• When you use the mobile app to turn on the climate control system, it automatically turns off when the charge level drops
to 20%, or if two hours has passed. To cool or heat the cabin for a longer period of time, charge the vehicle and re-enable
your climate control preference through the mobile app.
• To reduce the temperature in the cabin in hot weather conditions, the fan may turn on to vent the cabin when the vehicle is
parked. This occurs only if the Battery's charge level is above 20%.
• In addition to cooling the interior, the air conditioning compressor also cools the Battery. Therefore, in hot weather, the air
conditioning compressor can turn on even if you turned it off. This is normal because the system’s priority is to cool the
Battery to ensure it stays within an optimum temperature range to support longevity and optimum performance.

1364

Owner's Manual

Climate
• Even when not in use, you may hear CybertruckModel SModel XModel 3Model Y emit a whining noise or the sound of
water circulating. These sounds are normal and occur when the internal cooling systems turn on to support various vehicle
functions, such as maintaining the low voltage battery and balancing the temperature of the high voltage Battery.
• In very humid conditions, it is normal for the windshield to fog slightly when you first turn on the air conditioning.
• It is normal for a small pool of water to form under CybertruckModel SModel XModel 3Model Y when parked. Extra water
produced by the dehumidifying process is drained underneath.
Tips:
• If the climate control system is louder than you prefer, manually reduce the fan speed.
• Improve the efficiency of the cabin heating or cooling by reducing your rate of acceleration. This allows the heat pump
system to take more heat from the Battery to efficiently heat the cabin, instead of maintaining the Battery's ability to
provide peak acceleration performance. Note that when subsequently increasing the acceleration mode, the Battery
requires time to warm up before the increased level of acceleration is available.
• To ensure the climate control system operates efficiently, close all windows and ensure that the exterior grille in front of the
windshield is free of ice, snow, leaves, and other debris.
• Your charge port latch may freeze in extremely cold weather or icy conditions. In cases where you cannot remove or insert
the charge cable, or your vehicle is not Supercharging due to the latch being frozen in place, enable Defrost Truck in the
mobile app. This helps thaw ice on the charge port latch so the charge cable can be removed or inserted. See Cold Weather
Best Practices on page 698 for more information.

Owner's Manual

1365

Climate
Adjusting the Front and Rear Vents
CybertruckModel SModel XModel 3Model Y has a unique horizontal face-level vent that spans the width of the dashboard. It
also has vents at the top and bottom of the rear console.
NOTE: Outside air is drawn into CybertruckModel SModel XModel 3Model Y through the grill in front of the windshield. Keep
the grill clear of obstructions, such as leaves and snow.
Using the front and rear touchscreens, you can pinpoint exactly where you want to direct the air flowing from this vent when
heating or cooling the cabin. When the face-level vent is on you can adjust the direction of the air flow from each vent. To
adjust the direction of the air flow, touch the radiating air waves from the corresponding vent on the touchscreen. The air flows
in a single stream when centered or splits into mirrored air streams when air is directed outward or inward from the center of
the vent.
NOTE: When you split a vent into two separate air flows, the air flow in each direction is not as strong as when all air is flowing
in a single direction.
Front passengers can turn off the flow of air from the passenger vent. To turn off air flow, press and hold the front passenger
air waves on the touchscreen. You can turn on the flow of air again by touching the front passenger vent.

Cabin Air Filter(s)
CybertruckModel SModel XModel 3Model Y has a HEPA filter to prevent pollen, industrial fallout, road dust and other
particles from entering through the vents.
NOTE: The HEPA filter requires periodic replacement. See Service Intervals on page 755.

1366

Owner's Manual

Climate
Cold Weather Best Practices
To ensure that CybertruckModel SModel XModel 3Model Y provides you with the best ownership experience possible in harsh
cold weather conditions, follow these best practices.

Before Driving
When snow and ice accumulate on your vehicle, moving parts, such as the door handlesdoors, windows, mirrors, and wipers
the wiper can freeze in place. To achieve maximum range and performance, it is helpful to warm the cabin and Battery before
driving. There are several ways to do so:
• Touch Controls > Schedule (also available on both the charging and climate control screens) to set a time when you want
your vehicle to be ready to drive (see Scheduled Precondition and Charge on page 748).
• In the mobile app, navigate to Climate to customize the temperature at which you want to heat the cabin. This also warms
the high voltage Battery as needed.
• In the mobile app, navigate to Climate > Defrost Car > Defrost to melt snow, ice, and frost on the windshield, charge port,
charge port (if equipped), windows, and mirrors. This also warms the high voltage Battery as needed.
NOTE: Tesla recommends activating climate settings at least 30-45 minutes before departure (see Operating Climate
Controls on page 673Operating Climate Controls on page 1360). Preconditioning times depend on outside temperature
and other factors. The mobile app will notify you once your vehicle has reached the desired preconditioning temperature.
Charge Port
If your charge port latch freezes in place and a charging cable becomes stuck in the charge port, try manually releasing the
charge cable. See Manually Releasing Charge Cable on page 742Manually Releasing Charge Cable on page 745Manually
Releasing Charge Cable on page 742Manually Releasing Charge Cable on page 1398.
In extremely cold weather or icy conditions, it is possible that your charge port latch may freeze in place. In these weather
conditions, on some vehicles, you can thaw ice on the charge port latch so the charge cable can be removed and inserted. To
do so, enable Defrost Car using the mobile app.
In extremely cold weather or icy conditions, it is possible that your charge port latch may freeze in place. In cases where you
cannot remove or insert the charge cable, or the vehicle is not Supercharging due to the latch being frozen in place, use the
Defrost Car setting in the mobile app. This can help thaw ice on the charge port latch so the charge cable can be removed or
inserted.
You can also prevent the occurrence of a charge port latch freezing in place by using the Schedule settings (see Scheduled
Precondition and Charge on page 748).
NOTE: If your charge port latch is frozen in place, it may not lock the charging cable in place when inserted, but it can still
charge at a slow AC rate even if the latch is not engaged.
Charging
By using Trip Planner (if available) to navigate to a Tesla charging location, CybertruckModel SModel XModel 3Model Y preheats the high voltage Battery to ensure when you arrive at the charger, the temperature of the Battery is optimal and ready to
charge. This reduces the amount of time it takes to charge. See (see Trip Planner on page 712).
NOTE: Tesla recommends using Trip Planner to navigate to a charging location for at least 30-45 minutes before arrival to
ensure optimal Battery temperature and charging conditions. If the drive to the charging location is less than 30-45 minutes,
consider preconditioning the Battery before driving (see Before Driving on page 698).
NOTE: The thermal system may produce steam under certain conditions for vehicles equipped with a heat pump (to determine
if your vehicle has a heat pump, touch Controls > Software > Additional Vehicle Information). For example, odorless steam can
come from the front of your vehicle while charging at a Supercharger in cold temperature. This is normal and not a cause for
concern.
Windows
In the mobile app, go to Climate and select Defrost CarDefrost Truck, which helps melt snow, ice, and frost on the windshield,
windows, and mirrors.
Owner's Manual

1367

Climate
In cold temperatures, CybertruckModel SModel XModel 3Model Y automatically makes a slight adjustment to the position of
the windows to make it easier to open doors.
NOTE: Always connect to an external, low voltage power supply before opening a door when the vehicle has no power to avoid
breaking a window.
Use the mobile app to schedule a service appointment for Tesla to provide hydrophobic coating to the side and rear windows
(not the front windshield) for a nominal fee.
Doors
In severe winter conditions, ice buildup can make it more difficult to open door handles. You can use the mobile app to pop
open the driver door in this situation.
1. In the mobile app, touch and hold any of the four quick control buttons and follow the instructions to customize quick
controls with Unlatch Door.
2. When you are next to your car, touch Unlatch Door to pop open the driver door.
Removing Ice From Door Handle

In severe winter conditions, ice buildup within the door handle can prevent the door handle from opening. The process for
freeing a CybertruckModel SModel XModel 3Model Y door handle is slightly different than others to remove ice buildup.
NOTE: Preemptively applying WD-40 to the door handle pivot pins can help prevent ice buildup inside your door handle.
CAUTION: Do not attempt to use tools or excessive force to release the door handle from ice buildup.
If your vehicle's door handles are black: Perform the following to remove ice from the door handle:

1. Forcefully press the frontmost part of the door handle. It will rock slightly inward to help break the ice.

1368

Owner's Manual

Climate

2. Press the rearmost part of the door handle to try to open as you normally would.
3. Once the door handle is able to move, open and close it a few more times to release any remaining ice buildup. Make sure
the door handle is fully pressed in (retracted) prior to entering the vehicle, and check that the door is fully closed before
driving away.
If your vehicle's door handles are silver: You can usually remove the ice with a few forceful bumps to the door handle using the
bottom of your fist. Perform the following to remove ice from the door handle:
CAUTION: Remove any jewelry or objects that can damage the paint prior to performing the procedure, and do not
attempt to use tools or excessive force.

1. Forcefully press the rearmost part of the door handle to try to open the door handle.
2. Working in a circular pattern around the perimeter of the door handle, use the bottom of your fist to forcefully bump the
door handle to break and release the ice buildup.

Owner's Manual

1369

Climate
3. Aiming for the rearmost end of the wide part of the door handle, use the bottom of your fist to forcefully bump the door
handle. Increase the intensity of the bumps as necessary, repeating steps 1 through 3 until the ice is removed and the door
handle can be opened.

CAUTION: Never bump the vehicle so hard as to cause a dent; the force used should be similar to knocking on your
neighbor’s front door.
4. Once the door handle is able to move, open and close it a few more times to release any remaining ice buildup. Make sure
the door handle is fully pressed in (retracted) prior to entering the vehicle, and check that the door is fully closed before
driving away.
Mirrors
If ice buildup is expected when parking, turn off Auto-Fold Mirrors. Touch Controls > Vehicle > Auto-Fold. Ice can prevent
exterior side mirrors from folding or unfolding.
NOTE: Side mirrors automatically heat as needed during preconditioning, or when the rear defroster is turned on.
Wipers
If you expect snow or ice to build up when parked, touch Controls > Service > Wiper Service Mode. This raises the wipers
against the windshield so they can defrost when the windshield defrosts (see Wipers and Washers on page 457). You can also
turn on wiper defrosters (if equipped). See Operating Climate Controls on page 673.
Tires and Tire Chains
Use winter tires to increase traction in snowy or icy conditions. You can purchase winter tires on the Tesla Shop (see Seasonal
Tire Types on page 775) (see Seasonal Tire Types on page 1429).
Tire chains provide additional traction when driving in snowy or icy conditions. Check local regulations to determine if tire
chains are recommended or required during winter months. See Using Tire Chains on page 775Tire Chains on page 1430 for
more information.
Your vehicle’s tire pressures will drop in cold ambient temperatures. If the TPMS indicator light appears, inflate the tires before
driving. The tires will lose one PSI for every 10° F (6° C) drop in outside temperature (see Tire Care and Maintenance on page
759Inspecting and Maintaining Tires on page 1428). Proper tire pressures help protect tires from potholes and improve range
when properly inflated.

While Driving
Cold weather can increase energy consumption because more power is required for driving, cabin and Battery heating. Follow
these suggestions to reduce energy consumption:

1370

Owner's Manual

Climate
• Use seat heaters to keep warm. Seat heaters use less energy than the cabin heater. Lowering the cabin temperature and
using seat heaters reduces energy consumption (see Operating Climate Controls on page 673Operating Climate Controls
on page 1360).
• Slow down your driving and avoid frequent and rapid acceleration.
• Turn on Range Mode to automatically limit the power that the climate control system uses to maintain the temperature of
the Battery and the cabin area. Range Mode also turns off signature lights (if equipped) and adjusts the front and rear
motor torque split to maximize range (see Getting Maximum Range on page 750).
• If your vehicle is equipped with a heat pump (to determine if your vehicle has a heat pump, touch Controls > Software >
Additional Vehicle Information), you can improve the efficiency of the cabin heating by reducing your selected acceleration
mode (see Acceleration Modes on page 500). This allows the heat pump system to take more heat from the Battery to
efficiently heat the cabin, instead of maintaining the Battery's ability to provide peak acceleration performance. This helps
to maximize driving efficiency in colder weather. Note that when subsequently increasing the acceleration mode, the
Battery requires time to warm up before the increased level of acceleration is available.
• You can improve the efficiency of the cabin heating by reducing your selected acceleration mode (see Acceleration Modes
on page 500Acceleration Modes on page 504). This allows the heat pump system to take more heat from the Battery to
efficiently heat the cabin, instead of maintaining the Battery's ability to provide peak acceleration performance. This helps
to maximize driving efficiency in colder weather. Note that when subsequently increasing the acceleration mode, the
Battery requires time to warm up before the increased level of acceleration is available.
Regenerative Braking
Regenerative braking can be limited if the Battery is too cold. As you continue to drive, the Battery warms up and regenerative
power increases (see Regenerative Braking on page 467Regenerative Braking on page 1249).
NOTE: Limited regenerative braking can be avoided if you allow enough time to precondition your vehicle or if you use
Schedule to precondition CybertruckModel SModel XModel 3Model Y before your departure time (see Scheduled
Precondition and Charge on page 748).
NOTE: Installing winter tires can result in temporarily reduced regenerative braking power but after a short period of driving,
CybertruckModel SModel XModel 3Model Y recalibrates to correct this. Touch Service > Wheel & Tire > Tires to select winter
tires and quicken this process.
Cold Battery
A blue snowflake icon appears on your instrument paneltouchscreen when some of the stored energy in the Battery is
unavailable because the Battery is cold. This portion of unavailable energy displays in blue on the Battery meter.
Regenerative braking, acceleration, and charging rates may be limited. The snowflake icon no longer displays when
the Battery is sufficiently warm.

After Driving
Leave CybertruckModel SModel XModel 3Model Y plugged in when not in use. This uses the charging system, rather than the
Battery itself, to keep the Battery warm (see High Voltage Battery Information on page 729).
Scheduled Precondition
When parked, use the Controls > Schedule settings, available on both the charging and climate control screens, to set a time
when you want to precondition CybertruckModel SModel XModel 3Model Y (see Scheduled Precondition and Charge on page
748). You can also use Schedule to prevent the charge port latch freezing in place. Your vehicle determines the appropriate
time to begin preconditioning so that cabin and Battery are warm by your planned departure time.
Tesla recommends that you also schedule a charge with your precondition to ensure that your vehicle has sufficient energy for
the trip. When CybertruckModel SModel XModel 3Model Y is not plugged in, preconditioning operates but only when the
Battery's charge level is above 20%.

Storage
If you leave CybertruckModel SModel XModel 3Model Y parked for an extended period of time, plug the vehicle into a charger
to prevent normal range loss and to keep the Battery at an optimal temperature. Your vehicle is safe to stay plugged in for any
length of time.

Owner's Manual

1371

Climate
When not in use, CybertruckModel SModel XModel 3Model Y enters a sleep mode to conserve energy. Reduce the number of
times you check your vehicle’s status on the mobile app, as this automatically wakes up your vehicle and starts normal energy
consumption.

1372

Owner's Manual

Climate
Hot Weather Best Practices
To ensure that CybertruckModel SModel XModel 3Model Y provides you with the best ownership experience possible in hot
ambient conditions, follow these best practices.

Before Driving
There are several ways to prepare your vehicle for a drive, without having to get into an already hot vehicle:
• Precondition the cabin by moving the direction of air flow from the vents, and turn the seat heaters on or off. In the mobile
app, navigate to Climate to customize the temperature at which you want to cool the cabin.
• Touch Schedule, available on both the Charging and Climate Control screens, to set a time when you want your vehicle to
be ready to drive (see Scheduled Precondition and Charge on page 748).
• Enable Cabin Overheat Protection, which prevents the cabin from getting too warm in hot ambient conditions. You can
choose whether you want the A/C or just the fan to run when the temperature in the cabin exceeds 105° F (40° C) or the
selected temperature (if available).
• In the mobile app, navigate to Controls to vent the windows.
NOTE: Tesla recommends activating climate settings at least 30-45 minutes before departure (see Operating Climate Controls
on page 673Operating Climate Controls on page 1360). Preconditioning times depend on outside temperature and other
factors. The mobile app will notify you once your vehicle has reached the desired preconditioning temperature.

After Driving
Leave CybertruckModel SModel XModel 3Model Y plugged in when not in use, especially if using Preconditioning or Cabin
Overheat Protection. This uses the charging system, rather than the battery itself, to maintain a comfortable temperature (see
High Voltage Battery Information on page 729). In addition, there are several ways to minimize a hot cabin:
• Before leaving your vehicle (to run errands, for example), use Dog Mode to keep the cabin cool for pets or perishable
goods. See Keep Climate On, Dog, and Camp on page 682Keep Climate On, Dog, and Camp on page 1363 for more
information.
• Tesla recommends turning the air conditioning off approximately 30 seconds before pressing Park to reduce puddling
below the vehicle.
• Park in the shade to help reduce power consumption and maintain cooler cabin temperatures.
• Use a sun shade (available on the Tesla Shop) if you have to park outside in the sun.
• When parked, plug in CybertruckModel SModel XModel 3Model Y and Schedule your charging. Your vehicle determines
the appropriate time to begin charging so it is complete during off-peak hours. The cabin and Battery are also prepared by
your set departure time. For more information, see Scheduled Precondition and Charge on page 748.

Charging
When using Trip Planner or navigating to a Supercharger station, your vehicle automatically prepares the Battery for most
efficient charging. In extreme heat, you may not see the message that the vehicle is preconditioning the Battery while
navigating to a Supercharger, but it is still preparing the Battery for charging.
NOTE: Tesla recommends using Trip Planner to navigate to a charging location for at least 30-45 minutes before arrival to
ensure optimal Battery temperature and charging conditions. If the drive to the charging location is less than 30-45 minutes,
consider preconditioning the Battery before driving (see Before Driving on page 698).
If possible, leave your vehicle plugged into a charger whenever not in use, even in warm weather, especially if using
Preconditioning or Cabin Overheat Protection.

Storage
If you leave CybertruckModel SModel XModel 3Model Y parked for an extended period of time, plug the vehicle into a charger
to prevent normal range loss and to keep the Battery at an optimal temperature. Your vehicle is safe to stay plugged in for any
length of time.

Owner's Manual

1373

Climate
When not in use, CybertruckModel SModel XModel 3Model Y enters a sleep mode to conserve energy. Reduce the number of
times you check your vehicle’s status on the mobile app, as this automatically wakes up your vehicle and starts normal energy
consumption.

1374

Owner's Manual

Navigation and Entertainment
Maps and Navigation
Map Overview
The touchscreen displays a map at all times (except when CybertruckModel SModel XModel 3Model Y is shifted into
Reverse).
Use your finger(s) to interact with the map:
• To move the map in any direction, hold and drag a finger.
• To rotate the map in any direction, hold and turn two fingers.
• To zoom the map in or out, expand or pinch two fingers, respectively.
NOTE: When you rotate or move the map, your current location is no longer tracked. The message "Tracking Disabled" displays
briefly next to the map orientation icon and the icon turns gray. To re-enable tracking, touch the map's orientation icon and
choose North Up or Heading Up.
NOTE: The map zooms in and out automatically when a navigation route is active.
To change the orientation of the map, toggle between these options:
North Up: North is always at the top of the screen.

Heading Up: The direction you are driving is always at the top of the screen. The map rotates as you change
direction. This icon has an integrated compass that indicates the direction you are driving.
NOTE: Touching this icon while navigating to a destination displays the route overview.

Route overview is available when you are navigating to a destination and displays when you expand the turnby-turn direction list (by swiping it downward). When you collapse the turn-by-turn direction list by swiping it
upward, the map displays your previously chosen orientation.

Map Display
When CybertruckModel SModel XModel 3Model Y is in Park, the following icons display on the map to allow you to customize
the type of information the map displays. To access these icons when driving, touch anywhere on the map (they disappear
after a few seconds).
Satellite imagery (if equipped with premium connectivity).

Traffic conditions (if equipped with premium connectivity).

Owner's Manual

1375

Navigation and Entertainment
Map details (such as points of interest).

Drop a pin anywhere on the map by pressing and holding your finger on a desired location. When you drop a pin, or touch an
existing pin, the chosen location is centered on the map and a popup screen provides information about the location. From this
popup, you can navigate to the location add or remove the location from your list of favorite destinations (see Home, Work,
and Favorite Destinations on page 709).

Charging locations. Shows a popup list that includes the city and proximity of the corresponding stations on the
map. Charging locations include Tesla Superchargers, destination charging sites, third-party fast chargers, and
public chargers that you have used previously. See Charging Locations on page 709. Touch the lightning bolt
icons in the popup list to filter by the types of chargers based on max power.
NOTE: In some market regions, third-party fast chargers are also included on the map as dark gray pins when
you display chargers.

Navigation Settings
NOTE: The navigation settings available can vary depending on region and vehicle configuration.
The navigation settings icon displays when you touch ... once you start navigating to a destination.
NOTE: You can also access navigation settings by touching Controls > Navigation.

Touch the navigation settings icon to customize the navigation system to suit your preferences (the available settings vary
depending on your market region and vehicle configuration):
• Navigation Guidance: Touch Voice to enable an audible reading for navigation instructions.
• Touch - or + to increase or decrease the volume of spoken navigation instructions. Decreasing all the way to the left or
touching the speaker icon mutes the instructions. You can also mute/unmute navigation instructions by touching the
speaker icon. This volume setting applies only to the navigation system's spoken instructions. Volume for Media Player and
Phone does not change.
NOTE: Volume may automatically be adjusted based on driving speed and climate settings.
NOTE: Navigation instructions are muted when the paired phone has an ongoing phone call.
• Enable Automatic Navigation if you want CybertruckModel SModel XModel 3Model Y to automatically initiate a navigation
destination when you get in your vehicle. Destinations are predicted based on commonly driven routes, time of day, and
calendar entries (see Automatic Navigation on page 708).
• Enable Trip Planner (if available in your market region) to add Supercharger stops as needed. Supercharging stops are
added to navigation routes with the goal of minimizing the amount of time you spend driving and charging (see Trip Planner
on page 712).
• Enable Online Routing to automatically route to avoid heavy traffic and to get real-time traffic conditions along navigation
routes, if available in your region (see Online Routing on page 711).
• Touch Avoid Ferries to be automatically routed to avoid ferries.
• Touch Avoid Tolls to be automatically routed to avoid tolls, if possible.
• Touch Use HOV Lanes to include High Occupancy Vehicle (HOV) lanes on navigation routes. This is particularly useful when
using Navigate on Autopilot (see Navigate on Autopilot on page 595Navigate on Autopilot on page 563).

1376

Owner's Manual

Navigation and Entertainment
Navigating to a Destination
To navigate to a location, touch the search bar in the corner of the map and enter a destination, send the destination from your
phone, or use voice commands (see Voice Commands on page 97) for an address, landmark, business, etc. If the destination
you choose has other destinations within it (such as terminals at an airport), you can also choose a sub-destination.
Touch the search bar for different options:
• Refresh a search when you zoom in or drag to a different area of the map by tapping Search this area when prompted (if
available in your region).
• Choose a saved Home or Work location (see Home, Work, and Favorite Destinations on page 709).
• Select a Charging destination (see Charging Locations on page 709).
• Pick from Recent destination (the most recent destination is listed at the top).
• Choose a destination you have marked as a Favorite (see Home, Work, and Favorite Destinations on page 709).
• A popular restaurant when you're feeling Hungry or a popular destination (such as museums and amusement parks) when
you're feeling Lucky (see Lucky and Hungry on page 709).
NOTE: You can start navigation remotely from your IOS® or Android™ device using the "share" functionality on your device
after allowing access to the Tesla mobile app.
When you specify a location, the touchscreen zooms out to provide an overview of the route you need to travel and displays a
turn-by-turn direction list. Estimated arrival time, driving time, and mileage displays at the bottom of the direction list. Note
the following about the turn-by-turn direction list:
• The Battery icon on the turn list provides a visual representation showing an estimate of how much energy will remain when
you reach your destination, and how much will remain if you make a round trip back to your current location. See Predicting
Energy Usage on page 711.
• If charging is needed to reach your destination and Trip Planner is enabled (and available in your market region), the
navigation route automatically includes Supercharger stops (see Trip Planner on page 712).
• If you won't have enough energy to reach your destination and there is no Supercharger on the route, an alert tells you that
charging is needed to reach your destination.
• Each turn is preceded by the distance to the maneuver.
• To see the bottom of the list, you may need to drag the list upward.
• Touch the top of the list to minimize it.
While navigating, the map tracks your location and displays the current leg of your trip. You can display the entire route at any
time by swiping down to expand the turn-by-turn direction list or touching the route overview icon.
Below the turn-by-turn list, a progress bar shows how close you are to your destination or next stop. If online routing is
enabled, the progress bar also shows live traffic conditions on your route (see Online Routing on page 711).
To stop navigating, touch Cancel, located in the bottom corner of the turn-by-turn direction list. Swipe right on the suggested
location or press and hold the location to quickly delete certain recent navigation searches.
NOTE: If a data connection is not available, onboard maps allow you to navigate to any destination, but you must enter the
exact and complete address.

Owner's Manual

1377

Navigation and Entertainment
If Navigate on Autopilot is enabled, you can turn it on for the navigation route by touching Navigate
on Autopilot in the turn-by-turn direction list (when the feature is active, the icon is blue). Navigate
on Autopilot automatically changes lanes and steers CybertruckModel SModel XModel 3Model Y
on controlled-access roads (like highways and freeways), along a navigation route. For details, see
Navigate on Autopilot on page 595Navigate on Autopilot on page 563.

Selecting an Alternate Route
Depending on market region and vehicle configuration, this feature may not be available on your vehicle. Your vehicle must be
equipped with Premium Connectivity.
After you have entered a destination with one stop, the map displays up to three alternate routes. This allows you to easily
compare total travel time and traffic information for each route. If you do not select a preferred route within the timeout
period, the fastest route is automatically selected.
r
Adding Stops to a Route
After entering a destination, edit your route by adding, deleting or reordering stops. Touch the three dots at the bottom of the
turn-by-turn direction list to view options to edit your route.
Add Stop allows you to add a stop by searching for a location or adding a Home, Recent or Favorite destination.
You can also add a stop by touching any pin on the map and selecting Add from the popup.

Edit Stop allows you to set up a complex trip by adding or deleting stops on your route. Drag and drop stops by
touching the equal sign to reorder your trip.

You can also use the Tesla mobile app to edit your route (if available in your region). In the Tesla mobile app, go to Locations >
Navigate and enter a destination, touch Edit Trip > Add Stop to edit your route, then touch Send to Car to share the trip with
your vehicle.
NOTE: Requires Tesla mobile app version 4.27.5 or newer.
Automatic Navigation
NOTE: Automatic Navigation may not be available in all market regions and on all vehicle configurations.
Automatic Navigation can predict a destination when you get in your vehicle. When your phone's calendar is synced to
CybertruckModel SModel XModel 3Model Y, and the calendar includes an event that takes place within two hours of when
you get in your vehicle to drive, Automatic Navigation suggests the location of the event (assuming a valid address is
associated with the event).
In addition, if you are Home and drive on weekdays (Monday to Friday) from 5:00 AM to 11:00 AM, Automatic Navigation can
automatically route you to your specified Work location (see Home, Work, and Favorite Destinations on page 709). Likewise, if
you are at work on weekdays from 3:00 PM to 11:00 PM, Automatic Navigation can automatically route you to your specified
Home location.

1378

Owner's Manual

Navigation and Entertainment
To enable Automatic Navigation, touch Controls > Navigation > Automatic Navigation. You must have your phone's calendar
synced to CybertruckModel SModel XModel 3Model Y and the event must include a uniquely specified and valid address (see
Phone, Calendar, and Web Conferencing on page 365).
NOTE: Navigation instructions that you enter manually, or send to CybertruckModel SModel XModel 3Model Y, override
routes suggested by Automatic Navigation.

Lucky and Hungry
NOTE: Features may not be available in all market regions and on all vehicle configurations.
In addition to navigating to a destination of your choice, CybertruckModel SModel XModel 3Model Y can also suggest nearby
locations based on whether you are feeling Hungry or Lucky. In the navigation search bar, touch Hungry or Lucky. Hungry
suggests a list of popular restaurants, whereas Lucky suggests a list of popular destinations (such as museums and
amusement parks). Once you discover an interesting destination, touch Navigate to proceed to the destination.
This feature requires the latest version of Navigation maps. To download, connect CybertruckModel SModel XModel 3Model
Y to Wi-Fi and touch Controls > Software to check if an update is available (see Map Updates on page 712).

Home, Work, and Favorite Destinations
If you frequently drive to a destination, add it as a favorite to avoid entering the location's name or address each time. When
you add a destination as a Favorite, you can easily navigate to it by touching the navigation search bar and then touching
Favorites and choosing it from your list of favorite destinations.
To add a destination to your Favorites list, touch its pin on the map, then touch the star icon on the popup
screen that appears. Enter a name (or leave as-is to accept the default name), then touch Add to Favorites. The
star becomes solid and the destination is included on your Favorites list.

To delete a Recent or Favorite destination, touch it on the destination list and hold it down briefly until the X appears. Then
touch the X to delete it from the list.
Home and Work locations also display under the navigation search bar. Touch to set an address to the corresponding location.
After entering the address, touch Save as Home or Save as Work. Then simply touch these shortcuts whenever you want to
navigate home or to work.
To change or delete the corresponding address, press and hold the Home or Work icon. A popup allows you to enter a new
address and Save as Home or Save as Work. Once a Home or Work location is saved, CybertruckModel SModel XModel
3Model Y may prompt you to navigate to your Work location in the mornings and to your Home location in the evenings and
provide an estimated driving time based on current traffic conditions. See Automatic Navigation on page 708. Touch Clear
Home or Clear Work to remove associated addresses entirely. Based on your usage patterns,
CybertruckModel SModel XModel 3Model Y may prompt you to save a location as Home or Work.
For security reasons, if you sell , transfer ownership, or allow others to drive CybertruckModel SModel XModel 3Model Y, it is
recommended that you delete your Home and Work locations. You can delete these individually or you can perform a factory
reset to erase all personal data (touch Controls > Service > Factory Reset).

Charging Locations
To display charging locations on the map, touch the map's search bar, then touch Charging. Charging locations are shown in a
list (with the closest charging location at the top of the list) and represented by corresponding pins on the map. Touch a pin to
display more information, navigate to, or mark it as a favorite.
Touch the lightning bolt icons to specify the types of charging locations you want the map to include (by default, the map
displays only Superchargers):

Owner's Manual

1379

Navigation and Entertainment
Touch to include low power stations up to
25 kW, such as destination charging
locations.

Touch to include low power
stations up to 70 kW, such as
destination charging locations.

Touch to include low power
stations up to 70 kW, such as
destination charging locations.

Touch to include high power
chargers above 70 kW.

Touch to include high power
chargers above 70 kW.

Touch to include medium power chargers
25 kW to 75 kW.

Touch to include high power chargers 75
kW and above.

NOTE: In some market regions, third-party fast chargers are also included as dark gray pins when you choose to display all
charging stations.
The appearance of a charging location's pin reveals the predicted status about the location. Touch the pin to display details.
The Supercharger location is operational and the number displayed on the pin represents the predicted number
of available Supercharger stalls upon arrival.
NOTE: A Supercharger located on your current navigation route is colored black (or white, if the touchscreen is
in night mode).
The Supercharger location is predicting a high volume of users. You may need to wait before charging.

The Supercharger location may be operating at a reduced capacity.

The Supercharger location may be closed.

The Supercharger location has no data available but should be operational.

The location is either a destination charging location, a third-party fast charger, or a public charging station that
you have previously used. Touch to display more information such as usage restrictions and available charge
current.
NOTE: When the map is zoomed out and more than one destination charging location is available in an area, the
pin is round and displays the number of stations. Touch the pin to zoom in. Then you can touch an individual pin
for details about a specific location.
Touch a charging location's pin to display a popup from which you can:
• Determine it's exact location and approximate distance from your current location.

1380

Owner's Manual

Navigation and Entertainment
• View amenities that are available at the charging location, including restrooms, restaurants, lodging, shopping, and Wi-Fi.
On a Supercharger popup, touch an amenity icon to search the surrounding area for the associated amenity.
• Touch the arrow icon to navigate to the charging location.
NOTE: When navigating to a Supercharger (or third-party fast charger in some regions), CybertruckModel SModel XModel
3Model Y preconditions the Battery to prepare for charging. This ensures you arrive with an optimal Battery temperature,
reducing the amount of time it takes to charge. In some circumstances (such as cold weather), it is normal for the motor(s)