate Transport Mode before repositioning CybertruckModel SModel X (if necessary) and winching it onto a flatbed tow
truck. For more information, see Activate Transport Mode on page 1058.
1056
Owner's Manual
Instructions for Transporters
If CybertruckModel SModel X has no low voltage power, attempt to jump start the low voltage system first so that you can
then activate Transport Mode. For more information about jump starting, see If Vehicle Has No Power on page 1057.
CAUTION: CybertruckModel SModel X uses steer-by-wire technology. As a result, you will be unable to use the steering
wheel to turn the wheels if CybertruckModel SModel X has no power.
NOTE: Do not transport CybertruckModel SModel X with the front or rear wheels on dollies unless absolutely necessary for a
short distance. If you are transporting CybertruckModel SModel X on dollies, ensure that a steering wheelsteering yoke (or
steering wheel) lock is applied and care is taken to prevent the front wheels from spinning.
CAUTION: Before using dollies, check the manufacturer's specifications and recommended loading capacity against the
vehicle weight rating and axle weight rating of CybertruckModel SModel X, as specified by the vehicle certification label
(see Vehicle Loading on page 1046).
CAUTION: DO NOT TRANSPORT YOUR VEHICLE IF THERE IS ANY CHANCE OF ANY OF THE WHEELS SPINNING.
CAUTION: Tesla is not responsible for any damage caused by or during the transport of CybertruckModel SModel X,
including personal property damage or damage caused by using self-loading dollies or tire skates.
WARNING: CybertruckModel SModel X is equipped with high voltage and low voltage components that may be
compromised as a result of a collision (see Electric Vehicle Components on page 981). Before transporting
CybertruckModel SModel X, it is important to assume these components are energized. Always follow high voltage
safety precautions (wearing personal protection equipment, etc.) until emergency response professionals have
evaluated the vehicle and can accurately confirm that all high voltage systems are no longer energized. Failure to do so
may result in serious injury.
If Vehicle Has No Power
If CybertruckModel SModel X has no low voltage power:
1. Open the powered frunk. See Opening the Powered Frunk with No Power on page 1062.
2. Jump start the low voltage battery. See Jump Starting on page 1066.
CybertruckModel SModel X must have low voltage power to open the doors from the outside or use the instrument
clustertouchscreen.
WARNING: It may be more difficult to steer CybertruckModel SModel X when the vehicle is being supported by an
external low voltage power supply. The wheels may not be as responsive to the steering wheel as expected, and extreme
caution should be taken when repositioning CybertruckModel SModel X.
CAUTION: CybertruckModel SModel X uses a 48V low voltage architecture. As a result, some functions may be
unavailable or degraded if you are supporting CybertruckModel SModel X with less than 30V (for example, another
vehicle or a 12V portable jump starter
).
CAUTION: Avoid using low voltage components of CybertruckModel SModel X (such as the climate control system,
cabin USB-C ports, lights, etc.) when the vehicle is being supported by an external low voltage power supply. Doing so
may disable low voltage systems and make it necessary to jump start CybertruckModel SModel X again.
NOTE: Tow providers: If the vehicle ran out of range, see Running Out of Range on page 589 for more information on
transporting the vehicle to a charging station and preparing the vehicle to charge.
If you are unable to jump start CybertruckModel SModel X and the touchscreen is not accessible, use tire skates to reposition the rear tires, keeping front tires on the ground. When using tire skates, be sure to use skates of sufficient size to
avoid contact between the tire and the bed/pavement. Before using tire skates, always check the manufacturer's
specifications and recommended loading capacity.
Disable the Self-Leveling Air Suspension System
NOTE: If CybertruckModel SModel X has no low voltage power (or is being supported by an external low voltage power
supply) you will not be able to enter Jack Mode.
Your CybertruckModel SModel X is equipped with an air suspension system that automatically self-levels, even when the
vehicle is "asleep" and the touchscreen is powered off. To prevent damage, you must activate Jack Mode to disable selfleveling:
1. Touch Controls > Ride and Handling on the touchscreen.
Owner's Manual
1057
Instructions for Transporters
2. Press the brake pedal, and then touch Medium to maximize ride height.
3. Touch Controls > Service > Jack Mode.
NOTE: Jack Mode cancels if you touch the button again or when driving speed exceeds 4 mph (7 km/h).
Activate Transport Mode
Transport Mode keeps the parking brake disengaged while winching CybertruckModel SModel X onto a flatbed truck. When
active, Transport Mode displays a message indicating that the vehicle will remain free-rolling. The following are required to
enable Transport Mode:
• Low voltage power. If CybertruckModel SModel X has no low voltage power, attempt to jump start the low voltage system
so that you can use the touchscreen to activate Transport Mode (see If Vehicle Has No Power on page 1057).
• CybertruckModel SModel X must detect a key. Transport Mode is available only when a key is detected.
• Ensure the vehicle is not connected to a charger. Transport Mode is not available if CybertruckModel SModel X is still
plugged in.
To activate Transport Mode:
1. Ensure the vehicle is in Park and that it is not connected to a charge cable.
2. Chock the tires and make sure CybertruckModel SModel X is secure.
WARNING: Ensure that the wheels are secure and that CybertruckModel SModel X has continuous low voltage
support while it is in Transport Mode. If there is a loss of low voltage power (for example, if the low voltage battery
does not self-recover before activating Transport Mode or if the external power supply becomes disconnected)
there is a risk of rollaway.
3. Press and hold the brake pedal, and then on the touchscreen, touch Controls > Service > Towing. The touchscreen displays
a message reminding you how to properly transport CybertruckModel SModel X.
4. Touch Transport Mode. The Transport Mode button turns blue, and CybertruckModel SModel X is now free-rolling and can
slowly be rolled (no faster than walking speed) for short distances or winched.
WARNING: Power steering may be disabled when CybertruckModel SModel X is in Transport Mode. The steering
system may be less responsive and the steering wheel may be more difficult to turn. Use extreme caution when
repositioning the wheels of CybertruckModel SModel X while in Transport Mode.
To cancel Transport Mode, touch Transport Mode again.
NOTE: Transport Mode is only intended to allow for winching CybertruckModel SModel X onto a flatbed truck or repositioning
the vehicle out of a parking space. While in Transport Mode, the tires are allowed to rotate slowly (under 3 mph or 5 km/h) and
for a very short distance (less than 30 feet or 10 meters). Exceeding these boundaries can lead to significant damage and
overheating that is not covered by the warranty.
NOTE: If you are unable to activate Transport Mode (because, for example, the electrical system is not working and you are
unable to jump start the low voltage system), use tire skates to reposition CybertruckModel SModel X. Before doing so,
always check the manufacturer's specifications and recommended loading capacity.
Pull onto the Flatbed Truck From the Rear
To pull CybertruckModel SModel X from the rear, use the tow hitch:
1. Chock the tires.
2. Remove the rear tow hitch cover. See Accessing the Trailer Hitch Assembly on page 893.
3. Attach the winch cable to the cutouts on either side of the tow hitch.
1058
Owner's Manual
Instructions for Transporters
4. Activate Transport Mode. See Activate Transport Mode on page 1058.
NOTE: If CybertruckModel SModel X has no low voltage power, you will need to jump start it before activating Transport
Mode. See If Vehicle Has No Power on page 1057.
5. Remove the tire chocks.
6. Pull CybertruckModel SModel X slowly onto the flatbed truck.
7. If CybertruckModel SModel X is in Transport Mode, deactivate it by touching Transport Mode again.
Pull onto the Flatbed Truck From the Front
To pull CybertruckModel SModel X onto a flatbed truck from the front, use one or both of the square tow hooks beneath the
front fascia:
1. Chock the tires.
2. Attach the winch cable to the tow hook(s). Either one or both tow hooks can be used.
3. Activate Transport Mode. See Activate Transport Mode on page 1058.
NOTE: If CybertruckModel SModel X has no low voltage power, you will need to jump start it before activating Transport
Mode. See If Vehicle Has No Power on page 1057.
4. Remove the tire chocks.
5. Pull CybertruckModel SModel X slowly onto the flatbed truck.
6. If CybertruckModel SModel X is in Transport Mode, deactivate it by touching Transport Mode again.
Owner's Manual
1059
Instructions for Transporters
Secure the Tires
The vehicle's tires must be secured onto the flatbed using the eight-point tie-down method.
• Remove any wheel covers before securing the tires.
CAUTION: Failure to remove wheel covers before attaching tie-down straps may result in damage to the wheel
covers.
• Ensure any metal parts on the tie-down straps do not touch the face of the wheels.
• Do not place tie-down straps over body panels or through the wheels.
CAUTION: Attaching the tie-down straps to the chassis, suspension or other parts of the vehicle's body may cause
damage.
1060
Owner's Manual
In Case of Emergency
Contacting Tesla Roadside Assistance
Tesla Roadside Assistance is available to you 24 hours a day, 365 days a year, for the duration of your warranty period. Tesla
Roadside Assistance is also available to speak with roadside service professionals to answer any questions and explain the
proper procedure for transporting your vehicle.
When contacting Tesla Roadside Assistance, please provide:
• The Vehicle Identification Number (VIN). The VIN is displayed when you touch Controls > Software. The VIN can also been
seen by looking through the driver's side of the windshield.
• Your exact location.
• The nature of the problem.
If available in your region, you can also expedite your request, by choosing the Roadside Assistance option in the Tesla mobile
app.
NOTE: For a detailed description of Tesla's Roadside Assistance policy, go to the support page on the Tesla web site for your
region.
Regional Phone Number(s)
Canada: 1-877-79TESLA (1-877-798-3752)
Mexico: 800-228-8145
United States: 1-877-79TESLA (1-877-798-3752)
NOTE: The phone number is also available by touching Controls > Service.
Owner's Manual
1061
In Case of Emergency
Running Out of Range
CAUTION: It is your responsibility to monitor the state of the high voltage Battery and the remaining range of your
vehicle. Do not assume that there is any range available when the range displayed on the instrument clustertouchscreen
is at 0 miles (0 km) (or 0%). Damage to the low voltage battery due to running out of range is not covered by the
warranty.
NOTE: In the unlikely event your vehicle runs out of range while driving, pull over when safe to do so and contact Tesla
Roadside Assistance on page 588 or your preferred tow provider.
If CybertruckModel SModel X runs out of range, the low voltage battery is no longer supported – and when low voltage is not
supported, the vehicle cannot charge. Therefore, the low voltage battery must be supported by an external power supply to
allow you to charge the High Voltage (HV) Battery. Once the vehicle begins charging, the external power supply is no longer
required.
If CybertruckModel SModel X runs out of range, the low voltage system is no longer supported – and when the low voltage
battery runs out of power, the vehicle cannot charge. Therefore, the low voltage system must be supported by an external
power supply to allow you to charge the High Voltage (HV) Battery. Once the vehicle begins charging, the external power
supply is no longer required.
In the case of running out of range away from a charger, the tow provider should transport CybertruckModel SModel X to the
nearest charging station and unload the vehicle within the charging cable's reach. Once the vehicle is positioned next to a
charger, follow these instructions:
NOTE: If the vehicle is being transported to a charger, make sure the tow provider does not leave until confirming that the
vehicle's high voltage Battery is successfully charging.
1. Jump start the low voltage system (see Jump Starting on page 595Jump Starting on page 1066). The low voltage battery
must be jump started to support the high voltage Battery.
2. Wait a few minutes. Once the touchscreen powers on, plug the charge cable into CybertruckModel SModel X to begin
charging the high voltage Battery.
3. When CybertruckModel SModel X begins to charge, disconnect the external power supply from the low voltage battery
jump posts.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the external
power source is active may cause arcing.
NOTE: If CybertruckModel SModel X is still not able to shift into Drive after charging the high voltage Battery, the low
voltage battery may need additional time to recover. Reconnect the charge cable, wait several minutes, disconnect the
charge cable, and then try again.
Before transporting to a non-Tesla charger, ensure your vehicle is equipped with an adapter that accommodates the specific
type of charging station you will be using. Even at a non-Tesla charger, you will need to jump start the low voltage system
before you can begin charging.
CAUTION: Always ensure CybertruckModel SModel X has enough range for your drive, or for being stored for an
extended period. Do not rely on the range estimates displayed on the touchscreen or mobile app as range can decrease
faster than projected due to ambient temperature, driving habits, wind, vehicle settings (such as Sentry Mode), etc.
NOTE: Towing your vehicle as a result of running out of range is not covered by the warranty.
Opening the Powered Frunk with No Power
In the unlikely event that CybertruckModel SModel X has no low voltage power, you will be unable to open the powered frunk
using the touchscreen, mobile app, or powered frunk button.
It is necessary to open the powered frunk before attempting to jump start CybertruckModel SModel X. For more information,
see Jump Starting on page 1066.
To open the powered frunk when CybertruckModel SModel X has no power, you need a power source that provides between
9V and 16.5V (such as a 12V portable jump starter or another vehicle), or a power source that provides between 30V and 50V.
A standard 9V battery may not have enough power to open the powered frunk if CybertruckModel SModel X has no power.
Instead, use a portable jump starter or another vehicle.
1062
Owner's Manual
In Case of Emergency
The steps below assume you are using an external low voltage power supply (such as a portable jump starter).
NOTE: The following steps do not open the powered frunk if CybertruckModel SModel X is locked and has low voltage power.
1. Locate the front trunk access terminal beneath the front-left wheel well, behind the headlights.
2. Use your finger to loosen the cover, then pull it down and toward you to remove it and expose the terminals. The cover is
attached to a loop of cable containing both the red positive (+) and the black negative (-) terminals.
3. Carefully pull the terminals out from the cavity.
Owner's Manual
1063
In Case of Emergency
4. Connect the low voltage power supply's red positive (+) cable to the red positive (+) terminal.
5. Connect the low voltage power supply's black negative (-) cable to the black negative (-) terminal.
NOTE: Applying external low voltage power to these terminals only releases the hood latches. You cannot charge the low
voltage battery using these terminals. Do not leave the low voltage power cables connected to the terminals for more than
30 seconds – remove from the vehicle's terminals as soon as the hood latches.
6. If you are using a variable power supply, set the supplied voltage to a value between 9V and 16.5V or between 30V and
50V.
7. Turn on the external power supply (refer to the manufacturer’s instructions). The latches are immediately released and you
can now open the powered frunk to access the front trunk area.
CAUTION: If you are using a variable power supply, do not change the supplied voltage while the cables are
connected.
8. Shut off the external power supply.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the external
power source is active may cause arcing.
9. Disconnect both cables, beginning with the black negative (-) cable.
10. Feed the terminals back into the cavity and then press the cover gently but firmly back into place to ensure that it is
secured.
1064
Owner's Manual
In Case of Emergency
Owner's Manual
1065
In Case of Emergency
Jump Starting
To jump start CybertruckModel SModel X, use an external power source that is capable of supplying at least 12V, such as a
portable jump starter or another vehicle.
CAUTION: When jump starting CybertruckModel SModel X, use jump cables that are 30 ft. (9 meters) or less in length.
Using cables that are longer than 30 ft. (9 meters) may result in damage to CybertruckModel SModel X or to the
external power source.
The steps below assume you are using an external low voltage power supply (such as a portable jump starter). If you are using
another vehicle to jump start CybertruckModel SModel X, follow the manufacturer's instructions.
WARNING: It may be more difficult to steer CybertruckModel SModel X when the vehicle is being supported by an
external low voltage power supply. The wheels may not be as responsive to the steering wheel as expected, and extreme
caution should be taken when repositioning CybertruckModel SModel X.
CAUTION: CybertruckModel SModel X uses a 48V low voltage architecture. As a result, some functions may be
unavailable or degraded if you are supporting CybertruckModel SModel X with less than 30V (for example, another
vehicle or a 12V portable jump starter).
CAUTION: Avoid using low voltage components of CybertruckModel SModel X (such as the climate control system,
cabin USB-C ports, lights, etc.) when the vehicle is being supported by an external low voltage power supply. Doing so
may disable low voltage systems and make it necessary to jump start CybertruckModel SModel X again.
CAUTION: CybertruckModel SModel X cannot be used to jump start another vehicle. Doing so can result in damage.
CAUTION: Avoid short circuits when jump starting CybertruckModel SModel X. Connecting cables to the wrong jump
post, touching leads together, etc., can damage CybertruckModel SModel X.
1. Open the powered frunk (see Opening the Powered Frunk with No Power on page 1062).
2. Remove the maintenance panel by pulling it upwards to release the trim clips that hold it in place.
3. Connect the external low voltage power supply’s red positive (+) cable to the horizontal jump post mounted next to the
brake fluid reservoir. The positive jump post is marked with a + sign.
1066
Owner's Manual
In Case of Emergency
CAUTION: To avoid damaging CybertruckModel SModel X, do not allow the positive cable to contact other metal
components.
4. Connect the external low voltage power supply’s black negative (-) cable to the vertical jump post. The negative jump post
is marked with a - sign. This jump post is used as a grounding location for the external support.
5. If you are using a variable power supply, set the supplied voltage to a value between 12V and 16.5V or between 30V and
50V.
6. Turn on the external power supply.
CAUTION: If you are using a variable power supply, do not change the supplied voltage while the cables are
connected. Doing so may cause damage to the vehicle.
7. Open the driver door and ensure that the touchscreen is on and the low voltage system is responsive. This may take up to
two minutes.
8. Ensure the touchscreen is on and that the low voltage system is responsive.
NOTE: If attempting to activate Transport Mode (to winch the vehicle onto a flatbed truck), leave the power supply
connected continuously until the vehicle has been secured. For more information, see Activate Transport Mode on page
1058.
Owner's Manual
1067
In Case of Emergency
9. Once external power is no longer required, shut off the external power supply.
WARNING: Shut off the external power supply before removing either cable. Removing the cables while the external
power source is active may cause arcing.
10. Disconnect both cables, beginning with the black negative (-) cable.
NOTE: CybertruckModel SModel X may not be able to shift into Drive until after the high voltage Battery has been charged
and the low voltage system is able to recover fully. See Running Out of Range on page 589.
11. Replace the maintenance panel by placing it back in its original location and pressing down until it is secure.
12. Close the powered frunk (see Closing on page 818).
Opening Doors with No Power
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: 2024.32_0824.pdf
Replacement Service Bulletin Number:
MFR Communication Date: 2024-08-31
MFR Internal Campaign ID/Software Version: 07/16/1905
Communication Type: Over The Air
NHTSA Components: UNKNOWN OR OTHER
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA AutoAuth: Now supports FCA SGW module for Chrysler, for Jeep, for Dodge (2018+), for Fiat (2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford, for Lincoln, and for Mazda ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order
- 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford, for Mazda, and for Lincoln. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase
- OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.