NHTSA ID Number: 11006911
Manufacturer Communication Number: fsd_12-5-1-2_082024.pdf
TSB/Document Date: 2024-09-04
Summary
Tesla
does not provide physical owner's manual copies. Instead, all available owner’s manual content is integrated into the vehicle software, and only the content relevant for a given vehicle, based on vehicle configuration and software version installed, is displayed on its touchscreen. This file contains all available owner’s manual content for the vehicle converted to PDF format, and given the distribution method and NHTSA’s submission format requirements, it is the best available representative copy of owner’s manual content. However, a customer who accesses the owner’s manual via their vehicle’s touchscreen would only see the parts of this PDF file that are relevant to their vehicle.
possible to pull 20A from the cabin and 20A from the cargo bed at the same time. All AC power outlets combined (120V cabin,
120V cargo bed, and the 240V cargo bed outlet) are limited to a combined maximum of 40A. If multiple devices are plugged in
and drawing power at the same time, power to each device may be reduced or interrupted.
The outlets stop providing power when Model SModel XModel 3Model Y is no longer occupied (when you leave the vehicle
and close the doors).
To enable power to the outlets, touch Controls > Outlets & Mods on the touchscreen. From here you can toggle power to all
AC outlets and each power feed (see Connecting Accessories to the 48V Power Feeds on page 1399). While the outlets are
supplying power, the touchscreen shows the amount of power being used.
You can also enable power to the outlets and power feeds using the mobile app.
NOTE: Leaving a device plugged in depletes the high voltage Battery
. Even if nothing is plugged in, the outlets draw small
amounts of power from the Battery whenever they are enabled. When the charge level of the high voltage Battery
is very low,
power to the outlets shuts off and a message is displayed on the touchscreen. Leaving a device plugged in does not deplete
the low voltage battery.
CAUTION: Do not use the AC outlets to power a device with a power rating that exceeds the limits listed above.
1112
Owner's Manual
Overview
Keep On Cabin and Bed Outlets
If you want the outlets to continue supplying power even when the vehicle is not occupied, touch Controls > Outlets & Mods
and enable Keep On Cabin and Bed Outlets. After 12 hours, or once the high voltage Battery
has less than 5% remaining
energy, the outlets shut off. Keep On Cabin and Bed Outlets is automatically enabled whenever you turn on the outlets using
the mobile app.
CyberTent Mode
After installing the CyberTent, enable CyberTent Mode for optimal comfort. CyberTent Mode:
• Levels the suspension.
• Opens the tonneau cover and keeps it open by disabling the switches.
• Displays controls to adjust the front and rear lights.
• Allows outlets to be kept on indefinitely.
NOTE: Using CyberTent Mode and keeping the outlets or lights on may increase power usage.
• Disables walk-away lock.
NOTE: It is your responsibility to ensure the vehicle is appropriately locked or attended to at all times.
To enable, touch Controls > Outlets & Mods > CyberTent Mode. Model SModel XModel 3Model Y cannot be driven while
CyberTent Mode is enabled.
Overload Capability
The AC outlets on Model SModel XModel 3Model Y are all capable of providing additional surge current to start almost all
devices (such as power tools, motors, and compressors) up to 110LRA.
Troubleshooting AC Outlets
AC outlets may be disabled in the following scenarios:
• Very low ambient temperatures.
• When an AC charging cable is connected to Model SModel XModel 3Model Y even if the vehicle is not actively charging.
• The high voltage Battery
does not have enough charge.
• GFCI or overcurrent detection has been tripped.
If one or more outlets unexpectedly stops providing power, first ensure that you have enabled power to the outlets (touch
Controls > Outlets & Mods) and that the high voltage Battery
has enough remaining charge.
Each power outlet in Model SModel XModel 3Model Y is equipped with overcurrent detection and a ground fault circuit
interrupter (GFCI), which interrupts the power supply to an outlet if an issue is detected, such as a current leakage. In this
case, the outlets will turn off. Overcurrent detection may happen if multiple devices plugged in at once draw too much power
from the AC power outlets.
CAUTION: Use only "UL" Listed devices with the AC power outlets in Model SModel XModel 3Model Y.
CAUTION: Damage to a device or data loss (such as from a laptop or external drive) due to a sudden loss of power is not
covered by the warranty.
If an outlet is still not providing power, the GFCI or overcurrent detection may have been tripped. When an outlet is faulted, an
option to reset the outlets becomes available. To reset:
1. Disconnect all devices from all AC outlets (three outlets in the cargo bed and two in the center console).
2. Touch Controls > Outlets & Mods > Reset.
3. Reconnect devices and re-enable power to the outlets by touching Controls > Outlets & Mods > AC Outlets.
Owner's Manual
1113
Overview
NOTE: Power to AC outlets is still available when Model SModel XModel 3Model Y is DC charging (while Supercharging, for
example). See Charging Instructions on page 1346.
Warnings and Cautions
CAUTION: Always check each outlet for damage before use.
CAUTION: Keep the outlet cover closed when the cargo bed outlets are not in use.
CAUTION: Keep the outlet cover closed when Cybertruck is AC charging, especially in wet weather. AC charging may be
disabled if moisture enters one of the outlets.
CAUTION: Damage to Model SModel XModel 3Model Y caused by an external device that is plugged in to an outlet is
not covered by the warranty.
CAUTION: Use caution when driving Model SModel XModel 3Model Y while devices are plugged into the cargo bed
outlets. Ensure that all objects in the cargo bed are properly secured (see Securing Cargo on page 1175).
WARNING: A power outlet and a device's plug can become hot. Use caution when unplugging a device.
WARNING: Do not insert any objects into the outlets other than electrical plugs. Treat the outlets on
Model SModel XModel 3Model Y the same as you would any other outlet, and take care to ensure proper handling.
Misusing outlets can cause serious injury.
WARNING: Protect the cargo bed outlets from moisture, water, and foreign objects at all times. If you see a foreign
object in an outlet, or if the outlets appear corroded or damaged, do not use them.
WARNING: Do not use the cargo bed outlets if they are wet or covered in snow.
WARNING: If rain falls while an accessory is plugged in and drawing power from the cargo bed outlets, do not allow rain
water to run along the length of charge cable, causing the outlets to become wet.
WARNING: Do not connect a power source (such as a solar panel or external battery) to a cargo bed outlet.
WARNING: As with any power outlet, do not leave children unattended near the cargo bed outlets and ensure the outlet
cover is closed when the outlets are not in use.
1114
Owner's Manual
Overview
Voice Commands
NOTE: For your convenience, Tesla
allows you to choose from a variety of languages to use for voice commands. To choose a
different language, touch Controls > Display > Voice Recognition Language.
Use voice commands to easily control settings and preferences without using the touchscreen. Voice commands are designed
to understand natural requests. The following is a non-exhaustive list of actions that you can perform with voice commands:
• Adjust climate preferences
• Tweak the windshield wiper speed and frequency
• Control various aspects of your vehicle
• Navigate to a location
• Call a contact
• Interact with apps and settings
To initiate a voice command, press and release the right scroll wheel button on the steering wheelsteering yoke (or steering
wheel)press and release the right scroll wheel button on the steering wheelsteering yoke (or steering wheel)fully press the
microphone button on the right side of the steering wheelsteering yoke (or steering wheel)fully press the microphone button
on the right side of the steering wheelsteering yoke (or steering wheel)touch the voice button on the right side of the steering
wheelsteering yoke (or steering wheel). When a chime sounds, make your request.
Owner's Manual
1115
Overview
1116
Owner's Manual
Overview
Examples of Voice Commands
Here is a list of example voice commands. This is not an exhaustive list. Tesla
is constantly working to improve voice
commands.
NOTE: Your vehicle must be in Park to enable some voice commands (such as Sentry Mode, Dog Mode, etc.).
Climate Controls
Adjust your climate preferences:
• "Make it cooler"
• "Make it warmer"
• "Turn on/off the driver's seat heater"
• "Cool down the passenger"
• "Direct airflow to my face"
• "Sync climate"
• "Increase/decrease the fan speed"
• "Turn on/off rear defroster"
• "Set the temperature/fan..."
• "Turn on recirculate"
Windshield Wipers
Update the windshield wiper speed and frequency based on changing road and weather conditions:
• "Speed up the wipers"
• "Increase/decrease windshield wiper speed by..."
• "Turn on/off the wipers"
Vehicle Controls
Modify various controls in your vehicle:
Owner's Manual
1117
Overview
• "Sentry Mode on/off"
• "Keep my car safe"
• "Lock/unlock the doors"
• "Turn on Dog Mode"
• "Fold/unfold the mirrors"
• "Open/close charge port"
• "Start/stop charging"
• "Open service settings"
• "Open the glovebox"
Navigation
Search for or navigate to a location:
• "Where is [location]?"
• "Drive to [location]"
• "Navigate to [location]"
• "Show nearby Superchargers"
• "I'm feeling hungry/lucky" (see Maps and Navigation on page 690).
• "Stop navigation"
• "Mute voice guidance"
If you have defined a navigation address for your home or work locations, you can use a voice command to navigate there by
saying "Navigate home" or "Take me to work".
Contacts
To call or text a contact on your Bluetooth-connected phone (see Phone, Calendar, and Web Conferencing on page 362), say:
• "Call [contact name/phone number]"
• "Text [contact name/phone number]"
Media
Listen to media and adjust your playback preferences:
• "Listen to [song name]"
• "Lower/raise the volume"
• "Skip to next"
• "Pause/play song"
• "Change the source to [media source]"
To improve voice command recognition accuracy, provide multiple cues in your command, such as artist and song.
Apps and Settings
Easily navigate through your apps and settings:
• "Open [Toybox/browser/theater/phone]"
• "Search for..."
• "The screen is too bright"
• "Show me the Owner's Manual"
1118
Owner's Manual
Overview
You can also file a bug report by saying "Report" , "Feedback", or "Bug report".
For more information on voice commands, go to https://www.tesla.com/support/voice-commands.
NOTE: To support ongoing quality improvements, Tesla
captures and processes voice command transcriptions (such as “set
the temperature…”). Audio voice recordings are not collected, and transcriptions are not associated with your Tesla
account or
with your vehicle's identification number. To further protect your privacy, voice commands containing personal data are not
captured (such as "Navigate to..." or "Make a call to...").
Cameras
Your Model SModel XModel 3Model Y includes the following components that actively monitor the surrounding area:
1. A camera is mounted on the tailgate.
2. A camera is mounted in each door pillar.
3. Two cameras are mounted to the windshield above the rear view mirror.
4. A camera is mounted above each front wheel.
5. A camera is mounted above the grille on the front bumper.
Viewing Camera Feeds
The Camera app shows the views from the side cameras, rear-facing camera, and front-facing camera. To open the Camera
app, you can either:
• Open the app launcher and touch the Camera app.
• Touch the camera icon on the right side of the steering wheel.
Owner's Manual
1119
Overview
Swipe up or down to switch between the rear and front camera views.
The camera app opens automatically when you shift into Reverse.
Rear-Facing Camera
Model SModel XModel 3Model Y is equipped with a rear-facing camera mounted on the tailgate.
Whenever you shift into Reverse, the touchscreen displays the view from the rear-facing camera. Lines show your driving path
based on the position of the steering wheel. These lines adjust as you move the steering wheel. The tailgate must be fully
closed in order to see the rear view and lines on the display.
You can choose to always show the rear view camera feed when the tonneau cover is closed by touching Controls > Display >
Rear View Camera > Auto.
If a black screen appears on the touchscreen instead of the rear view camera feed when in Reverse, use the rear view mirrors
and ensure your surroundings are safe before continuing to Reverse. If inoperability of the rear view camera persists, try
restarting the touchscreen (see Restarting the Touchscreen on page 1096). If the camera feed still shows as a black screen
after that, use the mobile app to schedule a service appointment.
1120
Owner's Manual
Overview
WARNING: Never depend on the cameras to inform you if the area around you is free of objects and/or people. The
cameras may not detect objects or barriers that can potentially cause damage or injury. In addition, several external
factors can reduce the performance of the cameras, including a dirty or obstructed lens. Therefore, depending on the
cameras to determine if Model SModel XModel 3Model Y is approaching an obstruction can result in damage to the
vehicle and/or objects and can potentially cause serious injury. Always inspect the area with your own eyes. When
reversing, perform shoulder checks and use all mirrors. Use the cameras for guidance purposes only. It is not intended
to replace your own direct visual checks and is not a substitute for careful driving.
Front-Facing Camera
Your Model SModel XModel 3Model Y is equipped with a front-facing camera located above the grille on the front fascia.
To display the view from the front-facing camera at any time, open the app launcher and touch the Camera app or touch the
camera icon on the right side of the steering wheel. Swipe up or down to switch betweeen the rear, front, and side camera
views.
WARNING: Never depend on the camera to inform you if the area around you is free of objects and/or people. The
camera may not detect objects or barriers that can potentially cause damage or injury. In addition, several external
factors can reduce the performance of the cameras, including a dirty or obstructed lens. Therefore, depending on the
cameras to determine if Model SModel XModel 3Model Y is approaching an obstruction can result in damage to the
vehicle and/or objects and can potentially cause serious injury. Always inspect the area with your own eyes. Use the
camera for guidance purposes only. It is not intended to replace your own direct visual checks and is not a substitute for
careful driving.
Cabin Camera
Your Model SModel XModel 3Model Y is equipped with a cabin camera located above the rear view mirror.
Owner's Manual
1121
Overview
The cabin camera can determine driver inattentiveness and enhances active safety features (such as Forward Collision
Warning). You can also view the feed from this camera in the Tesla mobile app when Sentry Mode Live Camera is enabled (see
Sentry Mode on page 655).
Data Sharing
By default, images and video from the camera do not leave the vehicle itself and are not transmitted to anyone, including Tesla,
unless you enable data sharing. If you enable data sharing and a safety critical event occurs (such as a collision),
Model SModel XModel 3Model Y shares short cabin camera video clips with Tesla to help us develop future safety
enhancements and continuously improve the intelligence of features that rely on the cabin camera. Data may also be shared if
diagnostics are required on cabin camera functionality. Cabin camera does not perform facial recognition or any other method
of identity verification. To protect your privacy, cabin camera data is not associated with your vehicle identification number.
To adjust your data sharing preferences touch Controls > Software > Data Sharing > Allow Cabin Camera Analytics. You can
change your data sharing settings at any time.
Cleaning a Camera
To ensure a clear picture, the camera lens must be clean and free of obstructions, condensation, or damage.
Condensation can form inside the camera enclosures, especially if you park outside in cold or wet conditions. The touchscreen
may display an alert stating that a camera is blocked and that some (or all) Autopilot features may be temporarily restricted
until the camera vision is clear. To proactively dry the condensation, precondition the cabin by setting it to a warm
temperature, turning the windshield defroster on, and directing the front air vents toward the door pillars (see Mobile App on
page 355).
Remove any build-up of dirt or debris by spraying water onto the camera lens and carefully drying it with a microfiber cloth.
Clean the camera lens at least weekly during wet weather (snow, rain, sleet) and every month during dry weather.
The front-facing camera is equipped with a sprayer nozzle. To clean the front-facing camera, touch the app
launcher, select the Camera app, and press the spray icon.
CAUTION: Do not use chemical-based or abrasive cleaners. Doing so can damage the surface of the lens.
Drive to Calibrate Cameras
Before some Autopilot features can be used for the first time or after some types of service repairs, cameras must complete a
self-calibration process. When the cameras are calibrating, the instrument clustertouchscreen displays a progress indicator.
When calibration is complete, Autopilot features are available for use.
Calibration typically completes after driving 20-25 miles (32-40 km), but the distance varies depending on the conditions.
Calibration completes more quickly when driving on a straight road that has multiple lanes and highly visible lane markings in
both the driving lane and adjacent lanes (at least two lanes over on each side of the vehicle). For best results, drive in the
middle lane of a multi-lane highway (ideally with at least five lanes) that has clear lane markings and minimal traffic.
Schedule a service appointment only if your Model SModel XModel 3Model Y has not completed the calibration process after
driving approximately 100 miles (160 km) in the described conditions.
If a camera has shifted from its previously calibrated position (for example, the camera or windshield was replaced), clear the
calibration by touching Controls > Service > Camera Calibration > Clear Calibration. When the calibration is cleared,
Model SModel XModel 3Model Y repeats the calibration process.
NOTE: Model SModel XModel 3Model Y must repeat the calibration process if the cameras are serviced by Tesla, and in some
cases after a software update.
NOTE: If you attempt to use a feature that is not available until the calibration process is complete, the feature is not available
and the touchscreen displays a message.
1122
Owner's Manual
Opening and Closing
Keys
Types of Keys
NOTE: In the event you lose both key cards, schedule a service appointment through the mobile app to replace and pair them.
Model SModel XModel 3Model Y supports the following types of keys:
• Phone key - You can set up your personal phone as a "phone key" that communicates with Model SModel XModel 3Model
Y using Bluetooth (BLE). A phone key supports automatic locking and unlocking.
• Key card - Tesla provides key cards that communicate with Model SModel XModel 3Model Y using short range radiofrequency identification (RFID) signals. Unlike the phone key, the key card does not support automatic locking and
unlocking and must be touched against a card reader. In situations where your phone key has a dead battery, or is lost or
stolen, use your key card to unlock, drive, and lock Model SModel XModel 3Model Y.
Model SModel XModel 3Model Y supports a total of 19 keys, which can include phone keys and key cards.
CAUTION: Remember to bring a key (and a backup key) with you when you drive. Although you can drive
Model SModel XModel 3Model Y away from a detected key, you will be unable to power it back on after it powers off.
Phone Key
CAUTION: Do not leave your paired phone in your vehicle (for example, if you are hiking or at the beach). If you must
leave your phone in the vehicle, disable Bluetooth and/or turn the phone off and ensure that you keep a key card with
you.
Using your phone as a key is a convenient way to access your Model SModel XModel 3Model Y. As you approach your vehicle,
the smartphone's Bluetooth signal is detected and the doors unlock when you press a door open button. Likewise, when you
exit and walk away with the phone key, doors automatically lock (provided the Walk-Away Door Lock feature is turned on; see
Walk-Away Door Lock on page 1129).
Before you can use a phone to access Model SModel XModel 3Model Y, follow these steps to authenticate it (see XREF)
Once a phone has been authenticated, it no longer requires an internet connection to be used as a phone key for
Model SModel XModel 3Model Y. However, to use the phone hands-free, access your phone's contacts, play media from it,
etc., you must also pair it and connect it as a Bluetooth device (see Bluetooth on page 359).
NOTE: Some Android smartphones with NFC capability can be used to lock/unlock your vehicle, just like using a key card.
Ensure the Tesla mobile app is correctly paired to your vehicle and enable the NFC function on your phone. Once enabled,
simply hold the phone to the driver's side door pillar to lock or unlock the door. Refer to your smartphone's instructions for
specific information on how to do this.
To view a list of keys that can currently access Model SModel XModel 3Model Y, or to remove a phone key, touch Controls >
Locks (see Managing Keys on page 1125).
Model SModel XModel 3Model Y can connect to three phone keys simultaneously. Therefore, if more than three phone keys
are detected and you want to authenticate or pair a different phone, move the other connected phone key(s) out of range or
turn off its Bluetooth setting.
Key Card
Tesla provides you with two Model SModel XModel 3Model Y key cards, designed to fit in your wallet.
To use a key card to unlock or lock Model SModel XModel 3Model Y from outside, position the card as shown and tap it
against the card reader located approximately one third the way up of the driver's side door pillar. When
Model SModel XModel 3Model Y detects the key card, the exterior lights flash, the mirrors unfold or fold (if Fold Mirrors is
on), the horn sounds (if Lock Confirmation Sound is on), and the doors unlock or lock. You may need to hold the key card
against the transmitter for a few seconds.
Owner's Manual
1123
Opening and Closing
Once inside, power up Model SModel XModel 3Model Y by pressing the brake pedal within two minutes of scanning the key
card (see Starting and Powering Off on page 372). If you wait longer than two minutes, you must re-authenticate by placing
the key card near one of the card readers located on the wireless phone chargers on the center console. When your key card is
detected, your two-minute authentication period restarts.
NOTE: If enabled, Walk-Away Door Lock (see Walk-Away Door Lock on page 1129) operates only when you walk away using a
phone key. When you walk away carrying your key card, Model SModel XModel 3Model Y does not automatically lock.
1124
Owner's Manual
Opening and Closing
Managing Keys
To display a list of all keys that can access Model SModel XModel 3Model Y, touch Controls > Locks. An icon displays next to
each key to indicate whether the key is a phone key or a key card. Use this list to manage keys that have access to
Model SModel XModel 3Model Y. To add or delete keys, see Adding Keys from the Touchscreen on page 1125.
Model SModel XModel 3Model Y supports up to 19 keys. When you reach this limit, you must delete a key before adding a
new one.
NOTE: You can use the same key for more than one Tesla vehicle. This prevents you from having to deal with multiple keys
when you switch vehicles. If you customize the name of an authenticated key card on one vehicle (by touching the pencil icon),
any other vehicle to which the key card is authenticated also displays the changed name.
Adding Keys from the Touchscreen
If you have a key card that is already paired with your vehicle, you can pair a new key using the touchscreen.
1. On the touchscreen, touch Controls > Locks > Keys > Add Key.
2. Scan your key card on one of the card readers located on the wireless phone chargers on the center console.
3. Scan a key card that has already been paired to the vehicle to confirm new key pairing.
4. When complete, the key list includes the new key. Touch the associated pencil icon to customize the name of the key.
Pairing a New Phone Key
To set up your smartphone as a key:
1. Download the Tesla mobile app to your phone.
2. Log into the Tesla mobile app using your Tesla account username and password.
NOTE: You must remain logged in to your Tesla account to use your phone to access Model SModel XModel 3Model Y.
NOTE: If multiple vehicles are linked to your Tesla account, Model SModel XModel 3Model Y opens the most recent
vehicles in the mobile app for easy accesss.
3. Confirm:
◦ Your phone's Bluetooth setting is turned on.
◦ The Tesla mobile app can access your phone's Bluetooth. On your phone, navigate to Settings, choose the Tesla mobile
app, and ensure the Bluetooth setting is turned on.
◦ Allow the Tesla mobile app to access your location. For the best experience, keep the mobile app running in the
background.
◦ Mobile access is enabled for your vehicle. On the touchscreen, touch Controls > Safety > Allow Mobile Access.
NOTE: Model SModel XModel 3Model Y communicates with your phone using Bluetooth. Keep in mind that your phone
must have enough battery power to support Bluetooth (some phones disable Bluetooth when the battery is low).
4. While inside or near the vehicle, open the Tesla mobile app and touch Set Up Phone Key on the main screen, or navigate to
Security > Set Up Phone Key. Follow the prompts on the mobile app and vehicle touchscreen to set up your phone key.
NOTE: You must have your key card available in order to set up a phone key.
Adding Keys from the Mobile App
In the event that you don't have a working key card, you can add a new key using the mobile app.
NOTE: Only the owner of the vehicle is able to pair a new key using the mobile app.
NOTE: Pairing a key with the mobile app is supported with version 4.29.0 of the Tesla mobile app on vehicles with software
versions 2022.40 or higher.
1. While inside or near the vehicle, open the Tesla mobile app on your smartphone.
2. Touch Security & Drivers.
Owner's Manual
1125
Opening and Closing
3. Touch Add Key Card.
4. Scan your key card on one of the card readers located on the wireless phone chargers on the center console.
5. When the key is paired successfully, the mobile app shows a confirmation message. Touch Done in the mobile app and
remove the key card from the card reader.
6. When complete, the key list on the touchscreen includes the new key. Touch the associated pencil icon to customize the
name of the key.
Removing Keys
When you no longer want a key to access Model SModel XModel 3Model Y (for example, you lost your phone or key card,
etc.), follow these steps to remove it.
1. On the touchscreen, touch Controls > Locks.
2. In the key list, find the key that you would like to delete and touch its associated trash icon.
3. When prompted, scan an authenticated key on the card reader to confirm the deletion. When complete, the key list no
longer includes the deleted key.
NOTE: Model SModel XModel 3Model Y requires at least one authenticated key card or key fob or key fob at all times. If only
one key card remains on the key list, you cannot delete it.
Replacing Key cards
If you lose a key card, you can purchase replacement ones on the Tesla Shop. When ready to pair, simply follow the steps in
Managing Keys on page 1125. Remember to remove your old key cards from Controls > Locks > Keys for security purposes.
1126
Owner's Manual
Opening and Closing
Doors
Opening and Closing Doors from Outside
Doors are electrically powered. When you approach Model SModel XModel 3Model Y carrying a phone key, the doors and
tailgate automatically unlock. To open a door, press the exterior door release button on the pillar to the right of each door.
The doors do not automatically lock/unlock when you approach Model SModel XModel 3Model Y carrying only a key card. You
must manually lock/unlock the vehicle. See Keys on page 1123 for more information.
WARNING: Use caution around the panel edges on Model SModel XModel 3Model Y, including the doors, powered
frunk, tailgate, and surrounding panels.
WARNING: When pulling the door open, always grasp the door at the top, as shown. Keep hands and fingers away from
the opening edge and supervise children if they open and close the doors. This is especially important when handling a
front door where the opening edge can cause injury when opening or closing the associated rear door. Neglecting to
follow the correct opening procedure for front and rear doors can lead to injury.
Owner's Manual
1127
Opening and Closing
Whenever a door is open, the Door Open indicator displays on the touchscreen. Also, the image of the
Model SModel XModel 3Model Y on the touchscreen's Controls window provides a visual representation of the
open door(s).
To close a door from the outside, manually push it shut. Make sure no objects are in the way before closing the door.
Opening Doors from the Interior
To open a door while sitting inside, press interior door open button, located at the top of the interior door handle, and push the
door open.
NOTE: To prevent children from opening the rear doors, turn on child locks (see Child Locks on page 1130).
1128
Owner's Manual
Opening and Closing
NOTE: In the unlikely event that Model SModel XModel 3Model Y has no low voltage power, you will be unable to open the
doors with the interior door open button. See Opening Doors with No Power on page 1436 for more information.
Interior Locking and Unlocking
While sitting inside Model SModel XModel 3Model Y, you can lock or unlock all doors, the tailgate, and the powered frunk by
touching the lock icon on the touchscreen.
The icon changes to indicate whether doors are locked or unlocked.
When you stop Model SModel XModel 3Model Y and engage Park, you can choose to unlock all doors. To turn this feature on
or off, touch Controls > Locks > Unlock on Park.
Model SModel XModel 3Model Y automatically locks all doors (including the powered frunk and tailgate) when your driving
speed exceeds 5 mph (8 km/h). The touchscreen displays a message if the tailgate remains open after the vehicle locks.
Walk-Away Door Lock
NOTE: Model SModel XModel 3Model Y will still lock, even if the tonneau cover is open. In other words, once the vehicle is
locked, the tonneau cover is locked in its current position and cannot be open/closed using the tonneau cover switch on the
vehicle. Always double check to make sure the tonneau cover is closed.
The doors, tailgate, and powered frunk can automatically lock when you walk away carrying your phone key. To turn this
feature on or off, touch Controls > Locks > Walk-Away Door Lock.
When the vehicle locks, the exterior lights flash once. To also sound a confirmation chime when Model SModel XModel
3Model Y locks, touch Controls > Locks > Lock Confirmation Sound.
Model SModel XModel 3Model Y does not automatically lock if:
• You choose Exclude Home and Model SModel XModel 3Model Y is parked at the location you have designated as Home.
For details on how to designate a location as Home, see Home, Work, and Favorite Destinations on page 694.
• A key is detected inside Model SModel XModel 3Model Y (such as your phone or a key card resting on the card reader).
• A door or the powered frunk is not fully closed.
• The phone key's Bluetooth is not able to communicate with the vehicle or the phone's battery is dead.
• If Model SModel XModel 3Model Y detects an authenticated phone key for several minutes after you exit the vehicle and
close all doors, Walk-Away Lock disables and doors do not lock when you walk away. In this case, you must manually lock
your vehicle using a key card until after your next drive.
• The driver exits the vehicle without using the driver's door.
NOTE: It is your responsibility to ensure Model SModel XModel 3Model Y is locked, even when Walk-Away Door Lock is
enabled. You can check if Model SModel XModel 3Model Y is locked from the Tesla mobile app (see Mobile App on page
355).
Driver Door Unlock Mode
Enabling Controls > Locks > Driver Door Unlock Mode only unlocks the driver's door when you first unlock
Model SModel XModel 3Model Y. To unlock the remaining doors, long press the interior door open button, or use the
touchscreen or mobile app.
Disabling Driver Door Unlock Mode unlocks all doors, the powered frunk, and the tailgate when you first unlock
Model SModel XModel 3Model Y.
Owner's Manual
1129
Opening and Closing
Car Left Open Notifications
Receive a mobile notification if a door, the powered frunk and/or windows are left open or if Model SModel XModel 3Model Y
is left unlocked unexpectedly. Touch Controls > Locks > Car Left Open Notifications.
NOTE: Model SModel XModel 3Model Y will still lock, even if the tonneau cover is open. Always double check to make sure the
tonneau cover is closed. Car Left Open Notifications may not notify you if the tonneau cover is left open.
Child Locks
Model SModel XModel 3Model Y has child locks on the rear doors to prevent them from being opened using the interior door
open buttons. On the touchscreen, touch Controls > Locks > Child Lock. You can choose Both to engage the child lock on both
rear doors, or you can choose Left or Right to engage it on just a specific door.
WARNING: Tesla recommends turning on child locks whenever a child is seated in a rear seat.
1130
Owner's Manual
Opening and Closing
Windows
Opening and Closing
CAUTION: The windows automatically lower slightly when you open or close a door. This is normal and avoids damage to
the window when the door opens. If you manually raise a window when the door is open, ensure it is slightly lowered
before closing the door.
Press down on a switch to lower the associated window. Window switches operate at two levels:
• To lower a window fully, press the switch all the way down and immediately release.
• To lower a window partially, press the switch gently and release when the window is where you want it.
Similarly, pull a switch to raise the associated window:
• To raise a window fully, pull the switch all the way up and immediately release.
• To raise a window partially, pull the switch gently and release when the window is where you want it.
NOTE: If a window is fully lowered and you open the associated door, the window rises slightly. Likewise, if you fully lower a
window while the door is already open, it stops slightly above the edge of the door. To fully lower a window while the door is
open, press the switch again.
If a window is left open unintentionally, Model SModel XModel 3Model Y can send a notification to the mobile app (touch
Controls > Locks > Car Left Open Notification, then choose Doors & Windows). However, it is your responsibility to ensure
windows are closed after leaving the vehicle; do not rely on notifications to inform you.
Enable Close Windows on Lock by touching Controls > Locks > Close Windows on Lock to automatically close the windows
whenever the vehicle locks.
NOTE: See Cold Weather Best Practices on page 684 for information on preparing windows for cold weather.
WARNING: Before closing a window, it is the driver’s responsibility to ensure that all occupants, especially children, do
not have any body parts extended through the window’s opening. Failure to do so can cause serious injury.
WARNING: Never leave children unattended in Model SModel XModel 3Model Y.
Locking Rear Windows
To disable the rear window switches, touch Controls > Locks > Window Lock. Once locked, the rear windows can only be
controlled from the driver's window switch. Touch Window Lock again to re-enable the rear window switches.
Owner's Manual
1131
Opening and Closing
WARNING: To ensure safety, it is recommended that you lock the rear window switches whenever children are seated in
the rear seats.
If the PDF is very large, it may not load in the preview below.
Some older TSBs had multiple PDFs — visit the NHTSA Website to view all PDFs.
If the TSB PDF does not show, download or view it on the NHTSA Website.
Click on the (+) Plus Sign
Then Click on Associated Document(s)
Search NHTSA Database for Recalls
Search NHTSA Database for Vehicle Investigations
View Latest Vehicle Investigations
Search NHTSA Database for Vehicle Complaints
View Latest Vehicle Complaints
TSB/Document ID: fsd_12-5-1-2_082024.pdf
Replacement Service Bulletin Number:
MFR Communication Date: 2024-08-31
MFR Internal Campaign ID/Software Version: fsd-12-5-1-2
Communication Type: Over The Air
NHTSA Components: UNKNOWN OR OTHER
MFR Component System:
MFR Component Subsystem:
Previous TSB | Next TSB |
- [Notice] When you receive a used device, it may be a customer return resold by Amazon without inspection. You can exchange it for a new one through Amazon. As this situation is unavoidable, we sincerely apologize. For any issues, contacting us via Amazon's "Messages" is the best way. THINKSCAN 689BT Bidirectional Scan Tool Can Be Used Immediately After It is Turned On, Without Complicated Registration Process, Which is More Convenient & Quick.
- Full Bi-Directional Control & 3000+ Active Tests: Take control and test components like actuators, fuel injectors, relays, and cooling fans in real time. You’ll quickly see if the problem is in the part itself or the control module — saving you hours of guesswork and frustrating trial-and-error.
- Advanced ECU Coding Capabilities: Handle module matching and hidden feature activation with confidence. When you replace an ECU or want to customize settings, this obd2 scanner diagnostic bi directional tool gives you the professional-level capabilities you need without the dealership price tag.
- 34+ Useful Reset and Maintenance Functions: Complete everyday service tasks smoothly with a wide range of helpful reset and maintenance functions. Whether you’re keeping up with regular upkeep or tackling a specific job, this scanner makes maintenance simpler and less stressful for both DIYers and pros.
- Comprehensive Full System Diagnostics: Diagnose every major system — Engine, Transmission, ABS, SRS, TPMS, and more — all in one place. Finally stop wondering if you’re missing something important; get the full picture and clear codes with ease.
- Top Reasons to Choose the D7S OBD2 Scanner: XTOOL D7S car scan tool, an upgrade of XTOOL D7, offers comprehensive features for automotive technicians, workshops, and DIY enthusiasts 1. Upgraded Hardware: 2+64GB memory, rear camera, intuitive interface, foldable bracket 2. Complete Diagnostics: FCA
Autoauth, OE-level all system scan, 39+ maintenance services, 4K+ bidirectional, CANFD/DoIP protocol 3. Advanced Capabilities: ECU c0ding, PMI functions 4. Wide Compatibility: Support 10,000+ models, covering 99% vehicle brands 5. Multi-language: Available in 22+ languages, No IP Restrictions 6. 3-Year Updates: Save 300 bucks on software updates for the latest features and optimizations - 2026 Upgraded D7S Car Scanner Features: The newly 2026 D7S V2.0 scanner for car brings exciting features for advanced vehicle diagnostics and enhanced user experience 1. FCA
AutoAuth: Now supports FCA
SGW module for Chrysler
, for Jeep
, for Dodge
(2018+), for Fiat
(2017+), enabling faster vehicle communication without gateway restrictions 2. PMI (Offline ECU Pr0gramming): Allows for Ford
, for Lincoln
, and for Mazda
ECU pr0gramming for new modules 3. Optimized Diagnostic Report 2.0: Personalized reports with logos and customer info for auto shops. Note: Compatibility varies by cars, please check before order - 39+ Services/Resets/Adaptations/Relearns/Calibrations: XTOOL D7S full system car scanner diagnostic tool tackles 99% of common car issues through its 36+ special functions, including Oil Reset, EPB, SAS, BMS, Throttle Reset, Injector C0ding, ABS Bleed, TPMS Reset, Power Balance, etc and also covers specific-vehicle functions like Crank Sensor Relearn, ABS Initialization, Cylinder Power Balance, Fuel Trim Reset, Idle Relearn etc. This car diagnostic scanner enhances efficiency, making repairs and maintenance hassle-free. Tip: DO NOT for All vehicles, please check compatibility first
- Cost-effective ECU C0ding Scan Tool for Specific Brands: Enhance your vehicle's performance with XTOOL D7S! This obd2 scanner all systems bidirectional offers advanced capabilities at an affordable price, supports online for BMW
, for Benz and offline for BENZ, for MIT, along with PMI functions for Ford
, for Mazda
, and for Lincoln
. Ideal for technicians and DIY enthusiasts, this automotive scanner diagnostic tool optimizes vehicle performance and enhances the driving experience. Note: Not for all cars and modules, please send car VIN to check the compatibility before purchase - OE All System Diagnostic & 8 Pids Graphing: XTOOL D7S is a comprehensive all system bi directional obd2 scanner that delivers dealer-level diagnostics, completely controlling over your vehicle’s performance and health. This automotive scan tool can read and clear DTCs, view live data and ECU information, retrieve freeze frames, and perform active tests and full obd2 functions. This bi-directional scan tool can can identify your vehicle's make, model, and year information with just one click and show up to 8 PIDs live data with options for CSV viewing, playback, and recording for in-depth analysis. It is easy-to-use for both professionals and beginners, helping pinpoint issues efficiently
- 【✅Compared to BOSSCOMM IF742, IF745 Offers Full-System Diagnostics】The BOSSCOMM IF745 car diagnostic scanner is an upgraded model of IF742. In addition to supporting all OBD2 Code Reader functions and 6 reset options (ABS/EPB/SAS/BMS/Oil/Throttle), it expands diagnostics from 4 systems (Check Engine/ABS/SRS/Transmission) to vehicle All systems, including Steering, Suspension, and Body Electronics. This provides deeper, more comprehensive diagnostic capabilities.
- 【✨10 OBD2 Functions】The BOSSCOMM IF745 scan tool’s DTC Lookup instantly translates fault codes into user-friendly explanations, its I/M Readiness feature streamlines emissions testing with a single tap, and Freeze Frame lets you pinpoint the exact moment of a fault for in-depth root-cause diagnosis. Combined with a live data dashboard and advanced diagnostics (O2S, OBMon, EVAP), it delivers comprehensive insights for confident troubleshooting.
- 【✨Deep Diagnostics for All Vehicle System Modules】Beyond code reading/clearing and ECU information retrieval, our all-in-one data stream feature lets you inspect all current fault codes and their locations across the vehicle’s systems. This vehicle code reader helps you turn off dashboard warning lights and perform a comprehensive self-check of your car at home—no more back-and-forth trips to the repair shop or hefty inspection fees.
- 【✨6 Essential Resets: ABS Bleeding, Oil, EPB, SAS, Throttle, BMS】The BOSSCOMM IF745 obd2 scanner diagnostic tool swiftly purges air from brake lines to restore braking sensitivity, fine-tunes maintenance cycles to eliminate false alerts, resolves parking brake issues with one-click control, recalibrates steering sensors for stability, optimizes engine idling/acceleration for smoother performance, and deeply resets battery systems to extend lifespan and range via precise parameter adjustments.❗NOTE: Does NOT support bidirectional control, coding, or programming.
- 【✨10,000+ Car Models, AutoVIN, 13 Languages】The BOSSCOMM IF745 vehicle scanner diagnostic tool covers 73+ global car brands and offers support in 13 languages, making it perfect for DIYers, auto mechanics, or as a thoughtful gift. With a single-click AutoVIN feature, it instantly retrieves vehicle serial numbers, streamlining diagnostics for users globally. This adaptable tool balances user-friendliness with precision, catering to both personal and professional requirements.✅Unsure about compatibility? Compatibility will vary on vehicles' model and year, pls reach us via 📧 [email protected] 📧 before purchase.
This product presentation was made with AAWP plugin.




