L-SB-0005-24

Rev1

February 5, 2024

2025 UX 300h Pre-Delivery Service (PDS)
Service
Category

General

Section

Pre-Delivery Service

Market USA

Applicability
YEAR(S)

MODEL(S)

2025

UX300H

ADDITIONAL INFORMATION

REVISION NOTICE
June 11, 2024 Rev1:
 The Introduction, Required Tools & Equipment, Power Back Door Initialization, Tire Pressure
Warning System (TPWS) Initialization, Seating Position Control ECU Initialization, and Dealer
Contact Information for Call Dealer Head Unit Function sections have been updated.
 The Check Torque of Wheel Fasteners section has been removed.
Any previous printed versions of this bulletin should be discarded.

Introduction

Pre-Delivery Service (PDS) is a critical step in satisfying our new car customers. Customer
feedback indicates the following areas deserve special attention when performing PDS:





Careful inspection for paint chips/scratches and body dents/dings.
Proper operation of electrical accessories (including interior light, clock, and
radio reset).
Interior cleanliness.
Proper function of mechanical systems.

Customer retention and proper maintenance of vehicles are and have always been a major focus
for Lexus. To help remind customers that regular service is essential to the proper maintenance of
the vehicle, dealers are required to input their dealer information and set the service reminder on
the Navigation Screen before delivery. By doing this, customers will be reminded to return to your
dealership for service. (See Page 2 of the 2025 UX 300h Pre-Delivery Service (PDS) Check Sheet,
L-PDSB-0465-D, “Set Dealer and Service Reminder.”)
This bulletin contains the PDS procedures that apply specifically to the 2025 model year
UX 300h. To properly perform a complete PDS, you must complete all procedures contained in
this TSB.
In addition, if the vehicle is stored for over 30 days, refer to L-SB-0003-24, Long-Term Vehicle
Storage Guidelines.

© 2024 Lexus, a division of Toyota Motor Sales, USA

Page 1 of 13

L-SB-0005-24

Rev1

February 5, 2024

Page 2 of 13

2025 UX 300h Pre-Delivery Service (PDS)
Table of Contents



Warranty Information............................................................................................................. 3



Required Tools & Equipment ................................................................................................ 3



D/C Cut Fuse Installation ...................................................................................................... 4



Front License Plate and Mounting Bracket Installation*......................................................... 5



Front and Rear Emergency Towing Eyelet Removal and Hole Cover Installation.................. 7



Installation of Rubber Body Plugs ....................................................................................... 10



Power Back Door Initialization* ........................................................................................... 11



Tire Pressure Warning System (TPWS) Initialization........................................................... 11



Seating Position Control ECU Initialization* ........................................................................ 11



Head Unit System Reset ..................................................................................................... 11



Customize ACC Function .................................................................................................... 12



Deletion of Vehicle Alert History .......................................................................................... 12



Dealer Contact Information for Call Dealer Head Unit Function* ......................................... 12



Navigation — Set Date & Time by GPS .............................................................................. 13
*If applicable.

© 2024 Lexus, a division of Toyota Motor Sales, USA

L-SB-0005-24

Rev1

February 5, 2024

Page 3 of 13

2025 UX 300h Pre-Delivery Service (PDS)
Warranty Information

OP CODE

DESCRIPTION

TIME

OFP

T1

T2

N/A

Not Applicable to Warranty

–

–

–

–

Required Tools & Equipment
REQUIRED EQUIPMENT

SUPPLIER

Techstream ADVi*
Techstream 2.0
Techstream Lite

PART NUMBER

QTY

TSADVUNIT
ADE

Techstream Lite (Green Cable)

TS2UNIT
TSLITEPDLR01

1

TSLP2DLR01

*Essential SST.

NOTE
 Only ONE of the Techstream units listed above is required.
 GTS+ software version 2024.01.002.02 or later is required.
 Additional Techstream units may be ordered by calling Approved Dealer Equipment (ADE)
at 1-800-368-6787 or by visiting TIS – Diagnostics – Tools & Equipment – Techstream Order Portal.

© 2024 Lexus, a division of Toyota Motor Sales, USA

L-SB-0005-24

Rev1

February 5, 2024

Page 4 of 13

2025 UX 300h Pre-Delivery Service (PDS)
D/C Cut Fuse Installation

To minimize battery discharge during transportation and storage, the D/C cut fuse (30A) has been
removed at the assembly plant and temporarily stored in the blank space of the relay block in the
engine compartment. During PDS, reinstall the D/C cut fuse (30A) into its original location and
clear ALL related Diagnostic Trouble Codes (DTCs) are cleared.
Remove the D/C cut fuse (30A) from the blank space of the relay block in the engine
compartment and install the D/C cut fuse (30A) in the relay block as shown.
Figure 1.

A

2
1

A

Relay Block

1

Remove the D/C Cut Fuse (30A)

2

Install the D/C Cut Fuse (30A) (Original Location)

NOTE
 With the D/C cut fuse (30A) removed, if ANY DTCs are detected when the ignition is turned ON during
transportation, use Global Techstream Software (GTS+) to clear ALL DTCs AFTER ensuring that
there are NO malfunctions.
 While the vehicle is stored at the dealership, disconnect the negative (–) battery terminal to prevent
battery discharge. Refer to L-SB-0001-24, Battery Inspection and Maintenance During PDS, for
battery maintenance information.

© 2024 Lexus, a division of Toyota Motor Sales, USA

L-SB-0005-24

Rev1

February 5, 2024

Page 5 of 13

2025 UX 300h Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation

The front license plate bracket and two self-tapping screws are loaded in the vehicle at the
assembly plant. Follow this procedure to install the front license plate bracket and front license
plate in states where it is required by law.
1. Align holes “A” of the mounting bracket with the dimples on the radiator lower grille.
NOTE
 Holes “A” are used for installation of the front license plate mounting bracket to the radiator
lower grille.
 Holes “B” are used to install the license plate onto the mounting bracket.
Figure 2.
2

1

B

B

A

A

B

B

A

A

3

3
4

4

3

3

5

5

1

Non-F Sport Model

4

Dimples

2

F Sport Model

5

Self-tapping Screws

3

Mounting Bracket

2. Screw the two self-tapping screws directly into the dimples to install the front license plate
mounting bracket.
NOTICE
 Do NOT pre-drill holes into the dimples on the front bumper cover.
 Do NOT overtighten the self-tapping screws.

© 2024 Lexus, a division of Toyota Motor Sales, USA

L-SB-0005-24

Rev1

February 5, 2024

Page 6 of 13

2025 UX 300h Pre-Delivery Service (PDS)
Front License Plate and Mounting Bracket Installation (continued)

3. Install the front license plate onto the mounting bracket using two noncorroding bolts
with the following dimensions:
Nominal Length: 15.0 mm (0.59 in.)
Diameter: 6.0 mm (0.24 in.)
Figure 3.

Figure 4.
A

2

z

1
2

1

B

1

Nominal Length

2

Diameter

2